Generated by kicad-footprint-generator · KiCad file format 20260206
HX75176-S
ZHHXDZ · RS-485 / RS-422 ICs · SOP-8
HX75176-S from ZHHXDZ, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver data output: RO is high for A-B of -50 mV and low for A-B of -200 mV when RE is low, and it stays high for an open or shorted receiver input. |
| 2 | RE | input | Receiver output enable, active low: the receiver output is effective when RE is low and RO is high-impedance when RE is high. |
| 3 | DE | input | Driver output enable: the chip is in transmit state when DE is high, and A/B are high-impedance when DE is low. |
| 4 | DI | input | Driver data input: with DE high, A follows DI and B is driven to the opposite level. |
| 5 | GND | power_in | Ground reference for the device. |
| 6 | A | bidirectional | Driver data output and receiver data input for the bus line A; the receiver input impedance is 1/8 unit load. |
| 7 | B | bidirectional | Driver data output and receiver data input for the bus line B; the receiver input impedance is 1/8 unit load. |
| 8 | Vcc | power_in | Power supply; the working voltage range is 4.5 V to 5.5 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ZHHXDZ |
| Package | SOP-8 |
| Category | Interface |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | -0.5 | 6 | V | 2 | ||
| Control input voltage (DE, RE) | DE,RE | -0.3 | 6 | V | 2 | ||
| Drive input voltage | DI | 6 | V | 2 | |||
| Drive output voltage / receive input voltage | A,B | -7 | 12 | V | 2 | ||
| Receiving output voltage | RO | -0.3 | V | Maximum printed as VCC+0.3 | 2 | ||
| Storage temperature range | TSTG | -55 | 150 | ℃ | 2 | ||
| Operating temperature range | TOP | -40 | 85 | ℃ | 2 | ||
| Maximum operating temperature range | TMOP | -55 | 125 | ℃ | 2 | ||
| Power dissipation | PD | 470 | mW | SOP-8 (+70℃ or above) | 2 | ||
| Solder temperature | TL | 300 | ℃ | 10 seconds | 2 | ||
| Working voltage range | Vcc | 4.5 | 5.5 | V | Vcc=5V±5%, TA=25℃ | 2 | |
| Driver differential output (with load) | VOD2 | 1.5 | V | R=54Ω or R=27Ω, Figure 1 | 2 | ||
| Driver differential output (no load) | VOD1 | 5 | V | 2 | |||
| Change in differential output voltage magnitude | ΔVOD | 0.2 | V | DI changes | 2 | ||
| Driver common mode output voltage | VOC | 3 | V | 2 | |||
| Change in common mode output voltage | ΔVOC | 0.2 | V | DI changes | 2 | ||
| Input high voltage | VIH | 2 | V | 2 | |||
| Input low voltage | VIL | 0.8 | V | 2 | |||
| Input current (DE, RE, DI) | IIN1 | -2 | 2 | uA | 2 | ||
| Input current (A, B) | IIN2 | 40 | 90 | uA | DE=0V, Vcc=5V | 2 | |
| Input current (A, B) | IIN2 | 60 | 100 | uA | VIN=0V | 2 | |
| Receiver differential input threshold voltage | VTH | -200 | -50 | mV | -7V ≤ VCM ≤ +12V | 2 | |
| Receiver differential input threshold hysteresis | ΔVTH | 25 | mV | 2 | |||
| Receiver output high level | VOH | 4 | V | IO=-8mA | 2 | ||
| Receiver output low level | VOL | 0.4 | V | IO=8mA | 2 | ||
| Receiver output leakage current (tri-state) | IOZR | 1 | uA | 0.4V ≤ Vo ≤ 2.4V | 2 | ||
| Receiver input impedance | RIN | 96 | kΩ | -7V ≤ VCM ≤ +12 | 2 | ||
| No load operating current (DE = Vcc) | ICC | 480 | 600 | uA | DE = Vcc; RE = DI = GND or Vcc | 2 | |
| No load operating current (DE = GND) | ICC | 450 | 600 | uA | DE = GND; RE = DI = GND or Vcc | 2 | |
| Receiver output short-circuit current | IOSR | 95 | mA | 0V ≤ VRO ≤ (as printed; limit truncated) | 2 | ||
| ESD protection, human body model | -15 | 15 | kV | Between A/B, human body mode; table also prints ±8 kV | 2 | ||
| Driver input to output (propagation delay high-to-low) | tDPHL | 60 | nS | RDIFF=50Ω, CL1=CL2=100pF, Figure 3,5 | 2 | ||
| Driver input to output (propagation delay low-to-high) | tDPLH | 60 | nS | RDIFF=50Ω, CL1=CL2=100pF, Figure 3,5 | 2 | ||
| Driver output offset | tDPLH, tDPHL | -2.5 | nS | RDIFF=50Ω, CL1=CL2=100pF, Figure 3,5 | 2 | ||
| Driver differential output skew | tDSKEW | -10 | 10 | nS | 2 | ||
| Drive up time | tDR | 25 | nS | 2 | |||
| Drive down time | tDF | 25 | nS | 2 | |||
| Driver enable to high output | tDZH | 150 | nS | CL=100pF, Figure 4,6, S2 closed | 2 | ||
| Driver enable to low output | tDZL | 150 | nS | CL=100pF, Figure 4,6, S1 closed | 2 | ||
| Driver from low to off | tDLZ | 100 | nS | CL=15pF, Figure 4,6, S1 closed | 2 | ||
| Driver from high to off | tDHZ | 100 | nS | CL=15pF, Figure 4,6, S2 closed | 2 | ||
| Receiver input to output (low-to-high) | tRPLH | 150 | nS | /VID/ ≥2.0V; rising and falling time ≤15nS, Figure 7,9 | 2 | ||
| Receiver input to output (high-to-low) | tRPHL | 150 | nS | /VID/ ≥2.0V; rising and falling time ≤15nS, Figure 7,9 | 2 | ||
| Differential receiver offset | tRSKEW | -10 | 0 | 10 | nS | 2 | |
| Receiver enable to output low | tRZL | 20 | 50 | nS | CL=100pF, Figure 2,8 | 2 | |
| Receiver enable to output high | tRZH | 20 | 50 | nS | CL=100pF, Figure 2,8 | 2 | |
| Receiver from low to off | tRLZ | 20 | 50 | nS | CL=100pF, Figure 2,8 | 2 | |
| Receiver from high to off | tRHZ | 20 | 50 | nS | CL=100pF, Figure 2,8 | 2 | |
| Maximum data speed | fMAX | 10 | Mbps | 3 |
CAD (KiCad official)
- Symbol:
HX75176-S - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
hx75176-s-etched.step/hx75176-s-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hx75176-s.step/hx75176-s.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ZHHXDZ datasheet (4 pp, sha256
092e648e6e23b29c, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).