main
Ray
Publish 0.1.0
f7712c1
HV9912NG-G-M901
Microchip Tech · LED Drivers · SOIC-16
HV9912NG-G-M901 from Microchip Tech, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | This pin is the input of the 90V high-voltage linear regulator and withstands up to 90V. |
| 2 | VDD | power_out | This is the supply pin for all internal circuits and must be bypassed to GND with a low-ESR capacitor of at least 0.1 µF; the internal regulator holds it at about 7.75V typical. |
| 3 | GATE | output | This is the output gate driver for an external N-channel power MOSFET, rated at +0.2A source and -0.4A sink. |
| 4 | GND | power_in | This is the ground return for all low-power analog internal circuitry and must be connected to the return path from the input. |
| 5 | CS | input | This pin senses the source current of the external power FET and includes a built-in 100 ns (minimum) blanking time. |
| 6 | SC | passive | This pin sets the slope compensation, with current sourced out of it in the range 0 to 100 µA. |
| 7 | RT | passive | This pin sets the power circuit frequency, where a resistor between RT and GND programs Constant Frequency mode. |
| 8 | SYNC | bidirectional | This I/O pin may be connected to the SYNC pins of other HV9912 devices and causes the oscillators to lock to the highest-frequency oscillator; SYNC input high is at least 2 V and input low is at most 0.8 V. |
| 9 | CLIM | input | This pin provides a programmable input current limit for the converter, set by a resistor divider from the REF pin. |
| 10 | REF | output | This pin provides a 2% accurate reference voltage and must be bypassed to GND with a 0.01 µF to 0.1 µF capacitor. |
| 11 | FAULT | output | This pin is pulled to ground during an output short-circuit or output overvoltage condition and can drive an external MOSFET to disconnect the load in boost converters. |
| 12 | OVP | input | This pin provides overvoltage protection: when the voltage exceeds 5V, GATE is turned off and FAULT goes low, and the IC turns on again when the voltage falls below 4.5V. |
| 13 | PWMD | input | When pulled to GND or left open, switching is disabled, and switching resumes when an external TTL high level is applied. |
| 14 | COMP | passive | This pin connects to a compensation network to GND for stable closed-loop control, and its capacitor also sets the hiccup time. |
| 15 | IREF | input | The voltage at this pin sets the output current level and can be set with a resistor divider from the REF pin. |
| 16 | FDBK | input | This pin provides output current feedback to the controller through a current sense resistor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-16 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input DC Supply Voltage Range | VINDC | 90 | V | DC input voltage (Note 2) | 4 | ||
| Shutdown Mode Supply Current | IINSD | 1.5 | mA | PWMD connected to GND (Note 2) | 4 | ||
| Internally Regulated Voltage | VDD | 7.25 | 7.75 | 8.25 | V | VIN = 9V-90V; PWMD connected to GND (Note 2) | 4 |
| VDD Undervoltage Lockout Threshold (rising) | UVLORISE | 6.5 | 7 | V | VDD rising | 4 | |
| REF Pin Voltage | VREF | 1.225 | 1.25 | 1.285 | V | REF bypassed with a 0.1 µF capacitor to GND; IREF = 0; PWMD = GND; 0°C < TA < +85°C | 4 |
| REF Pin Voltage | VREF | 1.225 | 1.25 | 1.29 | V | REF bypassed with a 0.1 µF capacitor to GND; IREF = 0; PWMD = GND; -40°C < TA < 125°C | 4 |
| Line Regulation of Reference Voltage | VREFLINE | 0 | 20 | mV | REF bypassed with a 0.1 µF capacitor to GND; IREF = 0; VDD = 7.25V-12V; PWMD = GND | 4 | |
| Load Regulation of Reference Voltage | VREFLOAD | 0 | 10 | mV | REF bypassed with a 0.1 µF capacitor to GND; IREF = 0 µA-500 µA; PWMD = GND | 5 | |
| PWMD Input Low Voltage | VPWMD(LO) | 0.8 | V | Note 2 | 5 | ||
| PWMD Input High Voltage | VPWMD(HI) | 2 | V | Note 2 | 5 | ||
| PWMD Pull-down Resistance | RPWMD | 50 | 100 | 150 | kΩ | VPWMD = 5V | 5 |
| GATE Short-circuit Current (source) | ISOURCE | 0.2 | A | VGATE = 0V | 5 | ||
| GATE Sinking Current | ISINK | 0.4 | A | VGATE = VDD | 5 | ||
| GATE Output Rise Time | TRISE | 50 | 85 | ns | CGATE = 1 nF | 5 | |
| GATE Output Fall Time | TFALL | 25 | 45 | ns | CGATE = 1 nF | 5 | |
| Overvoltage Rising Trip Point | VOVP,RISING | 4.75 | 5 | 5.25 | V | OVP rising | 5 |
| Leading Edge Blanking Time | TBLANK | 100 | 280 | ns | 0°C < TA < +85°C | 5 | |
| Leading Edge Blanking Time | TBLANK | 100 | 330 | ns | -40°C < TA < +125°C | 5 | |
| Delay to Output of COMP Comparator | TDELAY1 | 200 | ns | COMP = VDD; CLIM = REF; CSENSE = 0 mV to 600 mV (step up) | 5 | ||
| Delay to Output of CLIMIT Comparator | TDELAY2 | 200 | ns | COMP = VDD; CLIM = 300 mV; CSENSE = 0 mV to 400 mV (step up) | 5 | ||
| Comparator Offset Voltage | VOFFSET | -10 | 10 | mV | 5 | ||
| Open-loop DC Gain (transconductance opamp) | AV | 60 | dB | Output open | 5 | ||
| Input Common Mode Range | VCM | -0.3 | 3 | V | Note 3 | 5 | |
| Output Voltage Range (transconductance opamp) | VO | 0.7 | 6.75 | V | Note 3 | 5 | |
| Transconductance | gM | 450 | 550 | 650 | µA/V | 5 | |
| Input Offset Voltage (transconductance opamp) | VOFFSET | -5 | 5 | mV | 5 | ||
| Input Bias Current | IBIAS | 0.5 | 1 | nA | Note 3 | 5 | |
| Oscillator Frequency | fOSC1 | 99 | 106 | 118 | kHz | RT = 500 kΩ (Note 2) | 5 |
| Oscillator Frequency | fOSC2 | 510 | 580 | 650 | kHz | RT = 96 kΩ (Note 2) | 5 |
| Maximum Duty Cycle | DMAX | 87 | 93 | % | 5 | ||
| SYNC Input High | VSYNCH | 2 | V | 6 | |||
| SYNC Input Low | VSYNCL | 0.8 | V | 6 | |||
| Gain for Short-circuit Comparator | GSC | 1.9 | 2 | 2.1 | V | 6 | |
| Minimum Output Voltage of the Gain Stage | VOMIN | 0.125 | 0.25 | V | 0°C < TA < +85°C; IREF = GND | 6 | |
| Minimum Output Voltage of the Gain Stage | VOMIN | 0.125 | 0.26 | V | -40°C < TA < +125°C; IREF = GND | 6 | |
| Propagation Time for Short-circuit Detection | TOFF | 250 | ns | PWMD = VDD; IREF = 400 mA; FDBK step from 0 mV to 900 mV; FAULT goes from high to low | 6 | ||
| Fault Output Rise Time | TRISE,FAULT | 300 | ns | 330 pF capacitor at FAULT pin | 6 | ||
| Fault Output Fall Time | TFALL,FAULT | 300 | ns | 330 pF capacitor at FAULT pin | 6 | ||
| Blanking Time (short-circuit comparator) | TBLANK,SC | 480 | 900 | ns | 6 | ||
| Current Sourced Out of SC Pin | ISLOPE | 0 | 100 | µA | Note 2 | 6 | |
| Internal Current Mirror Ratio | GSLOPE | 1.8 | 2 | 2.26 | ISLOPE = 50 µA; RSC = 1 kΩ | 6 | |
| Operating Junction Temperature | TJ | -40 | 125 | °C | 6 | ||
| Storage Temperature | Ts | -65 | 150 | °C | 6 | ||
| VIN to GND | VIN | -0.5 | 100 | V | 4 | ||
| VDD to GND | VDD | -0.3 | 13.5 | V | 4 | ||
| CS to GND | CS | -0.3 | V | 4 | |||
| PWMD to GND | PWMD | -0.3 | V | 4 | |||
| GATE to GND | GATE | -0.3 | V | 4 | |||
| All Other Pins to GND | -0.3 | V | 4 | ||||
| Continuous Power Dissipation | 1200 | mW | TA= +25°C | 4 | |||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | 4 | ||
| Storage Temperature Range | -65 | 150 | °C | 4 | |||
| Junction-to-Ambient Thermal Resistance, 16-lead SOIC | θJA | 83 | °C/W | 16-lead SOIC | 6 |
CAD (KiCad official)
- Symbol:
HV9912NG-G-M901 - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files:
hv9912ng-g-m901-etched.step/hv9912ng-g-m901-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hv9912ng-g-m901.step/hv9912ng-g-m901.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (20 pp, sha256
95071e3a782fc328, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# HV9912NG-G-M901
**Microchip Tech** · LED Drivers · SOIC-16
HV9912NG-G-M901 from Microchip Tech, in a SOIC-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | This pin is the input of the 90V high-voltage linear regulator and withstands up to 90V. |
| 2 | VDD | power_out | This is the supply pin for all internal circuits and must be bypassed to GND with a low-ESR capacitor of at least 0.1 µF; the internal regulator holds it at about 7.75V typical. |
| 3 | GATE | output | This is the output gate driver for an external N-channel power MOSFET, rated at +0.2A source and -0.4A sink. |
| 4 | GND | power_in | This is the ground return for all low-power analog internal circuitry and must be connected to the return path from the input. |
| 5 | CS | input | This pin senses the source current of the external power FET and includes a built-in 100 ns (minimum) blanking time. |
| 6 | SC | passive | This pin sets the slope compensation, with current sourced out of it in the range 0 to 100 µA. |
| 7 | RT | passive | This pin sets the power circuit frequency, where a resistor between RT and GND programs Constant Frequency mode. |
| 8 | SYNC | bidirectional | This I/O pin may be connected to the SYNC pins of other HV9912 devices and causes the oscillators to lock to the highest-frequency oscillator; SYNC input high is at least 2 V and input low is at most 0.8 V. |
| 9 | CLIM | input | This pin provides a programmable input current limit for the converter, set by a resistor divider from the REF pin. |
| 10 | REF | output | This pin provides a 2% accurate reference voltage and must be bypassed to GND with a 0.01 µF to 0.1 µF capacitor. |
| 11 | FAULT | output | This pin is pulled to ground during an output short-circuit or output overvoltage condition and can drive an external MOSFET to disconnect the load in boost converters. |
| 12 | OVP | input | This pin provides overvoltage protection: when the voltage exceeds 5V, GATE is turned off and FAULT goes low, and the IC turns on again when the voltage falls below 4.5V. |
| 13 | PWMD | input | When pulled to GND or left open, switching is disabled, and switching resumes when an external TTL high level is applied. |
| 14 | COMP | passive | This pin connects to a compensation network to GND for stable closed-loop control, and its capacitor also sets the hiccup time. |
| 15 | IREF | input | The voltage at this pin sets the output current level and can be set with a resistor divider from the REF pin. |
| 16 | FDBK | input | This pin provides output current feedback to the controller through a current sense resistor. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-16 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input DC Supply Voltage Range | VINDC | | | 90 | V | DC input voltage (Note 2) | 4 |
| Shutdown Mode Supply Current | IINSD | | | 1.5 | mA | PWMD connected to GND (Note 2) | 4 |
| Internally Regulated Voltage | VDD | 7.25 | 7.75 | 8.25 | V | VIN = 9V-90V; PWMD connected to GND (Note 2) | 4 |
| VDD Undervoltage Lockout Threshold (rising) | UVLORISE | 6.5 | | 7 | V | VDD rising | 4 |
| REF Pin Voltage | VREF | 1.225 | 1.25 | 1.285 | V | REF bypassed with a 0.1 µF capacitor to GND; IREF = 0; PWMD = GND; 0°C < TA < +85°C | 4 |
| REF Pin Voltage | VREF | 1.225 | 1.25 | 1.29 | V | REF bypassed with a 0.1 µF capacitor to GND; IREF = 0; PWMD = GND; -40°C < TA < 125°C | 4 |
| Line Regulation of Reference Voltage | VREFLINE | 0 | | 20 | mV | REF bypassed with a 0.1 µF capacitor to GND; IREF = 0; VDD = 7.25V-12V; PWMD = GND | 4 |
| Load Regulation of Reference Voltage | VREFLOAD | 0 | | 10 | mV | REF bypassed with a 0.1 µF capacitor to GND; IREF = 0 µA-500 µA; PWMD = GND | 5 |
| PWMD Input Low Voltage | VPWMD(LO) | | | 0.8 | V | Note 2 | 5 |
| PWMD Input High Voltage | VPWMD(HI) | 2 | | | V | Note 2 | 5 |
| PWMD Pull-down Resistance | RPWMD | 50 | 100 | 150 | kΩ | VPWMD = 5V | 5 |
| GATE Short-circuit Current (source) | ISOURCE | 0.2 | | | A | VGATE = 0V | 5 |
| GATE Sinking Current | ISINK | 0.4 | | | A | VGATE = VDD | 5 |
| GATE Output Rise Time | TRISE | | 50 | 85 | ns | CGATE = 1 nF | 5 |
| GATE Output Fall Time | TFALL | | 25 | 45 | ns | CGATE = 1 nF | 5 |
| Overvoltage Rising Trip Point | VOVP,RISING | 4.75 | 5 | 5.25 | V | OVP rising | 5 |
| Leading Edge Blanking Time | TBLANK | 100 | | 280 | ns | 0°C < TA < +85°C | 5 |
| Leading Edge Blanking Time | TBLANK | 100 | | 330 | ns | -40°C < TA < +125°C | 5 |
| Delay to Output of COMP Comparator | TDELAY1 | | | 200 | ns | COMP = VDD; CLIM = REF; CSENSE = 0 mV to 600 mV (step up) | 5 |
| Delay to Output of CLIMIT Comparator | TDELAY2 | | | 200 | ns | COMP = VDD; CLIM = 300 mV; CSENSE = 0 mV to 400 mV (step up) | 5 |
| Comparator Offset Voltage | VOFFSET | -10 | | 10 | mV | | 5 |
| Open-loop DC Gain (transconductance opamp) | AV | 60 | | | dB | Output open | 5 |
| Input Common Mode Range | VCM | -0.3 | | 3 | V | Note 3 | 5 |
| Output Voltage Range (transconductance opamp) | VO | 0.7 | | 6.75 | V | Note 3 | 5 |
| Transconductance | gM | 450 | 550 | 650 | µA/V | | 5 |
| Input Offset Voltage (transconductance opamp) | VOFFSET | -5 | | 5 | mV | | 5 |
| Input Bias Current | IBIAS | | 0.5 | 1 | nA | Note 3 | 5 |
| Oscillator Frequency | fOSC1 | 99 | 106 | 118 | kHz | RT = 500 kΩ (Note 2) | 5 |
| Oscillator Frequency | fOSC2 | 510 | 580 | 650 | kHz | RT = 96 kΩ (Note 2) | 5 |
| Maximum Duty Cycle | DMAX | 87 | | 93 | % | | 5 |
| SYNC Input High | VSYNCH | 2 | | | V | | 6 |
| SYNC Input Low | VSYNCL | | | 0.8 | V | | 6 |
| Gain for Short-circuit Comparator | GSC | 1.9 | 2 | 2.1 | V | | 6 |
| Minimum Output Voltage of the Gain Stage | VOMIN | 0.125 | | 0.25 | V | 0°C < TA < +85°C; IREF = GND | 6 |
| Minimum Output Voltage of the Gain Stage | VOMIN | 0.125 | | 0.26 | V | -40°C < TA < +125°C; IREF = GND | 6 |
| Propagation Time for Short-circuit Detection | TOFF | | | 250 | ns | PWMD = VDD; IREF = 400 mA; FDBK step from 0 mV to 900 mV; FAULT goes from high to low | 6 |
| Fault Output Rise Time | TRISE,FAULT | | | 300 | ns | 330 pF capacitor at FAULT pin | 6 |
| Fault Output Fall Time | TFALL,FAULT | | | 300 | ns | 330 pF capacitor at FAULT pin | 6 |
| Blanking Time (short-circuit comparator) | TBLANK,SC | 480 | | 900 | ns | | 6 |
| Current Sourced Out of SC Pin | ISLOPE | 0 | | 100 | µA | Note 2 | 6 |
| Internal Current Mirror Ratio | GSLOPE | 1.8 | 2 | 2.26 | | ISLOPE = 50 µA; RSC = 1 kΩ | 6 |
| Operating Junction Temperature | TJ | -40 | | 125 | °C | | 6 |
| Storage Temperature | Ts | -65 | | 150 | °C | | 6 |
| VIN to GND | VIN | -0.5 | | 100 | V | | 4 |
| VDD to GND | VDD | -0.3 | | 13.5 | V | | 4 |
| CS to GND | CS | -0.3 | | | V | | 4 |
| PWMD to GND | PWMD | -0.3 | | | V | | 4 |
| GATE to GND | GATE | -0.3 | | | V | | 4 |
| All Other Pins to GND | | -0.3 | | | V | | 4 |
| Continuous Power Dissipation | | | | 1200 | mW | TA= +25°C | 4 |
| Operating Junction Temperature Range | TJ | -40 | | 125 | °C | | 4 |
| Storage Temperature Range | | -65 | | 150 | °C | | 4 |
| Junction-to-Ambient Thermal Resistance, 16-lead SOIC | θJA | | 83 | | °C/W | 16-lead SOIC | 6 |
## CAD (KiCad official)
- Symbol: `HV9912NG-G-M901`
- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`
- 3D model: SOIC-16 (KiCad packages3D, STEP)
- 3D model files: `hv9912ng-g-m901-etched.step` / `hv9912ng-g-m901-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `hv9912ng-g-m901.step` / `hv9912ng-g-m901.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/hv9912ng-g-m901-datasheet.pdf) (20 pp, sha256 `95071e3a782fc328`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/hv9912ng-g-m901-datasheet.pdf)