3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownICL8038N
HGSEMI · Operational Amplifier · DIP-14
ICL8038N from HGSEMI, in a DIP-14. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SINE WAVE ADJ | input | Sine wave distortion adjust. External potentiometer between this pin and V- trims the sine wave symmetry/distortion. |
| 2 | SINE WAVE OUT | output | Sine wave output. Low-impedance analog waveform output, typical amplitude 0.22 x (V+ - V-). |
| 3 | TRIANGLE OUT | output | Triangle wave output. Analog output, amplitude typically 0.33 x (V+ - V-). |
| 4 | DUTY CYCLE/FREQ ADJ A | input | Duty cycle / frequency adjust input A. Timing resistor RA sets the rising slope current of the timing capacitor. |
| 5 | DUTY CYCLE/FREQ ADJ B | input | Duty cycle / frequency adjust input B. Timing resistor RB sets the falling slope current; combined with RA controls duty cycle from 2% to 98%. |
| 6 | V+ | power_in | Positive supply. Single supply +10 V to +30 V, or dual supply +/-5 V to +/-15 V. |
| 7 | FM BIAS | output | FM bias voltage. Internal reference used to set the nominal frequency; can be connected to pin 8 for basic (non-swept) operation. |
| 8 | FM SWEEP IN | input | FM sweep / VCO control input. Applying a voltage relative to V+ modulates the output frequency for FM or sweep operation. |
| 9 | SQUARE WAVE OUT | output | Square wave output. Open-collector output; requires an external pull-up resistor to V+ (or to a separate supply for level shifting). |
| 10 | TIMING CAP | passive | Timing capacitor connection. External capacitor C from this pin to V- sets the operating frequency together with RA and RB. |
| 11 | V-/GND | power_in | Negative supply / ground. Connect to ground for single-supply operation or to the negative rail for dual-supply operation. |
| 12 | SINE WAVE ADJ | input | Sine wave distortion adjust (second tap). Companion to pin 1 for full symmetry trim of the sine shaper. |
| 13 | NC | unconnected | No internal connection. |
| 14 | NC | unconnected | No internal connection. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HGSEMI |
| Package | DIP-14 |
| Category | Op-amp/Cmp |
| Pins | 14 |
Ordering variants
Same part, different packaging or reel option.
ICL8038NNICL8038NCCPDICL8038NCCJD
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (V- to V+) | 36 | V | 3 | ||||
| Input Current (Pins 4 and 5) | 25 | mA | 3 | ||||
| Output Sink Current (Pins 3 and 9) | 25 | mA | 3 | ||||
| Lead Temperature | 260 | ℃ | Soldering, 10 seconds | 3 | |||
| Maximum Storage Temperature Range | -65 | 150 | ℃ | 3 | |||
| Operating Temperature Range | 0 | 70 | ℃ | ICL8038A, ICL8038B, ICL8038 | 3 | ||
| Maximum Junction Temperature (Plastic Package) | 150 | ℃ | 3 | ||||
| Supply Voltage Operating Range (single supply) | VSUPPLY | 10 | 30 | V | V+ single supply | 4 | |
| Supply Voltage Operating Range (dual supplies) | VSUPPLY | 5 | 15 | V | V+, V- dual supplies (±5 V to ±15 V) | 4 | |
| Supply Current | ISUPPLY | 12 | 20 | mA | VSUPPLY= 10V (Note 2) | 4 | |
| Max. Frequency of Oscillation | fMAX | 100 | kHz | 4 | |||
| Square Wave Leakage Current | IOLK | 1 | µA | V9 = 30V | 4 | ||
| Square Wave Saturation Voltage | VSAT | 0.2 | 0.5 | V | ISINK = 2mA | 4 | |
| Typical Duty Cycle Adjust | ∆D | 2 | 98 | % | 4 | ||
| Triangle/Sawtooth/Ramp Amplitude | VTRIANGLE | 0.3 | 0.33 | xVSUPPLY | RTRI = 100kΩ | 4 | |
| Sine Wave Amplitude | VSINE | 0.2 | 0.22 | xVSUPPLY | RSINE = 100kΩ | 4 | |
| Total Harmonic Distortion | THD | 2 | 5 | % | RS = 1M (Note 4) | 4 | |
| Thermal Resistance θJA (DIP Package) | θJA | 115 | ℃/W | Typical (Note 2): component mounted on evaluation PC board in free air | 3 | ||
| Frequency Drift with Temperature | ∆f/∆T | 250 | ppm/℃ | 0℃ to 70℃ | 4 | ||
| Sweep Frequency of FM Input | fSWEEP | 10 | kHz | 4 | |||
| Sweep FM Range | 35 | :1 | Note 3: 82kΩ between pins 11 and 12, triangle duty cycle 50% | 4 | |||
| FM Linearity | 0.5 | % | 10:1 ratio | 4 | |||
| Frequency Drift with Supply Voltage | ∆f/∆V | 0.05 | %/V | Over supply voltage range | 4 | ||
| Rise Time | tR | 180 | ns | RL = 4.7kΩ | 4 | ||
| Fall Time | tF | 40 | ns | RL = 4.7kΩ | 4 | ||
| Triangle Waveform Linearity | 0.1 | % | 4 | ||||
| Output Impedance | ZOUT | 200 | Ω | IOUT = 5mA | 4 | ||
| THD Adjusted | THD | 1.5 | % | Use Figure 4 | 4 |
CAD (KiCad official)
- Symbol:
ICL8038N - Footprint:
Package_DIP:DIP-14_W7.62mm - 3D model: DIP-14 (KiCad packages3D, STEP)
- 3D model files:
icl8038n-etched.step/icl8038n-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);icl8038n.step/icl8038n.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HGSEMI datasheet (19 pp, sha256
97bbe39cca573c2e, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).