← Commit history

Set visibility: public

Ray ·7b6f182095 · ·parent 43b41c6
1 file changed +12−9
page.json+12−9
@@ -52,11 +52,11 @@         "number": "1",         "name": "VIN+",         "type": "power_in",-        "description": "Positive differential shunt voltage input; connect to positive side of shunt resistor; voltage range \u00b140mV to \u00b1320mV depending on PGA gain setting; common-mode range 0V to 26V."+        "description": "Positive differential shunt voltage input; connect to positive side of shunt resistor; voltage range ±40mV to ±320mV depending on PGA gain setting; common-mode range 0V to 26V."       },       {         "number": "2",-        "name": "VIN\u2013",+        "name": "VIN–",         "type": "power_in",         "description": "Negative differential shunt voltage input; connect to negative side of shunt resistor; bus voltage measured from this pin to ground; common-mode range 0V to 26V."       },@@ -64,7 +64,7 @@         "number": "3",         "name": "Convert",         "type": "input",-        "description": "Digital input to trigger conversions in triggered mode; normally held high, take low for minimum 4\u00b5s to initiate conversion; tie high if unused."+        "description": "Digital input to trigger conversions in triggered mode; normally held high, take low for minimum 4µs to initiate conversion; tie high if unused."       },       {         "number": "4",@@ -88,7 +88,7 @@         "number": "7",         "name": "Critical",         "type": "tri_state",-        "description": "Open-drain critical watchdog output; active-low; transparent (non-latched) by default; responds to Critical DAC comparator within 5\u00b5s of overload condition detection."+        "description": "Open-drain critical watchdog output; active-low; transparent (non-latched) by default; responds to Critical DAC comparator within 5µs of overload condition detection."       },       {         "number": "8",@@ -118,25 +118,25 @@         "number": "12",         "name": "SCL",         "type": "bidirectional",-        "description": "I\u00b2C serial bus clock line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout."+        "description": "I²C serial bus clock line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout."       },       {         "number": "13",         "name": "SDA",         "type": "bidirectional",-        "description": "I\u00b2C serial bus data line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout."+        "description": "I²C serial bus data line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout."       },       {         "number": "14",         "name": "A0",         "type": "input",-        "description": "Address input pin; sets slave address bits A0 for I\u00b2C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND."+        "description": "Address input pin; sets slave address bits A0 for I²C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND."       },       {         "number": "15",         "name": "A1",         "type": "input",-        "description": "Address input pin; sets slave address bits A1 for I\u00b2C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND."+        "description": "Address input pin; sets slave address bits A1 for I²C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND."       },       {         "number": "16",@@ -220,5 +220,8 @@     "docs/ina209aipwr-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ]+  ],+  "visibility": {+    "public": true+  } }\ No newline at end of file