Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
ICM-42688-P
TDK InvenSense · Accelerometers · LGA-14(2.5x3)
ICM-42688-P from TDK InvenSense, in a LGA-14(2.5x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AP_SDO / AP_AD0 | output | AP_SDO is the AP SPI serial data output in 4-wire mode, and AP_AD0 sets the LSB of the AP I3CSM/I2C slave address. |
| 2 | RESV | unconnected | Reserved pin; no connect or connect to GND. |
| 3 | RESV | unconnected | Reserved pin; no connect or connect to GND. |
| 4 | INT1 / INT | output | INT1 is interrupt 1 and can be push-pull or open drain; when INT is selected, all interrupts are mapped to this pin. |
| 5 | VDDIO | power_in | IO power supply voltage, operating from 1.71 V to 3.6 V. |
| 6 | GND | power_in | Power supply ground. |
| 7 | RESV | passive | Reserved pin; connect to GND. |
| 8 | VDD | power_in | Power supply voltage, operating from 1.71 V to 3.6 V. |
| 9 | INT2 / FSYNC / CLKIN | bidirectional | INT2 is interrupt 2 and can be push-pull or open drain; FSYNC is the frame sync input and should be connected to GND if unused; CLKIN is the external clock input. |
| 10 | RESV | unconnected | Reserved pin; no connect or connect to GND. |
| 11 | RESV | unconnected | Reserved pin; no connect or connect to GND. |
| 12 | AP_CS | input | AP SPI chip select; connect to VDDIO when using the AP I3CSM or I2C interface. |
| 13 | AP_SCL / AP_SCLK | input | AP_SCL is the AP I3CSM/I2C serial clock and AP_SCLK is the AP SPI serial clock. |
| 14 | AP_SDA / AP_SDIO / AP_SDI | bidirectional | AP_SDA is the AP I3CSM/I2C serial data, AP_SDIO is the SPI serial data I/O in 3-wire mode, and AP_SDI is the SPI serial data input in 4-wire mode. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TDK InvenSense |
| Package | LGA-14(2.5x3) |
| Category | Sensors |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Sensitivity Scale Factor Initial Tolerance | -0.5 | 0.5 | % | Component and Board-level, 25°C | 11 | ||
| Sensitivity Scale Factor Variation Over Temperature | -0.005 | 0.005 | %/ºC | 0°C to +70°C | 11 | ||
| Nonlinearity | -0.1 | 0.1 | % | Best fit straight line; 25°C | 11 | ||
| Cross-Axis Sensitivity | -1.25 | 1.25 | % | Board-level | 11 | ||
| Initial ZRO Tolerance | ZRO | -0.5 | 0.5 | º/s | Board-level, 25°C | 11 | |
| ZRO Variation vs. Temperature | ZRO | -0.005 | 0.005 | º/s/ºC | 0°C to +70°C | 11 | |
| Output Data Rate | ODR | 12.5 | 32000 | Hz | 11 | ||
| Low Pass Filter Response (gyro) | 5 | 500 | Hz | ODR < 1kHz | 11 | ||
| Low Pass Filter Response (gyro) | 42 | 3979 | Hz | ODR ≥ 1kHz | 11 | ||
| Sensitivity Scale Factor Initial Tolerance | -0.5 | 0.5 | % | Component and Board-level, 25°C | 12 | ||
| Sensitivity Change vs. Temperature | -0.005 | 0.005 | %/ºC | -40°C to +85°C | 12 | ||
| Nonlinearity | -0.1 | 0.1 | % | Best Fit Straight Line, ±2g | 12 | ||
| Cross-Axis Sensitivity | -1 | 1 | % | Board-level | 12 | ||
| Initial Tolerance (Zero-G Output) | -20 | 20 | mg | Board-level, all axes | 12 | ||
| Zero-G Level Change vs. Temperature | -0.15 | 0.15 | mg/ºC | -40°C to +85°C | 12 | ||
| Output Data Rate | ODR | 1.5625 | 32000 | Hz | 12 | ||
| Low-Pass Filter Response (accel) | 5 | 500 | Hz | ODR < 1kHz | 12 | ||
| Low-Pass Filter Response (accel) | 42 | 3979 | Hz | ODR ≥ 1kHz | 12 | ||
| Supply Voltage VDD | VDD | 1.71 | 1.8 | 3.6 | V | 13 | |
| Supply Voltage VDDIO | VDDIO | 1.71 | 1.8 | 3.6 | V | 13 | |
| Specified Temperature Range | -40 | 85 | °C | Performance parameters are not applicable beyond Specified Temperature Range | 13 | ||
| 6-Axis Gyroscope + Accelerometer Supply Current | 0.88 | mA | Low-Noise mode | 13 | |||
| Full-Chip Sleep Mode Current | 7.5 | µA | At 25ºC | 13 | |||
| Supply Ramp Time | 0.01 | 3 | ms | Monotonic ramp. Ramp rate is 10% to 90% of the final value | 14 | ||
| Temperature Sensor Operating Range | -40 | 85 | °C | Ambient | 14 | ||
| Temperature Sensor ODR With Filter | ODR | 25 | 8000 | Hz | With Filter | 14 | |
| Room Temperature Offset | -5 | 5 | °C | 25°C | 14 | ||
| Sensitivity Untrimmed | 132.48 | LSB/°C | 14 | ||||
| Sensitivity for FIFO data | 2.07 | LSB/°C | 14 | ||||
| I2C Low-Level Output Voltage | VOL | 0 | 0.4 | V | 3 mA sink current | 14 | |
| I2C Low-Level Output Current | IOL | 3 | mA | VOL=0.4 V | 14 | ||
| I2C Low-Level Output Current | IOL | 6 | mA | VOL=0.6 V | 14 | ||
| Output Fall Time | tof | 300 | ns | from VIHmax to VILmax, Cb bus capacitance in pf | 14 | ||
| INT Pulse Width | tINT | 8 | 100 | µs | int_tpulse_duration= 0 , 1 (100us, 8us ) | 14 | |
| Internal Clock Frequency Initial Tolerance | -3 | 3 | % | CLKSEL=`2b00 or gyro inactive; 25°C | 14 | ||
| Internal Clock Frequency Initial Tolerance | -1.5 | 1.5 | % | CLK_SEL=`2b01 and gyro active; 25°C | 14 | ||
| Internal Clock Frequency Variation over Temperature | -3 | 3 | % | CLKSEL=`2b00 or gyro inactive; -40°C to +85°C | 14 | ||
| Internal Clock Frequency Variation over Temperature | -2 | 2 | % | CLK_SEL=`2b01 and gyro active; -40°C to +85°C | 14 | ||
| External Clock Source Frequency | 31 | 32 | 50 | kHz | 14 | ||
| Supply Voltage VDD (absolute maximum) | VDD | -0.5 | 4 | V | 19 | ||
| Supply Voltage VDDIO (absolute maximum) | VDDIO | -0.5 | 4 | V | 19 | ||
| Acceleration (Any Axis, unpowered) | 20000 | g | for 0.2 ms | 19 | |||
| Operating Temperature Range | -40 | 85 | °C | 19 | |||
| Storage Temperature Range | -40 | 125 | °C | 19 | |||
| Electrostatic Discharge (HBM) | 2 | kV | HBM | 19 | |||
| Electrostatic Discharge (CDM) | 500 | V | CDM | 19 | |||
| Latch-up | -100 | 100 | mA | JEDEC Class II (2),125°C | 19 |
CAD (KiCad official)
- Symbol:
ICM-42688-P - Footprint:
Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm - 3D model: LGA-14(2.5x3) (KiCad packages3D, STEP)
- 3D model files:
icm-42688-p-etched.step/icm-42688-p-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);icm-42688-p.step/icm-42688-p.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: TDK InvenSense datasheet (110 pp, sha256
5710af9388adbb31, retrieved 2026-11-17, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).