main
Ray
hx6610s: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding)
fbdd1df
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166
{
"slug": "hx6610s",
"version": "0.1.0",
"type": "component",
"description": "HX hengjiaxing Battery Management, ESOP-8. Datasheet-verified pinout, KiCad symbol/footprint/3D.",
"tags": [
"component",
"pmic",
"hx6610s"
],
"dependencies": {},
"hero": {
"type": "image",
"path": "docs/hero.png"
},
"files": [
"page.json",
"README.md",
"hx6610s.kicad_sym",
"hx6610s.kicad_mod",
"hx6610s.glb",
"hx6610s.step",
"hx6610s.lbr",
"docs/hero.png",
"docs/hx6610s-datasheet.pdf",
"viewers/symbol.html",
"viewers/footprint.html",
"hx6610s-etched.step"
],
"visibility": {
"public": true
},
"author": {
"name": "Ray"
},
"component": {
"mpn": "HX6610S",
"manufacturer": "HX hengjiaxing",
"package": "ESOP-8",
"pin_count": 8,
"category": "Battery Management",
"parts": {
"symbol": "hx6610s.kicad_sym",
"footprint": "hx6610s.kicad_mod",
"model_3d": "hx6610s-etched.glb",
"model_3d_plain": "hx6610s.glb",
"model_3d_step": "hx6610s-etched.step",
"model_3d_step_plain": "hx6610s.step",
"lbr": "hx6610s.lbr"
},
"pins": [
{
"number": "1",
"name": "BAT",
"type": "power_out",
"description": "Battery positive terminal. Connects to the Li-ion cell's + terminal; delivers the trickle/CC/CV charge current from the internal PMOSFET. Float voltage is typically 4.22V (Vfloat range 4.18-4.26V). A 1uF bypass capacitor to GND should be placed close to this pin."
},
{
"number": "2",
"name": "Vprog",
"type": "input",
"description": "Float-voltage programming pin. Left open (no R2) gives the default Vfloat = 4.22V. A resistor from Vprog to GND raises the float voltage (R = 2.20*265000/(Vprog-4.20)); a resistor from Vprog to BAT lowers it below 4.2V (R//265000 = (Vprog-2.2)*291500/2.2). Place R2 close to the pin to minimize Vfloat disturbance."
},
{
"number": "3",
"name": "GND",
"type": "power_in",
"description": "Device ground / negative supply reference. All electrical parameters are referenced to this pin (0 V)."
},
{
"number": "4",
"name": "CT",
"type": "input",
"description": "Full-charge shutdown delay setting pin. A capacitor from CT to GND programs the delay before terminating charge / switching the indicator LED, per C = (1.5e-6 * T)/2.2 (e.g. 30 ms delay ≈ 20.5 nF). May be left unconnected when no delay/indicator transition is required."
},
{
"number": "5",
"name": "Iprog",
"type": "input",
"description": "Charge-current programming pin (PROG). A 1% resistor from Iprog to GND sets the constant-current charge current per Ibat = 1200/R (e.g. 6 kΩ ⇒ 200 mA; max programmable ≈ 1 A). Pin voltage is ~0.1 V in trickle mode and ~1 V at full current."
},
{
"number": "6",
"name": "CHRG",
"type": "output",
"description": "Open-drain charge-status indicator. Pulled low (LED on) while the chip is actively charging; high-impedance (LED off) when charging is complete, input is removed, or battery is shorted/reversed. Tie to VDD through an LED+resistor, or to GND if unused."
},
{
"number": "7",
"name": "STDBY",
"type": "output",
"description": "Open-drain standby/full-charge indicator. Pulled low (LED on) when charging is finished or no battery is present; high-impedance while charging is in progress or under fault (short/reverse). Tie to VDD through an LED+resistor, or to GND if unused."
},
{
"number": "8",
"name": "VDD",
"type": "power_in",
"description": "Positive supply input from USB or AC adapter. Operating range 4.5-6 V (absolute max 7 V); OVP trips at 6.2 V and charging stops. UVLO threshold ≈ 3.7 V (200 mV hysteresis). Place a 1 uF bypass capacitor to GND close to this pin."
}
],
"provenance": {
"rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"
},
"viewers": {
"symbol": "viewers/symbol.html",
"footprint": "viewers/footprint.html"
},
"distributor_links": {
"lcsc": "C296208",
"digikey": false,
"mouser": false
},
"distributor_check": {
"checked_at": "2026-10-05T19:01:06Z",
"source": "Component Ocean /api/assign-pns + lcsc_map",
"digikey": {
"pn": null,
"status": "no match"
},
"mouser": {
"pn": null,
"status": "no match"
}
},
"models_3d": [
{
"file": "hx6610s.step",
"role": "plain",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
6,
4.9,
1.75
],
"zmin_mm": 0,
"centre_offset_mm": 0,
"footprint_binding": "identity",
"sha256": "aa1f86df473b51d6fffa82d4ff5a0ca030b07835b04d46a38a7b8cb0f27e418e",
"checked": "2026-10-07",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
},
{
"file": "hx6610s-etched.step",
"role": "eda",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
6,
4.9,
1.75
],
"zmin_mm": 0,
"centre_offset_mm": 0,
"footprint_binding": "identity",
"sha256": "29f7464344e2631c755d61cc75793492e36db5f22c9ed44762dcabd7c317fc20",
"checked": "2026-10-07",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
}
]
}
}