main
Ray
ina200aidr: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding)
ab1432a
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166
{
"slug": "ina200aidr",
"version": "0.1.0",
"type": "component",
"description": "Texas Instruments Current-Sensing Amplifiers, SOIC-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.",
"tags": [
"component",
"op-amp-cmp",
"ina200aidr"
],
"dependencies": {},
"hero": {
"type": "image",
"path": "docs/hero.png"
},
"files": [
"page.json",
"README.md",
"ina200aidr.kicad_sym",
"ina200aidr.kicad_mod",
"ina200aidr.glb",
"ina200aidr.step",
"ina200aidr.lbr",
"docs/hero.png",
"docs/ina200aidr-datasheet.pdf",
"viewers/symbol.html",
"viewers/footprint.html",
"ina200aidr-etched.step"
],
"visibility": {
"public": true
},
"author": {
"name": "Ray"
},
"component": {
"mpn": "INA200AIDR",
"manufacturer": "Texas Instruments",
"package": "SOIC-8",
"pin_count": 8,
"category": "Current-Sensing Amplifiers",
"parts": {
"symbol": "ina200aidr.kicad_sym",
"footprint": "ina200aidr.kicad_mod",
"model_3d": "ina200aidr-etched.glb",
"model_3d_plain": "ina200aidr.glb",
"model_3d_step": "ina200aidr-etched.step",
"model_3d_step_plain": "ina200aidr.step",
"lbr": "ina200aidr.lbr"
},
"pins": [
{
"number": "1",
"name": "VS",
"type": "power_in",
"description": "Analog power supply input, 2.7 V to 18 V. Quiescent current up to 1800 uA (max). Bypass with a 0.1 uF ceramic capacitor close to the pin."
},
{
"number": "2",
"name": "OUT",
"type": "output",
"description": "Analog voltage output proportional to the shunt voltage times the fixed gain (20 V/V for INA200A). Output can swing rail-to-rail within specified swing limits; drives loads down to the specified minimum resistance."
},
{
"number": "3",
"name": "CMPIN",
"type": "input",
"description": "Non-inverting comparator input. Typically driven by a resistor divider from OUT to set the current trip threshold against the internal 0.6 V reference."
},
{
"number": "4",
"name": "GND",
"type": "power_in",
"description": "Device ground reference for the current-shunt monitor amplifier and the comparator/reference block."
},
{
"number": "5",
"name": "RESET",
"type": "input",
"description": "Active-low comparator latch reset input. Tie low (or leave floating) to run the comparator in transparent (non-latched) mode; drive high to enable latching of the comparator output after a trip event."
},
{
"number": "6",
"name": "CMPOUT",
"type": "output",
"description": "Open-drain comparator output. Pulls low when the CMPIN voltage exceeds the 0.6 V internal reference (over-current alert). Requires an external pull-up resistor to the desired logic rail."
},
{
"number": "7",
"name": "VIN-",
"type": "input",
"description": "Inverting current-shunt monitor input. Connect to the low-side (load-side) terminal of the external sense resistor. Common-mode range -16 V to +80 V independent of VS."
},
{
"number": "8",
"name": "VIN+",
"type": "input",
"description": "Non-inverting current-shunt monitor input. Connect to the high-side (bus-side) terminal of the external sense resistor. Common-mode range -16 V to +80 V independent of VS."
}
],
"provenance": {
"rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"
},
"viewers": {
"symbol": "viewers/symbol.html",
"footprint": "viewers/footprint.html"
},
"distributor_links": {
"lcsc": "C2869728",
"digikey": "296-28959-2-ND",
"mouser": "595-INA200AIDR"
},
"distributor_check": {
"checked_at": "2026-10-05T19:01:48Z",
"source": "Component Ocean /api/assign-pns + lcsc_map",
"digikey": {
"pn": "296-28959-2-ND",
"status": "found"
},
"mouser": {
"pn": "595-INA200AIDR",
"status": "found"
}
},
"models_3d": [
{
"file": "ina200aidr.step",
"role": "plain",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
6,
4.9,
1.75
],
"zmin_mm": 0,
"centre_offset_mm": 0,
"footprint_binding": "identity",
"sha256": "07f46cff378d30e6c27dfd5a03092c795323f86d91c71fc7e743f4f418dc553a",
"checked": "2026-10-07",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
},
{
"file": "ina200aidr-etched.step",
"role": "eda",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
6,
4.9,
1.75
],
"zmin_mm": 0,
"centre_offset_mm": 0,
"footprint_binding": "identity",
"sha256": "8baf8e9b94f1491bbc58d8fc0a9364251b99b94ae80cdfca8359b514ac40a15b",
"checked": "2026-10-07",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
}
]
}
}