← Commit history

ina209aipwr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding)

Ray ·5f92150d03 · ·parent aba6edd
2 files changed +92−12
package.json+50−10
@@ -67,11 +67,11 @@         "number": "1",         "name": "VIN+",         "type": "power_in",-        "description": "Positive differential shunt voltage input; connect to positive side of shunt resistor; voltage range \u00b140mV to \u00b1320mV depending on PGA gain setting; common-mode range 0V to 26V."+        "description": "Positive differential shunt voltage input; connect to positive side of shunt resistor; voltage range ±40mV to ±320mV depending on PGA gain setting; common-mode range 0V to 26V."       },       {         "number": "2",-        "name": "VIN\u2013",+        "name": "VIN–",         "type": "power_in",         "description": "Negative differential shunt voltage input; connect to negative side of shunt resistor; bus voltage measured from this pin to ground; common-mode range 0V to 26V."       },@@ -79,7 +79,7 @@         "number": "3",         "name": "Convert",         "type": "input",-        "description": "Digital input to trigger conversions in triggered mode; normally held high, take low for minimum 4\u00b5s to initiate conversion; tie high if unused."+        "description": "Digital input to trigger conversions in triggered mode; normally held high, take low for minimum 4µs to initiate conversion; tie high if unused."       },       {         "number": "4",@@ -103,7 +103,7 @@         "number": "7",         "name": "Critical",         "type": "tri_state",-        "description": "Open-drain critical watchdog output; active-low; transparent (non-latched) by default; responds to Critical DAC comparator within 5\u00b5s of overload condition detection."+        "description": "Open-drain critical watchdog output; active-low; transparent (non-latched) by default; responds to Critical DAC comparator within 5µs of overload condition detection."       },       {         "number": "8",@@ -133,25 +133,25 @@         "number": "12",         "name": "SCL",         "type": "bidirectional",-        "description": "I\u00b2C serial bus clock line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout."+        "description": "I²C serial bus clock line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout."       },       {         "number": "13",         "name": "SDA",         "type": "bidirectional",-        "description": "I\u00b2C serial bus data line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout."+        "description": "I²C serial bus data line; open-drain; supports fast (400kHz) and high-speed (3.4MHz) modes; integrated spike suppression and Schmitt trigger; 28ms SMBus timeout."       },       {         "number": "14",         "name": "A0",         "type": "input",-        "description": "Address input pin; sets slave address bits A0 for I\u00b2C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND."+        "description": "Address input pin; sets slave address bits A0 for I²C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND."       },       {         "number": "15",         "name": "A1",         "type": "input",-        "description": "Address input pin; sets slave address bits A1 for I\u00b2C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND."+        "description": "Address input pin; sets slave address bits A1 for I²C bus addressing; sampled at start of each communication; configure via pull-up to VS+ or pull-down to GND."       },       {         "number": "16",@@ -192,6 +192,46 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "ina209aipwr.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          6.4,+          5.0,+          1.1+        ],+        "zmin_mm": -0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "6ad5e98224d02a427d9a6b929a28dbc158b9925fba5adec12db05079f1016948",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "ina209aipwr-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          6.4,+          5.0,+          1.1+        ],+        "zmin_mm": -0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "41e9f6ccb59a5eb5f7ee755f92271b6df15bee2b3b22f60c66a13b4a22a9ee19",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   }-}\ No newline at end of file+}
page.json+42−2
@@ -177,7 +177,47 @@     "viewers": {       "symbol": "viewers/symbol.html",       "footprint": "viewers/footprint.html"-    }+    },+    "models_3d": [+      {+        "file": "ina209aipwr.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          6.4,+          5.0,+          1.1+        ],+        "zmin_mm": -0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "6ad5e98224d02a427d9a6b929a28dbc158b9925fba5adec12db05079f1016948",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "ina209aipwr-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          6.4,+          5.0,+          1.1+        ],+        "zmin_mm": -0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "41e9f6ccb59a5eb5f7ee755f92271b6df15bee2b3b22f60c66a13b4a22a9ee19",+        "checked": "2026-10-07",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]   },   "metadata": {     "specs": {@@ -224,4 +264,4 @@   "visibility": {     "public": true   }-}\ No newline at end of file+}