main
History Download
Ray Publish 0.1.0 92e04fa

INA253A2IPWR

Texas Instruments · Current Sense Amplifiers · TSSOP-20

INA253A2IPWR from Texas Instruments, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 IS- input Connect to load; analog current-sense input with absolute common-mode range GND - 6 V to 90 V.
2 IS- input Connect to load; analog current-sense input with absolute common-mode range GND - 6 V to 90 V.
3 IS- input Connect to load; analog current-sense input with absolute common-mode range GND - 6 V to 90 V.
4 SH- output Kelvin connection to the internal shunt; connect to IN- if no filtering is needed, with absolute common-mode range GND - 6 V to 90 V.
5 IN- input Voltage input from the load side of the shunt resistor; common-mode input range -4 V to 80 V.
6 GND power_in Ground reference for the device.
7 DNC1 unconnected Do not connect to any potential; leave this pin floating.
8 NC unconnected No connect.
9 VS power_in Analog power supply, 2.7 V to 5.5 V (absolute maximum 6 V).
10 REF2 input Reference voltage 2; must be kept between 0 V and VS and must not be connected to any voltage lower than GND or higher than VS.
11 REF1 input Reference voltage 1; must be kept between 0 V and VS and must not be connected to any voltage lower than GND or higher than VS.
12 NC unconnected No connect.
13 OUT output Analog output voltage, constrained to the supply rails (absolute maximum GND - 0.3 V to VS + 0.3 V).
14 DNC2 unconnected Do not connect to any potential; leave this pin floating.
15 NC unconnected Reserved; connect this pin to ground.
16 IN+ input Voltage input from the supply side of the shunt resistor; common-mode input range -4 V to 80 V.
17 SH+ output Kelvin connection to the internal shunt; connect to IN+ if no filtering is needed, with absolute common-mode range GND - 6 V to 90 V.
18 IS+ input Connect to supply; analog current-sense input with absolute common-mode range GND - 6 V to 90 V.
19 IS+ input Connect to supply; analog current-sense input with absolute common-mode range GND - 6 V to 90 V.
20 IS+ input Connect to supply; analog current-sense input with absolute common-mode range GND - 6 V to 90 V.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package TSSOP-20
Category Amplifiers/Comparators
Pins 20

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage 6 V 4
Shunt input current (ISENSE) continuous ISENSE -15 15 A Continuous 4
Analog inputs (IS+, IS-) common-mode -6 90 V Common-mode 4
Analog inputs (VIN+, VIN-) differential -80 80 V Differential (VIN+), (VIN-) 4
Analog inputs (VIN+, VIN-) common-mode -6 90 V Common-mode 4
Analog inputs (REF1, REF2, NC) -0.3 V Max printed as VS + 0.3 V (not numeric) 4
Analog outputs (SH+, SH-) common-mode -6 90 V Common-mode 4
Analog output (OUT) -0.3 V Max printed as VS + 0.3 V (not numeric) 4
Operating temperature TA -55 150 °C Operating free-air temperature range 4
Junction temperature TJ 150 °C 4
Storage temperature Tstg -65 150 °C 4
Electrostatic discharge, human-body model (HBM) V(ESD) -2000 2000 V Per ANSI/ESDA/JEDEC JS-001 4
Electrostatic discharge, charged-device model (CDM) V(ESD) -1000 1000 V Per JEDEC JESD22-C101 4
Common-mode input voltage VCM -4 80 V 4
Operating supply voltage VS 2.7 5.5 V 4
Operating free-air temperature TA -40 125 ℃ 4
Common-mode input range VCM -4 80 V VIN+ = -4 V to +80 V, ISENSE = 0 A, TA = -40°C to +125°C 5
Common-mode rejection CMR -500 125 500 µA/V VIN+ = -4 V to +80 V, ISENSE = 0 A, TA = -40°C to +125°C 5
Offset current, input-referred IOS -15 2.5 15 mA ISENSE = 0 A 5
Offset current drift dIOS/dT 25 125 µA/°C ISENSE = 0 A, TA = -40°C to +125°C 5
Power-supply rejection ratio PSRR -5 0.5 5 mA/V VS = 2.7 V to 5.5 V, ISENSE = 0 A 5
Reference input range 0 V Upper limit printed as VS (not numeric) 5
Shunt resistance (SH+ to SH-), equivalent with onboard amplifier RSHUNT 1.998 2 2.002 mΩ Equivalent resistance when used with onboard amplifier 5
Shunt resistance (SH+ to SH-), used as stand-alone resistor RSHUNT 1.9 2 2.1 mΩ Used as stand-alone resistor 5
Maximum continuous current ISENSE -15 15 A TA = -40°C to +85°C 5
Shunt short time overload -0.05 0.05 % ISENSE = 30 A for 5 seconds 5
Shunt thermal shock -0.1 0.1 % -65°C to +150°C, 500 cycles 5
Shunt resistance to solder heat -0.1 0.1 % 260°C solder, 10 seconds 5
Shunt high temperature exposure -0.15 0.15 % 1000 hours, TA = 150°C 5
Shunt cold temperature storage -0.025 0.025 % 24 hours, TA = -65°C 5
System gain error -0.4 0.05 0.4 % GND + 50 mV ≤ VOUT ≤ VS, 200 mV, TA = 25°C 5
System gain error drift -45 45 ppm/°C TA = -40°C to +125°C 5
Nonlinearity error -0.01 0.01 % GND + 10 mV ≤ VOUT ≤ VS, 200 mV 5
Reference divider accuracy 0.02 0.1 % VOUT = /(VREF1, VREF2)/ / 2 at ISENSE = 0 A, TA = -40°C to +125°C 5
Maximum capacitive load 1 nF No sustained oscillation 5
Operating voltage range VS 2.7 5.5 V TA = -40°C to +125°C 6
Quiescent current IQ 1.8 2.4 mA ISENSE = 0 A 6
Quiescent current vs temperature IQ 2.6 mA TA = -40°C to +125°C 6
Gain (INA253A2) G 200 mV/A 5
Reference voltage rejection ratio (input-referred), INA253A2 RVRR 2.5 mA/V 5
Bandwidth BW 350 kHz All gains, -3-dB bandwidth 6
Resistor temperature coefficient 15 ppm/°C TA = -40°C to +125°C 5
Resistor temperature coefficient 50 ppm/°C TA = -40°C to 0°C 5
Resistor temperature coefficient 10 ppm/°C TA = 0°C to 125°C 5
Junction-to-ambient thermal resistance RθJA 110.6 °C/W PW (TSSOP) 20 pins 4
Junction-to-case (top) thermal resistance RθJC(top) 54.1 °C/W PW (TSSOP) 20 pins 4
Junction-to-board thermal resistance RθJB 87.5 °C/W PW (TSSOP) 20 pins 4
Junction-to-top characterization parameter ψJT 114.1 °C/W PW (TSSOP) 20 pins 4
Junction-to-board characterization parameter ψJB 87.5 °C/W PW (TSSOP) 20 pins 4

CAD (KiCad official)

  • Symbol: INA253A2IPWR
  • Footprint: Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm
  • 3D model: TSSOP-20 (KiCad packages3D, STEP)
  • 3D model files: ina253a2ipwr-etched.step / ina253a2ipwr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ina253a2ipwr.step / ina253a2ipwr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (36 pp, sha256 f316d2de54cc0924, retrieved 2026-11-11, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF