Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

IL3085E

NVE · Digital Isolators · SOIC-16-300mil

IL3085E from NVE, in a SOIC-16-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD1 power_in Input power supply; recommended operating range is 3.0 V to 5.5 V.
2 GND1 power_in Input power supply ground return; internally connected to pin 8.
3 R output Receiver data output from the bus; the datasheet states it is forced to logic high if A/B are open or no driver is active, and it is tri-stated when RE is high.
4 RE input Read data enable, active low; when RE is high, R is high impedance.
5 DE input Drive enable, active high; enables the bus driver, and should be held low during power-up to avoid false drive pulses.
6 D input Data input to the bus driver.
7 NC unconnected No internal connection.
8 GND1 power_in Input power supply ground return; internally connected to pin 2.
9 GND2 power_in Output power supply ground return; internally connected to pin 15.
10 ISODE output Isolated DE output for PROFIBUS applications where the isolated drive enable state must be monitored, or for testing and troubleshooting.
11 NC unconnected No internal connection.
12 A bidirectional Non-inverting bus line; the differential bus voltage is measured as A with respect to B.
13 B bidirectional Inverting bus line; the differential bus voltage is measured as A with respect to B.
14 NC unconnected No internal connection.
15 GND2 power_in Output power supply ground return; internally connected to pin 9.
16 VDD2 power_in Output power supply; recommended operating range is 4.5 V to 5.5 V.

Key specifications

Parameter Value
Manufacturer NVE
Package SOIC-16-300mil
Category Interface ICs
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage Temperature TS -55 150 °C 2
Junction Temperature (absolute) TJ -55 150 °C 2
Ambient Operating Temperature (absolute) TA -40 85 °C 2
Voltage Range at A or B Bus Pins -8 12.5 V 2
Supply Voltage (absolute) VDD1, VDD2 -0.5 7 V 2
ESD (all bus nodes) 7 kV HBM 2
Supply Voltage VDD1 3 5.5 V 2
Supply Voltage VDD2 4.5 5.5 V 2
Junction Temperature (recommended) TJ -40 100 °C 2
Ambient Operating Temperature (recommended) TA -40 85 °C 2
Input Voltage at any Bus Terminal VI -7 12 V separately or common mode 2
High-Level Digital Input Voltage VIH 2.4 V VDD1 = 3.3 V; VDD1 = 5.0 V 2
Low-Level Digital Input Voltage VIL 0 0.8 V 2
Differential Input Voltage VID -7 12 V 2
High-Level Output Current (Driver) IOH 60 mA 2
High-Level Digital Output Current (Receiver) IOH 8 mA 2
Low-Level Output Current (Driver) IOL -60 mA 2
Low-Level Digital Output Current (Receiver) IOL -8 mA 2
Creepage Distance (external), IL3085E 8.03 8.3 mm Per IEC 60601 2
Total Barrier Thickness (internal) 0.012 0.013 mm 2
Comparative Tracking Index CTI 175 V Per IEC 60112 2
High Voltage Endurance, AC (maximum barrier voltage for indefinite life) VIO 1000 VRMS At maximum operating temperature 2
High Voltage Endurance, DC (maximum barrier voltage for indefinite life) VIO 1500 VDC At maximum operating temperature 2
Junction-Ambient Thermal Resistance, 0.3" SOIC θJA 34 °C/W Soldered to double-sided board; free air 2
Junction-Case (Top) Thermal Resistance, 0.3" SOIC θJT 17 °C/W 2
Power Dissipation, 0.3" SOIC PD 800 mW 2
Differential Output Voltage VOD3 1.5 2.3 5 V RL = 27 Ω, VDD = 4.5 V 6
Change in Magnitude of Differential Output Voltage Δ/VOD/ -0.2 0.01 0.2 V RL = 27 Ω or 50 Ω 6
Common Mode Output Voltage VOC 3 V RL = 27 Ω or 50 Ω 6
Change in Magnitude of Common Mode Output Voltage Δ/VOC/ -0.2 0.01 0.2 V RL = 27 Ω or 50 Ω 6
Output Current IO 1 mA Output Disabled, VO = 12 V 6
Output Current IO -0.8 mA Output Disabled, VO = −7 V 6
High Level Input Current IIH 10 μA VI = 3.5 V 6
Low Level Input Current IIL -10 μA VI = 0.4 V 6
Absolute /Short-circuit Output Current/ IOS 250 mA −7 V < VO < 12 V 6
Supply Current (VDD1 = 5 V) IDD1 4 6 mA VDD1 = 5 V, No Load (Outputs Enabled) 6
Supply Current (VDD1 = 3.3 V) IDD1 3 4 mA VDD1 = 3.3 V, No Load (Outputs Enabled) 6
Positive-going Input Threshold Voltage VIT+ 0.2 V −7 V < VCM < 12 V 7
Negative-going Input Threshold Voltage VIT− -0.2 V −7 V < VCM < 12 V 7
Low Level Digital Output Voltage VOL 0.2 V VID = −200 mV; IOH = 20 μA (as printed) 7
High-impedance-state Output Current IOZ -1 1 μA VO = 0.4 to (VDD2−0.5) V 7
Line Input Current II 1 mA VI = 12 V 7
Line Input Current II -0.8 mA VI = −7 V 7
Supply Current IDD2 5 16 mA No load; Outputs Enabled; VDD2X connected to VDD2I if applicable 7
Propagation Delay (VDD1 = 5 V, VDD2 = 5 V) tPD 48 150 ns VDD1 = 5 V, VDD2 = 5 V; VO = −1.5 to 1.5 V, CL = 15 pF 7
Pulse Skew (VDD1 = 5 V, VDD2 = 5 V) tSK(P) 6 15 ns VDD1 = 5 V, VDD2 = 5 V; VO = −1.5 to 1.5 V, CL = 15 pF 7
Output Enable Time To High Level (VDD1 = 5 V) tPZH 33 50 ns VDD1 = 5 V, VDD2 = 5 V; CL = 15 pF 7
Output Enable Time To Low Level (VDD1 = 5 V) tPZL 33 50 ns VDD1 = 5 V, VDD2 = 5 V; CL = 15 pF 7
Output Disable Time From High Level (VDD1 = 5 V) tPHZ 33 50 ns VDD1 = 5 V, VDD2 = 5 V; CL = 15 pF 7
Output Disable Time From Low Level (VDD1 = 5 V) tPLZ 33 50 ns VDD1 = 5 V, VDD2 = 5 V; CL = 15 pF 7
Common Mode Transient Immunity (VDD1 = 5 V) /CMH/,/CML/ 30 50 kV/μs VDD1 = 5 V, VDD2 = 5 V; VCM = 1500 VDC, tTRANSIENT = 25 ns 7
Propagation Delay (VDD1 = 3.3 V, VDD2 = 5 V) tPD 48 150 ns VDD1 = 3.3 V, VDD2 = 5 V; VO = −1.5 to 1.5 V, CL = 15 pF 7
Pulse Skew (VDD1 = 3.3 V, VDD2 = 5 V) tSK(P) 6 20 ns VDD1 = 3.3 V, VDD2 = 5 V; VO = −1.5 to 1.5 V, CL = 15 pF 7
Output Enable Time To High Level (VDD1 = 3.3 V) tPZH 33 50 ns VDD1 = 3.3 V, VDD2 = 5 V; CL = 15 pF 7
Output Enable Time To Low Level (VDD1 = 3.3 V) tPZL 33 50 ns VDD1 = 3.3 V, VDD2 = 5 V; CL = 15 pF 7
Output Disable Time From High Level (VDD1 = 3.3 V) tPHZ 33 50 ns VDD1 = 3.3 V, VDD2 = 5 V; CL = 15 pF 7
Output Disable Time From Low Level (VDD1 = 3.3 V) tPLZ 33 50 ns VDD1 = 3.3 V, VDD2 = 5 V; CL = 15 pF 7
Common Mode Transient Immunity (VDD1 = 3.3 V) /CMH/,/CML/ 30 50 kV/μs VDD1 = 3.3 V, VDD2 = 5 V; VCM = 1500 VDC, tTRANSIENT = 25 ns 7

CAD (KiCad official)

  • Symbol: IL3085E
  • Footprint: Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm
  • 3D model: SOIC-16-300mil (KiCad packages3D, STEP)
  • 3D model files: il3085e-etched.step / il3085e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); il3085e.step / il3085e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: NVE datasheet (20 pp, sha256 796d269550157078, retrieved 2026-11-12, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF