← Commit history

Initial commit: component/ina209aipwr

Ray ·e817e0de20 ·
2 files changed +255
README.mdadded+52
@@ -0,0 +1,52 @@+# INA209AIPWR++**Texas Instruments** · Current Sense Amplifiers · TSSOP-16++INA209AIPWR from Texas Instruments, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VIN+ | power_in | Positive differential shunt voltage input; connect to positive side of shunt resistor; voltage range ±40mV to ±320mV depending on PGA gain setting; common-mode range 0V to 26V. |+| 2 | VIN- | power_in | Negative differential shunt voltage input; connect to negative side of shunt resistor; bus voltage measured from this pin to ground; common-mode range 0V to 26V. |+| 3 | Convert | input | Digital input to trigger conversions in triggered mode; normally held high, take low for minimum 4µs to initiate conversion; tie high if unused. |+| 4 | GND | power_in | Ground connection; must be connected together with pin 11 to system ground. |+| 5 | VS+ | power_in | Power supply input; supply voltage range 3V to 5.5V; draw maximum 1.5mA quiescent current; connect together with pin 10. |+| 6 | GPIO | bidirectional | General-purpose input/output with totem-pole output topology; user-programmable via Critical DAC+ register; default state is high-impedance input; can be configured as output 0, output 1, or Hi-Z. |+| 7 | Critical | tri_state | Open-drain critical watchdog output; active-low; transparent (non-latched) by default; responds to Critical DAC comparator within 5µs of overload condition detection. |+| 8 | Overlimit | tri_state | Open-drain over-limit watchdog output; active-low; transparent (non-latched) by default; responds to over-limit comparator thresholds for bus voltage and power limits. |+| 9 | Warning | tri_state | Open-drain warning watchdog output; active-low; transparent (non-latched) by default; responds to warning comparator thresholds with programmable delay 0 to 1.5s. |+| 10 | VS+ | power_in | Power supply input; supply voltage range 3V to 5.5V; draw maximum 1.5mA quiescent current; connect together with pin 5. |+| 11 | GND | power_in | Ground connection; must be connected together with pin 4 to system ground. |+| 12 | SCL | bidirectional | I²C serial bus clock line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout. |+| 13 | SDA | bidirectional | I²C serial bus data line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout. |+| 14 | A0 | input | Address input pin; sets slave address bits A0 for I²C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND. |+| 15 | A1 | input | Address input pin; sets slave address bits A1 for I²C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND. |+| 16 | SMBus Alert | tri_state | Open-drain SMBus alert output; active-low; responds to warning, over-limit, critical faults, or conversion ready states; latched and cleared by status register read or alert response; controlled via SMBus Alert Mask/Enable Control Register. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Texas Instruments |+| Package | TSSOP-16 |+| Category | Amplifiers/Comparators |+| Pins | 16 |++## CAD (KiCad official)++- Symbol: `INA209AIPWR`+- Footprint: `Package_SO:TSSOP-16_4.4x5mm_P0.65mm`+- 3D model: TSSOP-16 (KiCad packages3D, STEP)+- 3D model files: `ina209aipwr-etched.step` / `ina209aipwr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ina209aipwr.step` / `ina209aipwr.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/ina209) (50 pp, sha256 `fc088bc8d26a494f`, retrieved 2026-09-27, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.2`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-4-6` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/ina209aipwr-datasheet.pdf)
page.jsonadded+203
@@ -0,0 +1,203 @@+{+  "slug": "ina209aipwr",+  "version": "0.1.0",+  "type": "component",+  "description": "Texas Instruments Current Sense Amplifiers, TSSOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "amplifiers-comparators",+    "ina209aipwr",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "ina209aipwr.kicad_sym",+    "ina209aipwr.kicad_mod",+    "ina209aipwr.glb",+    "ina209aipwr.step",+    "ina209aipwr.lbr",+    "docs/hero.png",+    "docs/ina209aipwr-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "INA209AIPWR",+    "manufacturer": "Texas Instruments",+    "package": "TSSOP-16",+    "pin_count": 16,+    "category": "Amplifiers/Comparators",+    "subcategory": "Current Sense Amplifiers",+    "datasheet": "https://www.ti.com/cn/lit/gpn/ina209",+    "parts": {+      "symbol": "ina209aipwr.kicad_sym",+      "footprint": "ina209aipwr.kicad_mod",+      "model_3d": "ina209aipwr-etched.glb",+      "model_3d_plain": "ina209aipwr.glb",+      "model_3d_step": "ina209aipwr-etched.step",+      "model_3d_step_plain": "ina209aipwr.step",+      "lbr": "ina209aipwr.lbr"+    },+    "distributor_links": {+      "lcsc": "C485527",+      "digikey": "296-21951-2-ND",+      "mouser": "595-INA209AIPWR"+    },+    "distributor_check": {+      "checked_at": "2026-09-27T14:16:28Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "296-21951-2-ND",+        "status": "found"+      },+      "mouser": {+        "pn": "595-INA209AIPWR",+        "status": "found"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "VIN+",+        "type": "power_in",+        "description": "Positive differential shunt voltage input; connect to positive side of shunt resistor; voltage range ±40mV to ±320mV depending on PGA gain setting; common-mode range 0V to 26V."+      },+      {+        "number": "2",+        "name": "VIN–",+        "type": "power_in",+        "description": "Negative differential shunt voltage input; connect to negative side of shunt resistor; bus voltage measured from this pin to ground; common-mode range 0V to 26V."+      },+      {+        "number": "3",+        "name": "Convert",+        "type": "input",+        "description": "Digital input to trigger conversions in triggered mode; normally held high, take low for minimum 4µs to initiate conversion; tie high if unused."+      },+      {+        "number": "4",+        "name": "GND",+        "type": "power_in",+        "description": "Ground connection; must be connected together with pin 11 to system ground."+      },+      {+        "number": "5",+        "name": "VS+",+        "type": "power_in",+        "description": "Power supply input; supply voltage range 3V to 5.5V; draw maximum 1.5mA quiescent current; connect together with pin 10."+      },+      {+        "number": "6",+        "name": "GPIO",+        "type": "bidirectional",+        "description": "General-purpose input/output with totem-pole output topology; user-programmable via Critical DAC+ register; default state is high-impedance input; can be configured as output 0, output 1, or Hi-Z."+      },+      {+        "number": "7",+        "name": "Critical",+        "type": "tri_state",+        "description": "Open-drain critical watchdog output; active-low; transparent (non-latched) by default; responds to Critical DAC comparator within 5µs of overload condition detection."+      },+      {+        "number": "8",+        "name": "Overlimit",+        "type": "tri_state",+        "description": "Open-drain over-limit watchdog output; active-low; transparent (non-latched) by default; responds to over-limit comparator thresholds for bus voltage and power limits."+      },+      {+        "number": "9",+        "name": "Warning",+        "type": "tri_state",+        "description": "Open-drain warning watchdog output; active-low; transparent (non-latched) by default; responds to warning comparator thresholds with programmable delay 0 to 1.5s."+      },+      {+        "number": "10",+        "name": "VS+",+        "type": "power_in",+        "description": "Power supply input; supply voltage range 3V to 5.5V; draw maximum 1.5mA quiescent current; connect together with pin 5."+      },+      {+        "number": "11",+        "name": "GND",+        "type": "power_in",+        "description": "Ground connection; must be connected together with pin 4 to system ground."+      },+      {+        "number": "12",+        "name": "SCL",+        "type": "bidirectional",+        "description": "I²C serial bus clock line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout."+      },+      {+        "number": "13",+        "name": "SDA",+        "type": "bidirectional",+        "description": "I²C serial bus data line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout."+      },+      {+        "number": "14",+        "name": "A0",+        "type": "input",+        "description": "Address input pin; sets slave address bits A0 for I²C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND."+      },+      {+        "number": "15",+        "name": "A1",+        "type": "input",+        "description": "Address input pin; sets slave address bits A1 for I²C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND."+      },+      {+        "number": "16",+        "name": "SMBus Alert",+        "type": "tri_state",+        "description": "Open-drain SMBus alert output; active-low; responds to warning, over-limit, critical faults, or conversion ready states; latched and cleared by status register read or alert response; controlled via SMBus Alert Mask/Enable Control Register."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.2",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.2",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-4-6",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [],+        "pages_sent": 50,+        "cost_usd": 0.3738,+        "at": "2026-09-27T14:16:10"+      },+      "datasheet": {+        "url": "https://www.ti.com/cn/lit/gpn/ina209",+        "pages": 50,+        "sha256": "fc088bc8d26a494f",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 16,+        "described": 16,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file