component
HX7662-P
Public Made by Adomby adom
ZHHXDZ Charge Pumps, DIP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
HX7662-P
ZHHXDZ · Charge Pumps · DIP-8
HX7662-P from ZHHXDZ, in a DIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TEST | passive | Test pin that is not connected in normal use; tying it to V+ disconnects the internal oscillator from the OSC pin so the pump runs at a faster rate. |
| 2 | CAP+ | passive | Positive terminal of the pump capacitor C1, which must be connected to this pin. |
| 3 | GROUND | power_in | Ground reference pin; it is also the cascade connection point (pin 8 of a stage ties to pin 3 of the previous stage) and the split-supply midpoint. |
| 4 | CAP- | passive | Other (negative) terminal of the pump capacitor C1, switched between V+ and GND by the internal MOS switches. |
| 5 | VOUT | power_out | Negative output, Vout = -n x V+; output source resistance is about 60 ohm at +15V supply, and Vout should not be shorted to V+ for extended periods. |
| 6 | LV | input | Low-voltage pin that should be connected to GND for supplies below 8V to improve efficiency, and left open for higher supply voltages. |
| 7 | OSC | input | Oscillator pin left open for the nominal 10kHz oscillator; an external capacitor to V+ lowers the frequency, and an external clock may be applied through a 1k ohm series resistor. |
| 8 | V+ | power_in | Positive supply input rated for +4.5V to +20V, with an absolute maximum of -0.3V to +22V to GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ZHHXDZ |
| Package | DIP-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| V+ to GND | -0.3 | 22 | V | 2 | |||
| Oscillator Input to GND | -0.3 | V | V+ < 12V (Note 1); upper limit printed as V+ +0.3 V | 2 | |||
| Operating Temperature Range (Commercial) | 0 | 70 | °C | Commercial grade; grade of HX7662-P not stated in datasheet | 2 | ||
| Operating Temperature Range (Extended) | -40 | 85 | °C | Extended grade; grade of HX7662-P not stated in datasheet | 2 | ||
| Operating Temperature Range (Military) | -55 | 125 | °C | Military grade; grade of HX7662-P not stated in datasheet | 2 | ||
| Storage Temperature | -65 | 160 | °C | 2 | |||
| Lead Temperature | 300 | °C | Value reconstructed from text split as '+30' and '0 ℃'; duration not printed | 2 | |||
| Supply Voltage Range | 4.5 | 20 | V | Features text: +4.5V to +20V supply (to -4.5V to -20V output); not taken from garbled electrical table | 1 | ||
| Oscillator Frequency (nominal) | fosc | 10 | kHz | OSC pin left open (nominal; charge pump 5 kHz); from Applications text | 5 | ||
| Output Source Resistance | 60 | Ω | V+ = 15V; from Negative Voltage Converter text (approximate) | 6 | |||
| Open Circuit Conversion Efficiency | 99.7 | % | Open circuit; from features text | 1 |
CAD (KiCad official)
- Symbol:
HX7662-P - Footprint:
Package_DIP:DIP-8_W7.62mm - 3D model: DIP-8 (KiCad packages3D, STEP)
- 3D model files:
hx7662-p-etched.step/hx7662-p-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hx7662-p.step/hx7662-p.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ZHHXDZ datasheet (9 pp, sha256
601a71494a8c3c2b, retrieved 2026-10-15, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# HX7662-P
**ZHHXDZ** · Charge Pumps · DIP-8
HX7662-P from ZHHXDZ, in a DIP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TEST | passive | Test pin that is not connected in normal use; tying it to V+ disconnects the internal oscillator from the OSC pin so the pump runs at a faster rate. |
| 2 | CAP+ | passive | Positive terminal of the pump capacitor C1, which must be connected to this pin. |
| 3 | GROUND | power_in | Ground reference pin; it is also the cascade connection point (pin 8 of a stage ties to pin 3 of the previous stage) and the split-supply midpoint. |
| 4 | CAP- | passive | Other (negative) terminal of the pump capacitor C1, switched between V+ and GND by the internal MOS switches. |
| 5 | VOUT | power_out | Negative output, Vout = -n x V+; output source resistance is about 60 ohm at +15V supply, and Vout should not be shorted to V+ for extended periods. |
| 6 | LV | input | Low-voltage pin that should be connected to GND for supplies below 8V to improve efficiency, and left open for higher supply voltages. |
| 7 | OSC | input | Oscillator pin left open for the nominal 10kHz oscillator; an external capacitor to V+ lowers the frequency, and an external clock may be applied through a 1k ohm series resistor. |
| 8 | V+ | power_in | Positive supply input rated for +4.5V to +20V, with an absolute maximum of -0.3V to +22V to GND. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ZHHXDZ |
| Package | DIP-8 |
| Category | Power Management (PMIC) |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| V+ to GND | | -0.3 | | 22 | V | | 2 |
| Oscillator Input to GND | | -0.3 | | | V | V+ < 12V (Note 1); upper limit printed as V+ +0.3 V | 2 |
| Operating Temperature Range (Commercial) | | 0 | | 70 | °C | Commercial grade; grade of HX7662-P not stated in datasheet | 2 |
| Operating Temperature Range (Extended) | | -40 | | 85 | °C | Extended grade; grade of HX7662-P not stated in datasheet | 2 |
| Operating Temperature Range (Military) | | -55 | | 125 | °C | Military grade; grade of HX7662-P not stated in datasheet | 2 |
| Storage Temperature | | -65 | | 160 | °C | | 2 |
| Lead Temperature | | | | 300 | °C | Value reconstructed from text split as '+30' and '0 ℃'; duration not printed | 2 |
| Supply Voltage Range | | 4.5 | | 20 | V | Features text: +4.5V to +20V supply (to -4.5V to -20V output); not taken from garbled electrical table | 1 |
| Oscillator Frequency (nominal) | fosc | | 10 | | kHz | OSC pin left open (nominal; charge pump 5 kHz); from Applications text | 5 |
| Output Source Resistance | | | 60 | | Ω | V+ = 15V; from Negative Voltage Converter text (approximate) | 6 |
| Open Circuit Conversion Efficiency | | | 99.7 | | % | Open circuit; from features text | 1 |
## CAD (KiCad official)
- Symbol: `HX7662-P`
- Footprint: `Package_DIP:DIP-8_W7.62mm`
- 3D model: DIP-8 (KiCad packages3D, STEP)
- 3D model files: `hx7662-p-etched.step` / `hx7662-p-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `hx7662-p.step` / `hx7662-p.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [ZHHXDZ datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603130172669915136) (9 pp, sha256 `601a71494a8c3c2b`, retrieved 2026-10-15, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/hx7662-p-datasheet.pdf)