Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

ICE5AR3995BZXKLA1

Infineon Technologies · AC-DC Controllers & Regulators · DIP-7

ICE5AR3995BZXKLA1 from Infineon Technologies, in a DIP-7. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VERR passive VERR is internally connected to the transconductance error amplifier for a non-isolated converter, and must be connected to GND for an isolated converter.
2 FB input FB combines feedback control, selectable burst entry/exit control, and overload/open-loop protection.
3 CS input CS connects to the external shunt resistor for primary current sensing and internally to the PWM signal generator, where it determines switch-off together with the feedback voltage.
4 GATE output GATE drives the internal CoolMOS gate and is also pulled up to bus voltage through a resistor to turn on the CoolMOS for charging the VCC capacitor during startup.
5 DRAIN passive DRAIN is connected to the drain of the integrated CoolMOS.
7 VCC power_in VCC is the positive supply to the IC, with an operating range between VVCC_OFF and VVCC_OVP.
8 GND power_in GND is the common ground of the controller.

Key specifications

Parameter Value
Manufacturer Infineon Technologies
Package DIP-7
Category Power Management
Pins 7

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Drain voltage VDRAIN 950 V Tj = 25°C 20
Pulse drain current (ICE5xR3995xZ) ID,Pulse 5.01 A Pulse width tP limited by Tj,max. 20
Avalanche energy, repetitive (ICE5xR3995xZ) EAR 0.04 mJ tAR limited by maximal Tj=150°C and Tj,Start=25°C; ID = 0.20 A, VDD = 50 V 20
Avalanche current, repetitive (ICE5xR3995xZ) IAR 0.2 A tAR limited by maximal Tj=150°C and Tj,Start=25°C 20
VCC supply voltage VCC -0.3 27 V 20
GATE voltage VGATE -0.3 27 V 20
FB voltage VFB -0.3 3.6 V 20
VERR voltage VERR -0.3 3.6 V 20
CS voltage VCS -0.3 3.6 V 20
VIN voltage VVIN -0.3 3.6 V 20
Maximum DC current on any pin -10 10 mA Except DRAIN and CS pin. 20
Junction temperature range Tj -40 150 °C Controller and CoolMOS™. 21
Storage temperature TSTORE -55 150 °C 21
Thermal resistance (junction-ambient) (ICE5xR3995xZ) RthJA 106 K/W Setup per JEDEC JESD51, minimum drain pin copper area in a 2 oz copper single-sided PCB 21
VCC charge current, step 1 IVCC_Charge1 -0.35 -0.2 -0.09 mA VVCC = 0 V, RStartUp = 50 MΩ and VDRAIN = 90 V 21
VCC charge current, step 3 IVCC_Charge3 -5 -3 -1 mA VVCC = 15 V, RStartUp = 50 MΩ and VDRAIN = 90 V 21
VCC turn-on threshold voltage VVCC_ON 15.3 16 16.5 V 22
VCC turn-off threshold voltage VVCC_OFF 9.4 10 10.4 V 22
VCC short circuit protection VVCC_SCP 1.1 1.9 V 22
Internal reference voltage VREF 3.2 3.3 3.39 V Measured at FB pin IFB = 0 A 22
Fixed oscillator frequency, 100 kHz (fOSC3) fOSC3 92 100 108 kHz 22
Fixed oscillator frequency, 100 kHz (fOSC4) fOSC4 94 100 106 kHz Tj =25°C 22
Fixed oscillator frequency, 100 kHz (ABM) fOSC4_ABM 71 83 94 kHz Tj =25°C 22
Fixed oscillator frequency, 100 kHz (minimum Fsw) fOSC4_MIN 36 43 51 kHz Tj =25°C 22
Maximum duty cycle DMAX 70 75 80 % 23
Feedback pull-up resistor RFB 11 15 20 kΩ 23
PWM-OP gain GPWM 1.91 2.03 2.16 23
Offset for voltage ramp VPWM 0.42 0.5 0.58 V 23
Slope compensation rate, 100 kHz MCOMP 41 50 58 mV/μs Vcs= 0 V 23
Transconductance GERR_M 2.14 2.8 3.44 mA/V 23
Transconductance, Burst mode GERR_BM 6.9 9.2 11.6 mA/V 23
Error amplifier source current IERR_SOURCE 85 150 223 μA 23
Error amplifier sink current IERR_SINK 85 150 223 μA 23
Error amplifier reference voltage VERR_REF 1.76 1.8 1.84 V 23
Error amplifier output dynamic range of transconductance VERR_DYN 0.05 3.15 V 23
Error amplifier mode bias current IERR_P_BIAS 9.5 14 18.5 μA 23
Error amplifier mode threshold VERR_P_BIAS 0.16 0.2 0.24 V 23
Peak current limitation in normal operation VCS_N 0.72 0.8 0.88 V dVsense/dt = 0.41 V/μ s 23
Peak current limitation in normal operation, 15% of TON VCS_N15 0.74 0.79 0.84 V 23
Leading edge-blanking time tCS_LEB 70 220 365 ns 23
Peak current limitation in ABM, high power VCS_BHP 0.23 0.27 0.31 V 23
Peak current limitation in ABM, low power VCS_BLP 0.18 0.22 0.26 V 24
Abnormal CS voltage threshold VCS_STG 0.06 0.1 0.15 V 24
Soft start time tSS 7.3 12 ms 24
Charging current to select burst mode Isel 2.5 3 3.5 µA 24
Burst mode selection reference voltage threshold 1 VFB_P_BIAS1 1.65 1.73 1.8 V 24
Burst mode selection reference voltage threshold 2 VFB_P_BIAS2 2.76 2.89 3.01 V 24
Feedback voltage for entering ABM for high power VFB_EBHP 0.98 1.03 1.08 V 24
Feedback voltage for entering ABM for low power VFB_EBLP 0.88 0.93 0.98 V 24
Feedback voltage for leaving ABM VFB_LB 2.63 2.73 2.83 V 24
Feedback voltage for burst-on, isolated case VFB_Bon_ISO 2.26 2.35 2.45 V 24
Feedback voltage for burst-off, isolated case VFB_BOff_ISO 1.88 2 2.05 V 24
Feedback voltage for burst-on, non-isolated case VFB_Bon_NISO 1.88 1.95 2.05 V 25
Feedback voltage for burst-off, non-isolated case VFB_BOff_NISO 1.5 1.55 1.64 V 25
VCC overvoltage threshold VVCC_OVP 24 25.5 27 V 25
Overload detection threshold for OLP protection at FB pin VFB_OLP 2.63 2.73 2.83 V 25
Overload protection blanking time tFB_OLP_B 30 54 ms 25
Overtemperature protection (controller chip) Tjcon_OTP 129 140 150 °C Junction temperature of the controller chip (not the CoolMOS™ chip). Not subject to production test. 25
Drain source breakdown voltage (ICE5xR3995xZ) V(BR)DSS 950 V Tj = 25°C 26
Drain source on-resistance (inclusive of low side MOSFET), ICE5xR3995xZ RDSon 3.46 4.05 Ω Tj = 25°C 26

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper minimum drain pin copper area in a 2 oz copper single-sided PCB. The output power figure is for selection purpose only. The actual 3

CAD (KiCad official)

  • Symbol: ICE5AR3995BZXKLA1
  • Footprint: Package_DIP:DIP-8-N6_W7.62mm
  • 3D model: DIP-7 (KiCad packages3D, STEP)
  • 3D model files: ice5ar3995bzxkla1-etched.step / ice5ar3995bzxkla1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ice5ar3995bzxkla1.step / ice5ar3995bzxkla1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Infineon Technologies datasheet (40 pp, sha256 2fcad70c6f240373, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF