main
History Download
Ray Publish 0.1.0 42bb7a4

IIM-42653

TDK InvenSense · Sensors, Transducers · LGA-14

IIM-42653 from TDK InvenSense, in a LGA-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 AP_SDO / AP_AD0 output AP_SDO is the AP SPI serial data output in 4-wire mode, and AP_AD0 sets the LSB of the AP I3CSM/I2C slave address.
2 AUX1_SDIO bidirectional AUX1_SDIO is the AUX1 SPI serial data I/O used in 3-wire mode.
3 AUX1_SCLK output AUX1_SCLK is the AUX1 SPI serial clock.
4 INT1 / INT output INT1 is interrupt 1 and can be configured as push-pull or open drain; when INT is selected, all interrupts are mapped to this pin.
5 VDDIO power_in VDDIO is the IO power supply voltage, with an operating range of 1.71V to 3.6V.
6 GND power_in GND is the power supply ground.
7 RESV passive RESV is a reserved pin that must be connected to GND.
8 VDD power_in VDD is the power supply voltage, with an operating range of 1.71V to 3.6V.
9 INT2 / FSYNC / CLKIN input FSYNC is the frame sync input and must be connected to GND if unused, CLKIN is the external clock input (31 kHz to 50 kHz), and INT2 is interrupt 2 which can be push-pull or open drain.
10 AUX1_CS output AUX1_CS is the AUX1 SPI chip select.
11 AUX1_SDO output AUX1_SDO is the AUX1 SPI serial data output in 4-wire mode.
12 AP_CS input AP_CS is the AP SPI chip select and must be connected to VDDIO when the AP I3CSM or I2C interface is used.
13 AP_SCL / AP_SCLK input AP_SCL is the AP I3CSM/I2C serial clock, and AP_SCLK is the AP SPI serial clock.
14 AP_SDA / AP_SDIO / AP_SDI bidirectional AP_SDA is the AP I3CSM/I2C serial data, AP_SDIO is the AP SPI serial data I/O in 3-wire mode, and AP_SDI is the AP SPI serial data input in 4-wire mode.

Key specifications

Parameter Value
Manufacturer TDK InvenSense
Package LGA-14
Category Sensors, Transducers
Pins 14

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Sensitivity Scale Factor Initial Tolerance -0.5 0.5 % Component & Board-level, 25°C 11
Sensitivity Scale Factor Variation Over Temperature -0.005 0.005 %/ºC -40°C to +105°C 11
Nonlinearity -0.1 0.1 % Best fit straight line; 25°C 11
Cross-Axis Sensitivity -1.25 1.25 % Board-level 11
Initial ZRO Tolerance -0.5 0.5 º/s Board-level, 25°C 11
ZRO Variation vs. Temperature -0.04 0.04 º/s/ºC -40°C to +105°C 11
Output Data Rate 12.5 32000 Hz 11
Low Pass Filter Response 5 500 Hz ODR < 1kHz 11
Low Pass Filter Response 42 3979 Hz ODR ≥ 1kHz 11
Sensitivity Scale Factor Initial Tolerance -0.5 0.5 % Component & Board-level, 25°C 12
Sensitivity Change vs. Temperature -0.005 0.005 %/ºC -40°C to +105°C 12
Nonlinearity -0.1 0.1 % Best Fit Straight Line, ±2g 12
Cross-Axis Sensitivity -1 1 % Board-level 12
Initial Tolerance (Zero-G Output) -20 20 mg Board-level, all axes 12
Zero-G Level Change vs. Temperature -0.15 0.15 mg/ºC -40°C to +105°C 12
Output Data Rate 1.5625 32000 Hz 12
Low-Pass Filter Response 5 500 Hz ODR < 1kHz 12
Low-Pass Filter Response 42 3979 Hz ODR ≥ 1kHz 12
Supply Voltage VDD VDD 1.71 1.8 3.6 V 13
Supply Voltage VDDIO VDDIO 1.71 1.8 3.6 V 13
Specified Temperature Range -40 105 °C Performance parameters are not applicable beyond Specified Temperature Range 13
Supply Ramp Time 0.01 3 ms Monotonic ramp. Ramp rate is 10% to 90% of the final value 14
Operating Range (Temperature Sensor, Ambient) -40 105 °C Ambient 14
ODR With Filter (Temperature Sensor) 25 8000 Hz 14
Room Temperature Offset -5 5 °C 25°C 14
VOL, LOW-Level Output Voltage (I2C) VOL 0 0.4 V 3 mA sink current 14
Clock Frequency Initial Tolerance -3 3 % CLKSEL=2b00 or gyro inactive; 25°C 14
Clock Frequency Initial Tolerance -1.5 1.5 % CLK_SEL=2b01 and gyro active; 25°C 14
Frequency Variation over Temperature -3 3 % CLKSEL=2b00 or gyro inactive; -40°C to +85°C 14
Frequency Variation over Temperature -2 2 % CLK_SEL=2b01 and gyro active; -40°C to +85°C 14
RTC Clock Frequency FRTC 31 32 50 kHz Default 18
RTC Clock Rise Time tRISERTC 5 500 ns 18
RTC Clock Fall Time tFALLRTC 5 500 ns 18
Supply Voltage, VDD VDD -0.5 4 V 19
Supply Voltage, VDDIO VDDIO -0.5 4 V 19
Acceleration (Any Axis, unpowered) 20000 g for 0.2 ms 19
Operating Temperature Range -40 105 °C 19
Storage Temperature Range -40 125 °C 19
Electrostatic Discharge (ESD) Protection HBM 2 kV HBM 19
Electrostatic Discharge (ESD) Protection CDM 500 V CDM 19
Latch-up -100 100 mA JEDEC Class II, 125°C 19

CAD (KiCad official)

  • Symbol: IIM-42653
  • Footprint: Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y
  • 3D model: LGA-14 (KiCad packages3D, STEP)
  • 3D model files: iim-42653-etched.step / iim-42653-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); iim-42653.step / iim-42653.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TDK InvenSense datasheet, copy hosted by Mouser (131 pp, sha256 1e47624a3d59d84b, retrieved 2026-11-18)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF