main
Ray hr1001cgs-z: component.models_3d pose record per STEP (Z-up, seated z=0, pad-centre origin, identity binding) 929ff7e
{
  "schema_version": 1,
  "type": "component",
  "slug": "hr1001cgs-z",
  "title": "HR1001CGS-Z",
  "brief": "Monolithic Power Systems AC-DC Controllers And Regulators, SOIC-16. Pinout extracted from the datasheet, KiCad symbol/footprint/3D.",
  "version": "0.1.0",
  "license": "CC-BY-SA-4.0",
  "tags": [
    "component",
    "power management (pmic)",
    "hr1001cgs-z"
  ],
  "component": {
    "mpn": "HR1001CGS-Z",
    "manufacturer": "Monolithic Power Systems",
    "package": "SOIC-16",
    "pin_count": 16,
    "category": "Power Management (PMIC)",
    "subcategory": "AC-DC Controllers And Regulators",
    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603388520325537792",
    "parts": {
      "symbol": "hr1001cgs-z.kicad_sym",
      "footprint": "hr1001cgs-z.kicad_mod",
      "model_3d": "hr1001cgs-z-etched.glb",
      "model_3d_plain": "hr1001cgs-z.glb",
      "model_3d_step": "hr1001cgs-z-etched.step",
      "model_3d_step_plain": "hr1001cgs-z.step",
      "lbr": "hr1001cgs-z.lbr"
    },
    "distributor_links": {},
    "pins": [
      {
        "number": "1",
        "name": "SS",
        "type": "passive",
        "description": "Soft start. Connect an external capacitor from SS to GND and a resistor to FSET to program the maximum oscillator frequency and the frequency-shift time constant during start-up. An internal switch discharges this capacitor when the chip turns off (VCC < UVLO, BO fault, LATCH tripped, CS > VCS-OCP, TIMER > VTIMER-fmax, or thermal shutdown) to guarantee a soft start on the next cycle."
      },
      {
        "number": "2",
        "name": "TIMER",
        "type": "passive",
        "description": "Over-current-to-shutdown period. A capacitor and resistor from TIMER to GND set the maximum duration allowed in over-current before the IC stops switching and the delay before it resumes. An internal current source ITIMER charges the capacitor whenever VCS > VCS-OCR; the external resistor discharges it slowly. Reaching VTIMER-fmax forces the SS cap to fully discharge (freq → max); exceeding VTIMER-SD halts switching until the voltage decays below VTIMER-R, when the IC re-enters soft start."
      },
      {
        "number": "3",
        "name": "CT",
        "type": "passive",
        "description": "Oscillator timing capacitor. An internal current source (programmed by the network on FSET) alternately charges and discharges a capacitor tied from CT to GND between VCFp and VCFv thresholds, setting the converter's switching frequency."
      },
      {
        "number": "4",
        "name": "FSET",
        "type": "passive",
        "description": "Switching frequency set / precise 2 V reference. A resistor from FSET to GND defines the current that sets the minimum oscillator frequency. Tying the optocoupler phototransistor to FSET through a resistor closes the feedback loop that modulates the oscillator and regulates the output; that resistor's value sets the maximum operating frequency. An R-C series from FSET to GND sets the start-up frequency shift to limit inrush energy. Source current rating 2 mA max."
      },
      {
        "number": "5",
        "name": "BURST",
        "type": "input",
        "description": "Burst-mode threshold. BURST senses the feedback-related voltage and is compared to an internal VBurst reference. Below VBurst the IC enters an idle low-Iq state; when feedback drives BURST above VBurst + 30 mV (VBurst-hys) switching resumes with no soft start. This enables light-load burst operation whose entry point is set by a resistor from the optocoupler to FSET. Tie BURST to FSET if burst mode is not used."
      },
      {
        "number": "6",
        "name": "CS",
        "type": "input",
        "description": "Half-bridge current sense (also used for CMP). Sensed via a resistor or capacitive divider on the primary. Three functions: (1) over-current regulation - VCS > VCS-OCR discharges SS and pushes frequency up; (2) over-current protection - VCS > VCS-OCP with VSS < VSS-OCP latches OCP off (cleared by cycling VCC below UVLO); (3) capacitive-mode protection - CS is compared to VCSNR/VCSPR after each gate turn-off to block the opposite gate until the correct dV/dt slope is detected or the CMP timer expires. Absolute rating −3 V to +6 V. Tie CS to GND if CMP is not used."
      },
      {
        "number": "7",
        "name": "BO",
        "type": "input",
        "description": "Input voltage sense and brown-in/brown-out protection. When BO rises above VBO-On the IC enables the gate drivers; when BO falls below VBO-Off the IC is disabled. Also supports remote on/off."
      },
      {
        "number": "8",
        "name": "LATCH",
        "type": "input",
        "description": "IC latched shutdown input. When VLATCH is exceeded the IC shuts down and drops its bias current near the pre-start-up level. Reset only when VCC is discharged below its UVLO threshold. Connect LATCH to GND if not used."
      },
      {
        "number": "9",
        "name": "HBVS",
        "type": "input",
        "description": "Half-bridge dV/dt sense for adaptive dead-time. A high-voltage capacitor is tied between SW and HBVS; the dV/dt current through HBVS is measured to adaptively adjust the dead time between HG and LG. Sink current ±65 mA max."
      },
      {
        "number": "10",
        "name": "GND",
        "type": "power_in",
        "description": "Ground. Return for the low-side gate driver and the IC bias. Route separate traces from GND to the signal ground and to the pulsed gate-current return."
      },
      {
        "number": "11",
        "name": "LG",
        "type": "output",
        "description": "Low-side gate driver output. Push-pull driver with ±0.8 A peak source/sink to drive the low-side half-bridge MOSFET. Held at GND during UVLO. Voltage rating −0.3 V to VCC."
      },
      {
        "number": "12",
        "name": "VCC",
        "type": "power_in",
        "description": "Supply voltage for the IC bias and the low-side gate driver. Recommended operating range 13 V to 15.5 V (self-limited internally). Decouple with a small (e.g. 0.1 µF) bypass capacitor at the pin."
      },
      {
        "number": "13",
        "name": "NC",
        "type": "unconnected",
        "description": "High-voltage spacer. No internal connection. Provided to isolate the high-voltage SW pin from the low-voltage side and to ease safety-agency creepage-distance compliance on the PCB."
      },
      {
        "number": "14",
        "name": "SW",
        "type": "power_in",
        "description": "High-side driver source / half-bridge switching node return. Current return for the high-side gate drive. Requires careful layout to avoid large negative spikes below GND. Rated −3 V to +600 V with a maximum dV/dt of 50 V/ns."
      },
      {
        "number": "15",
        "name": "HG",
        "type": "output",
        "description": "High-side floating gate driver output. Push-pull driver with ±0.8 A peak source/sink to drive the upper half-bridge MOSFET, referenced to SW. An internal pull-down resistor to SW prevents HG from floating during UVLO."
      },
      {
        "number": "16",
        "name": "BST",
        "type": "power_in",
        "description": "Bootstrap supply for the floating high-side gate driver. Connect a bootstrap capacitor between BST and SW; it is charged by an internal bootstrap diode driven in phase with the low-side gate driver. Absolute rating −0.3 V to +618 V."
      }
    ],
    "provenance": {
      "extractor": "ds2sf",
      "datasheet": {
        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603388520325537792",
        "pages": null,
        "sha256": "05a190f3b063515a",
        "source_tier": "lcsc"
      },
      "cad": "KiCad official (CC-BY-SA 4.0)",
      "pins": {
        "total": 16,
        "described": 16,
        "cites_pages": true,
        "refuses_to_fabricate": true
      }
    },
    "viewers": {
      "symbol": "viewers/symbol.html",
      "footprint": "viewers/footprint.html"
    },
    "models_3d": [
      {
        "file": "hr1001cgs-z.step",
        "role": "plain",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          6,
          9.9,
          1.75
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "d5eeddb4c0b304dc61950919b126fc61d7586abd5f16ab71a2a79759ec6498bf",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      },
      {
        "file": "hr1001cgs-z-etched.step",
        "role": "eda",
        "up": "Z",
        "units": "mm",
        "origin": "footprint origin = pad-pattern centre",
        "seat": "z = 0",
        "extents_mm": [
          6,
          9.9,
          1.75
        ],
        "zmin_mm": 0,
        "centre_offset_mm": 0,
        "footprint_binding": "identity",
        "sha256": "fa1bdad096db0d2caa2e3ade529f6770932d26109cb8febac003fa7f081d6afa",
        "checked": "2026-10-07",
        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
      }
    ]
  },
  "metadata": {
    "specs": {
      "Manufacturer": "Monolithic Power Systems",
      "Package": "SOIC-16",
      "Category": "Power Management (PMIC)",
      "Pins": "16"
    }
  },
  "variants": [
    {
      "mpn": "HR1001CGS-Z",
      "kind": "packaging"
    }
  ],
  "sections": [
    "hero",
    "viewers",
    "readme",
    "breadcrumbs",
    "info"
  ],
  "discovery_triggers": [
    "hr1001cgs-z"
  ],
  "discovery_pitch": "HR1001CGS-Z (Monolithic Power Systems) component page with datasheet-verified CAD.",
  "author": {
    "name": "Ray"
  },
  "dependencies": {},
  "hero": {
    "type": "image",
    "path": "docs/hero.png"
  },
  "files": [
    "page.json",
    "README.md",
    "hr1001cgs-z.kicad_sym",
    "hr1001cgs-z.kicad_mod",
    "hr1001cgs-z.glb",
    "hr1001cgs-z.step",
    "hr1001cgs-z.lbr",
    "docs/hero.png",
    "docs/hr1001cgs-z-datasheet.pdf",
    "viewers/symbol.html",
    "viewers/footprint.html"
  ],
  "visibility": {
    "public": true
  },
  "updated_at": "2026-09-24T21:58:24.331Z"
}