main
Ray
Publish 0.1.0
25e1060
HI7191IBZ
RENESAS · Analog To Digital Converters (ADCs) · SOIC-20-300mil
HI7191IBZ from RENESAS, in a SOIC-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCLK | bidirectional | Serial interface clock that synchronizes serial data transfers (input in external clocking mode, output at OSC1/8 in self-clocking mode, up to 5MHz external); data is input on the rising edge and output on the falling edge. |
| 2 | SDO | tri_state | Serial Data OUT, read line for 3-wire protocols such as Motorola SPI; high impedance when SDIO is used bidirectionally or when CS is high. |
| 3 | SDIO | bidirectional | Serial Data IN or OUT, bidirectional programmable line that interfaces directly to the Intel standard serial interface using a 2-wire protocol. |
| 4 | CS | input | Active-low chip select input that selects the HI7191 for a serial data transfer cycle; can be tied to DGND. |
| 5 | DRDY | output | Active-low interrupt output indicating a new data word is available for reading. |
| 6 | DGND | power_in | Digital supply ground. |
| 7 | AVSS | power_in | Negative analog power supply (-5V). |
| 8 | VRLO | input | External reference input, should be negative referenced to VRHI. |
| 9 | VRHI | input | External reference input, should be positive referenced to VRLO. |
| 10 | VCM | input | Common mode input, should be set halfway between AVDD and AVSS. |
| 11 | VINLO | input | Analog input LO, the negative input of the PGIA. |
| 12 | VINHI | input | Analog input HI, the positive input of the PGIA, connected to a transducer burn-out current source controlled via the Control Register. |
| 13 | AVDD | power_in | Positive analog power supply (+5V). |
| 14 | AGND | power_in | Analog supply ground. |
| 15 | DVDD | power_in | Positive digital supply (+5V). |
| 16 | OSC2 | passive | Used to connect a crystal between OSC1 and OSC2; leave open otherwise. |
| 17 | OSC1 | input | Oscillator clock input, driven by a crystal across OSC1/OSC2 or an external oscillator; frequency should be 10MHz (Typ). |
| 18 | RESET | input | Active-low reset used to initialize the HI7191 registers, filter and state machines. |
| 19 | SYNC | input | Active-low sync input used to synchronize multiple HI7191s; a logic 0 initializes the converter. |
| 20 | MODE | input | Selects Synchronous Self Clocking (Mode = 1) or Synchronous External Clocking (Mode = 0) for the serial port. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | SOIC-20-300mil |
| Category | Data Converters |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Integral Non-Linearity | INL | 0.0015 | 0.003 | %FS | End Point Line Method (Notes 3, 5, 6) | 4 | |
| Normal Mode 50Hz Rejection | 120 | dB | Filter Notch = 10Hz, 25Hz, 50Hz (Note 2) | 4 | |||
| Normal Mode 60Hz Rejection | 120 | dB | Filter Notch = 10Hz, 30Hz, 60Hz (Note 2) | 4 | |||
| Step Response Settling Time | 2 | 4 | Conversions | 4 | |||
| Input Leakage Current | IIN | 1 | nA | VIN = AVDD (Note 2) | 4 | ||
| Reference Voltage Range | VREF | 2.5 | 5 | V | VREF = VRHI - VRLO | 4 | |
| Input Span | 0.2 | 2.4 | x (VREF/Gain) | 4 | |||
| Input Logic High Voltage | VIH | 2 | V | Note 11 | 4 | ||
| Input Logic Low Voltage | VIL | 0.8 | V | 4 | |||
| Input Logic Current | II | 1 | 10 | µA | VIN = 0V, +5V | 5 | |
| Output Logic High Voltage | VOH | 2.4 | V | IOUT = -100µA (Note 7) | 5 | ||
| Output Logic Low Voltage | VOL | 0.4 | V | IOUT = 3mA (Note 7) | 5 | ||
| Output Three-State Leakage Current | IOZ | -10 | 1 | 10 | µA | VOUT = 0V, +5V (Note 7) | 5 |
| SCLK Minimum Cycle Time | tSCLK | 200 | ns | 5 | |||
| SCLK Minimum Pulse Width | tSCLKPW | 50 | ns | 5 | |||
| CS to SCLK Precharge Time | tPRE | 50 | ns | 5 | |||
| DRDY Minimum High Pulse Width | 500 | ns | Notes 2, 7 | 5 | |||
| Data Setup to SCLK Rising Edge (Write) | tDSU | 50 | ns | 5 | |||
| Data Hold from SCLK Rising Edge (Write) | tDHLD | 0 | ns | 5 | |||
| Data Read Access from Instruction Byte Write | tACC | 40 | ns | Note 7 | 5 | ||
| Read Bit Valid from SCLK Falling Edge | tDV | 40 | ns | Note 7 | 5 | ||
| RESET Low Pulse Width | 100 | ns | Note 2 | 5 | |||
| SYNC Low Pulse Width | 100 | ns | Note 2 | 5 | |||
| Oscillator Clock Frequency | 0.1 | 10 | MHz | Note 2 | 5 | ||
| Output Rise/Fall Time | 30 | ns | Note 2 | 5 | |||
| Input Rise/Fall Time | 1 | µs | Note 2 | 5 | |||
| Supply Current AVDD | IAVDD | 1.5 | mA | 5 | |||
| Supply Current AVSS | IAVSS | 2 | mA | 5 | |||
| Supply Current DVDD | IDVDD | 3 | mA | SCLK = 4MHz | 5 | ||
| Power Dissipation, Active | PDA | 15 | 32.5 | mW | SB = '0' | 5 | |
| Operating Temperature Range | -40 | 85 | °C | 4 | |||
| AVDD to AGND | 5.5 | V | 4 | ||||
| AVSS to AGND | -5.5 | V | 4 | ||||
| DVDD to DGND | 5.5 | V | 4 | ||||
| DGND to AGND | 0.3 | V | 4 | ||||
| Maximum Junction Temperature | 150 | °C | Plastic Packages | 4 | |||
| Storage Temperature Range | -65 | 150 | °C | 4 | |||
| Lead Temperature (Soldering) | 300 | °C | 10s, SOIC lead tips only | 4 | |||
| ESD Human Body Model | 500 | V | No damage | 4 | |||
| Thermal Resistance, SOIC | θJA | 75 | °C/W | Typical, Note 1 | 4 | ||
| Common Mode Rejection Ratio | CMRR | 70 | dB | VCM = 0V, VINHI = VINLO from -2V to +2V | 4 | ||
| Offset Error Drift | 1 | µV/°C | VINHI = VINLO (Notes 3, 8) | 4 | |||
| Input Capacitance (analog) | CIN | 5 | pF | 4 | |||
| Transducer Burn-Out Current | IBO | 200 | nA | 4 | |||
| Power Dissipation, Standby | PDS | 5 | mW | SB = '1' | 5 | ||
| PSRR | PSRR | 70 | dB | Note 3 | 5 |
CAD (KiCad official)
- Symbol:
HI7191IBZ - Footprint:
Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm - 3D model: SOIC-20-300mil (KiCad packages3D, STEP)
- 3D model files:
hi7191ibz-etched.step/hi7191ibz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);hi7191ibz.step/hi7191ibz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: RENESAS datasheet (25 pp, sha256
3b76cd97ef520f04, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# HI7191IBZ
**RENESAS** · Analog To Digital Converters (ADCs) · SOIC-20-300mil
HI7191IBZ from RENESAS, in a SOIC-20-300mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCLK | bidirectional | Serial interface clock that synchronizes serial data transfers (input in external clocking mode, output at OSC1/8 in self-clocking mode, up to 5MHz external); data is input on the rising edge and output on the falling edge. |
| 2 | SDO | tri_state | Serial Data OUT, read line for 3-wire protocols such as Motorola SPI; high impedance when SDIO is used bidirectionally or when CS is high. |
| 3 | SDIO | bidirectional | Serial Data IN or OUT, bidirectional programmable line that interfaces directly to the Intel standard serial interface using a 2-wire protocol. |
| 4 | CS | input | Active-low chip select input that selects the HI7191 for a serial data transfer cycle; can be tied to DGND. |
| 5 | DRDY | output | Active-low interrupt output indicating a new data word is available for reading. |
| 6 | DGND | power_in | Digital supply ground. |
| 7 | AVSS | power_in | Negative analog power supply (-5V). |
| 8 | VRLO | input | External reference input, should be negative referenced to VRHI. |
| 9 | VRHI | input | External reference input, should be positive referenced to VRLO. |
| 10 | VCM | input | Common mode input, should be set halfway between AVDD and AVSS. |
| 11 | VINLO | input | Analog input LO, the negative input of the PGIA. |
| 12 | VINHI | input | Analog input HI, the positive input of the PGIA, connected to a transducer burn-out current source controlled via the Control Register. |
| 13 | AVDD | power_in | Positive analog power supply (+5V). |
| 14 | AGND | power_in | Analog supply ground. |
| 15 | DVDD | power_in | Positive digital supply (+5V). |
| 16 | OSC2 | passive | Used to connect a crystal between OSC1 and OSC2; leave open otherwise. |
| 17 | OSC1 | input | Oscillator clock input, driven by a crystal across OSC1/OSC2 or an external oscillator; frequency should be 10MHz (Typ). |
| 18 | RESET | input | Active-low reset used to initialize the HI7191 registers, filter and state machines. |
| 19 | SYNC | input | Active-low sync input used to synchronize multiple HI7191s; a logic 0 initializes the converter. |
| 20 | MODE | input | Selects Synchronous Self Clocking (Mode = 1) or Synchronous External Clocking (Mode = 0) for the serial port. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | RENESAS |
| Package | SOIC-20-300mil |
| Category | Data Converters |
| Pins | 20 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Integral Non-Linearity | INL | | 0.0015 | 0.003 | %FS | End Point Line Method (Notes 3, 5, 6) | 4 |
| Normal Mode 50Hz Rejection | | 120 | | | dB | Filter Notch = 10Hz, 25Hz, 50Hz (Note 2) | 4 |
| Normal Mode 60Hz Rejection | | 120 | | | dB | Filter Notch = 10Hz, 30Hz, 60Hz (Note 2) | 4 |
| Step Response Settling Time | | | 2 | 4 | Conversions | | 4 |
| Input Leakage Current | IIN | | | 1 | nA | VIN = AVDD (Note 2) | 4 |
| Reference Voltage Range | VREF | 2.5 | | 5 | V | VREF = VRHI - VRLO | 4 |
| Input Span | | 0.2 | | 2.4 | | x (VREF/Gain) | 4 |
| Input Logic High Voltage | VIH | 2 | | | V | Note 11 | 4 |
| Input Logic Low Voltage | VIL | | | 0.8 | V | | 4 |
| Input Logic Current | II | | 1 | 10 | µA | VIN = 0V, +5V | 5 |
| Output Logic High Voltage | VOH | 2.4 | | | V | IOUT = -100µA (Note 7) | 5 |
| Output Logic Low Voltage | VOL | | | 0.4 | V | IOUT = 3mA (Note 7) | 5 |
| Output Three-State Leakage Current | IOZ | -10 | 1 | 10 | µA | VOUT = 0V, +5V (Note 7) | 5 |
| SCLK Minimum Cycle Time | tSCLK | 200 | | | ns | | 5 |
| SCLK Minimum Pulse Width | tSCLKPW | 50 | | | ns | | 5 |
| CS to SCLK Precharge Time | tPRE | 50 | | | ns | | 5 |
| DRDY Minimum High Pulse Width | | 500 | | | ns | Notes 2, 7 | 5 |
| Data Setup to SCLK Rising Edge (Write) | tDSU | 50 | | | ns | | 5 |
| Data Hold from SCLK Rising Edge (Write) | tDHLD | 0 | | | ns | | 5 |
| Data Read Access from Instruction Byte Write | tACC | | | 40 | ns | Note 7 | 5 |
| Read Bit Valid from SCLK Falling Edge | tDV | | | 40 | ns | Note 7 | 5 |
| RESET Low Pulse Width | | 100 | | | ns | Note 2 | 5 |
| SYNC Low Pulse Width | | 100 | | | ns | Note 2 | 5 |
| Oscillator Clock Frequency | | 0.1 | | 10 | MHz | Note 2 | 5 |
| Output Rise/Fall Time | | | | 30 | ns | Note 2 | 5 |
| Input Rise/Fall Time | | | | 1 | µs | Note 2 | 5 |
| Supply Current AVDD | IAVDD | | | 1.5 | mA | | 5 |
| Supply Current AVSS | IAVSS | | | 2 | mA | | 5 |
| Supply Current DVDD | IDVDD | | | 3 | mA | SCLK = 4MHz | 5 |
| Power Dissipation, Active | PDA | | 15 | 32.5 | mW | SB = '0' | 5 |
| Operating Temperature Range | | -40 | | 85 | °C | | 4 |
| AVDD to AGND | | | | 5.5 | V | | 4 |
| AVSS to AGND | | -5.5 | | | V | | 4 |
| DVDD to DGND | | | | 5.5 | V | | 4 |
| DGND to AGND | | | | 0.3 | V | | 4 |
| Maximum Junction Temperature | | | | 150 | °C | Plastic Packages | 4 |
| Storage Temperature Range | | -65 | | 150 | °C | | 4 |
| Lead Temperature (Soldering) | | | | 300 | °C | 10s, SOIC lead tips only | 4 |
| ESD Human Body Model | | | | 500 | V | No damage | 4 |
| Thermal Resistance, SOIC | θJA | | 75 | | °C/W | Typical, Note 1 | 4 |
| Common Mode Rejection Ratio | CMRR | | 70 | | dB | VCM = 0V, VINHI = VINLO from -2V to +2V | 4 |
| Offset Error Drift | | | 1 | | µV/°C | VINHI = VINLO (Notes 3, 8) | 4 |
| Input Capacitance (analog) | CIN | | 5 | | pF | | 4 |
| Transducer Burn-Out Current | IBO | | 200 | | nA | | 4 |
| Power Dissipation, Standby | PDS | | 5 | | mW | SB = '1' | 5 |
| PSRR | PSRR | | 70 | | dB | Note 3 | 5 |
## CAD (KiCad official)
- Symbol: `HI7191IBZ`
- Footprint: `Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm`
- 3D model: SOIC-20-300mil (KiCad packages3D, STEP)
- 3D model files: `hi7191ibz-etched.step` / `hi7191ibz-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `hi7191ibz.step` / `hi7191ibz.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [RENESAS datasheet](docs/hi7191ibz-datasheet.pdf) (25 pp, sha256 `3b76cd97ef520f04`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/hi7191ibz-datasheet.pdf)