main
History Download
Ray Publish 0.1.0 d7a879a

INA296B4IDDFR

Texas Instruments · Current Sense Amplifiers · TSOT-23-8

INA296B4IDDFR from Texas Instruments, in a TSOT-23-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IN- input Current-sense amplifier negative input; for high-side use connect to the load side of the sense resistor, and for low-side use connect to the ground side.
2 GND power_in Ground reference for the device.
3 REF2 input Reference 2 voltage input; connect to a potential from 0V to VS.
4 NC unconnected Reserved pin; connect to ground.
5 OUT output Output voltage of the current-sense amplifier.
6 VS power_in Power supply input, 2.7V to 20V.
7 REF1 input Reference 1 voltage input; connect to a potential from 0V to VS.
8 IN+ input Current-sense amplifier positive input; for high-side use connect to the bus-voltage side of the sense resistor, and for low-side use connect to the load side.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TSOT-23-8
Category Amplifiers/Comparators
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Common-mode input range VCM -5 110 V VIN+, VIN- = -5V to 110V, VSENSE = 0mV, TA = -40°C to 125°C 5
Common-mode rejection ratio, input-referred (INA296B) CMRR 120 130 dB VIN+, VIN- = -5V to 110V, VSENSE = 0mV, TA = -40°C to 125°C 5
Offset voltage, input-referred (INA296B) Vos -150 25 150 µV VSENSE = 0mV 5
Offset voltage drift, input-referred (INA296B) dVos/dT -500 100 500 nV/°C TA = -40°C to 125°C 5
Power-supply rejection ratio, input-referred (INA296B) PSRR -10 1 10 µV/V VS = 2.7V to 20V, VSENSE = 0mV, VREF1 = VREF2 = 1V, TA = -40°C to 125°C 5
Input bias current IB 25 35 45 µA IB+, IB-, VSENSE=0mV 5
Gain error (INA296B) GERR -0.1 0.02 0.1 % (GND + 50mV) < VOUT < (VS - 200mV) 6
Gain error drift (INA296B) -5 0.2 5 ppm/°C TA = -40°C to +125°C 6
Swing to ground 8 20 mV RL = 10kΩ to GND, VSENSE = 0mV, VREF1 = VREF2 = 0V, TA = -40°C to +125°C 6
Reference voltage rejection ratio, input-referred (INA296B) RVRR -20 10 20 µV/V VREF1 = VREF2 = 0.5V to 4.5V, TA = -40°C to +125°C 6
Reference divider accuracy (INA296B) -0.15 0.02 0.15 % VOUT = /(VREF1 + VREF2)/ / 2 at VSENSE = 0mV, VREF1 = VS, VREF2 = GND or VREF1 = GND, VREF2 = VS, TA = -40°C to +125°C 6
Operating supply range VS 2.7 5 20 V 4
Common-mode input range (recommended) VCM -5 48 110 V 4
Ambient temperature (recommended) TA -40 125 °C 4
Supply voltage VS 22 V 4
Differential analog input voltage (VIN+ − VIN-) -30 30 V 4
Common-mode analog input voltage -20 120 V 4
REF1, REF2, NC inputs voltage -0.3 V Relative to GND; maximum VS + 0.3 4
Output voltage -0.3 V Relative to GND; maximum VS + 0.3 4
Operating temperature TA -55 150 °C 4
Junction temperature TJ 150 °C 4
Storage temperature Tstg -65 150 °C 4
Junction-to-ambient thermal resistance (DDF) RθJA 129.7 °C/W DDF (SOT23) 8-pin 4
Junction-to-case (top) thermal resistance (DDF) RθJC(top) 58 °C/W DDF (SOT23) 8-pin 4
Junction-to-board thermal resistance (DDF) RθJB 52.6 °C/W DDF (SOT23) 8-pin 4
Junction-to-top characterization parameter (DDF) ΨJT 2.3 °C/W DDF (SOT23) 8-pin 4
Junction-to-board characterization parameter (DDF) ΨJB 52.3 °C/W DDF (SOT23) 8-pin 4
Supply voltage range VS 2.7 20 V 7
Quiescent current IQ 2.5 3 mA VSENSE = 0mV 7
Quiescent current over temperature IQ 3.2 mA VSENSE = 0mV, TA = -40°C to +125°C 7
Specified ambient temperature range TA -40 125 °C 7
Bandwidth BW 1.1 MHz All gains, −3dB bandwidth 6
Slew rate, rising SR 8 V/µs 6
Settling time to 1% 1 µs VIN+, VIN- = 48V, VOUT = 0.5V to 4.5V, output settles to 1% 6
Voltage noise density (B4 device, 100V/V) 36 nV/√Hz A4, B4 devices 7
Gain (B4 device) G 100 V/V B4 devices 5

CAD (KiCad official)

  • Symbol: INA296B4IDDFR
  • Footprint: Package_TO_SOT_SMD:TSOT-23-8
  • 3D model: TSOT-23-8 (KiCad packages3D, STEP)
  • 3D model files: ina296b4iddfr-etched.step / ina296b4iddfr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ina296b4iddfr.step / ina296b4iddfr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (43 pp, sha256 a811e78481cbe850, retrieved 2026-11-05, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF