main
History Download
Ray Publish 0.1.0 ec7993b

HG24C04CM

HGSEMI · EEPROM · SOP-8

HG24C04CM from HGSEMI, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No connect pin; the datasheet pin diagram shows pin 1 as NC and gives no function for it.
2 E1 input Device address input that can be tied to VCC or GND in any combination, and is internally pulled down to GND if left floating.
3 E2 input Device address input that can be tied to VCC or GND in any combination, and is internally pulled down to GND if left floating.
4 GND power_in Ground reference for the power supply, to be connected to system ground.
5 SDA bidirectional Serial data pin, an open-drain bidirectional input/output used to transfer data to and from the device.
6 SCL input Serial clock input that controls data flow, with input data latched on the rising edge and output data clocked out on the falling edge of SCL.
7 WP input Write protection input that makes the memory read-only when tied to VCC, enables writes when tied to GND, and is internally pulled down to GND if left floating.
8 VCC power_in Device power supply pin, with a supply range of 1.7V to 5.5V.

Key specifications

Parameter Value
Manufacturer HGSEMI
Package SOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Read supply current at 1MHz, VCC=1.7V ICC1 0.1 mA VCC=1.7V, Read at 1MHz 18
Read supply current at 400kHz, VCC=5.5V ICC1 0.4 mA VCC=5.5V, Read at 400 kHz 18
Read supply current at 1MHz, VCC=5.5V ICC1 0.5 mA VCC=5.5V, Read at 1MHz 18
Write supply current ICC2 1 mA VCC=5.5V, Write at 400 kHz 18
Standby current ISB 1 μA VCC = 1.7V, VIN = VCC or GND 18
Input leakage current ILI 1 μA VIN = VCC or GND 18
Output leakage current ILO 1 μA VOUT = VCC or GND 18
Input low-level voltage (SDA, SCL) VIL -0.5 0.3 V Max printed as 0.3*VCC 18
Input high-level voltage (SDA, SCL) VIH 0.7 5.5 V Min printed as 0.7*VCC; max printed as VCC+0.5 (value shown is the VCC max of 5.5 V range, not the +0.5 offset) 18
Low-level output voltage VOL1 0.4 V VCC > 2V, IOL= 3mA 18
Low-level output voltage VOL2 0.2 V VCC ≤ 2V, IOL= 2mA 18
Clock frequency, SCL (Fast) fSCL 400 kHz Fast, VCC = 1.7V to 5.5V 19
Clock frequency, SCL (High Speed) fSCL 1000 kHz High Speed, VCC = 1.7V to 5.5V 19
Clock pulse width low (Fast) tLOW 1300 ns Fast, VCC = 1.7V to 5.5V 19
Clock pulse width low (High Speed) tLOW 600 ns High Speed, VCC = 1.7V to 5.5V 19
Clock pulse width high (Fast) tHIGH 600 ns Fast, VCC = 1.7V to 5.5V 19
Clock pulse width high (High Speed) tHIGH 260 ns High Speed, VCC = 1.7V to 5.5V 19
SDA rise time (Fast) tR 300 ns Fast; ensured by characterization only (note 1) 19
SDA rise time (High Speed) tR 300 ns High Speed; ensured by characterization only (note 1) 19
SDA(Out) fall time (Fast) tF 300 ns Fast; ensured by characterization only (note 1) 19
SDA(Out) fall time (High Speed) tF 100 ns High Speed; ensured by characterization only (note 1) 19
Start hold time (Fast) tHD.STA 600 ns Fast, VCC = 1.7V to 5.5V 19
Start hold time (High Speed) tHD.STA 250 ns High Speed, VCC = 1.7V to 5.5V 19
Start setup time (Fast) tSU.STA 600 ns Fast, VCC = 1.7V to 5.5V 19
Start setup time (High Speed) tSU.STA 250 ns High Speed, VCC = 1.7V to 5.5V 19
Stop setup time (Fast) tSU.STO 600 ns Fast, VCC = 1.7V to 5.5V 19
Stop setup time (High Speed) tSU.STO 250 ns High Speed, VCC = 1.7V to 5.5V 19
Bus free time between Stop and Start (Fast) tBUF 1300 ns Fast, VCC = 1.7V to 5.5V 19
Bus free time between Stop and Start (High Speed) tBUF 500 ns High Speed, VCC = 1.7V to 5.5V 19
Data in hold time (Fast) tHD.DI 0 ns Fast, VCC = 1.7V to 5.5V 19
Data in hold time (High Speed) tHD.DI 0 ns High Speed, VCC = 1.7V to 5.5V 19
Data in setup time (Fast) tSU.DAT 100 ns Fast, VCC = 1.7V to 5.5V 19
Data in setup time (High Speed) tSU.DAT 50 ns High Speed, VCC = 1.7V to 5.5V 19
Data out hold time (Fast) tHD.DAT 50 ns Fast, VCC = 1.7V to 5.5V 19
Data out hold time (High Speed) tHD.DAT 50 ns High Speed, VCC = 1.7V to 5.5V 19
SCL low to data out valid (Fast) tAA 100 900 ns Fast, VCC = 1.7V to 5.5V 19
SCL low to data out valid (High Speed) tAA 50 500 ns High Speed, VCC = 1.7V to 5.5V 19
WP pin setup time (Fast) tSU.WP 1200 ns Fast, VCC = 1.7V to 5.5V 19
WP pin setup time (High Speed) tSU.WP 600 ns High Speed, VCC = 1.7V to 5.5V 19
WP pin hold time (Fast) tHD.WP 1200 ns Fast, VCC = 1.7V to 5.5V 19
WP pin hold time (High Speed) tHD.WP 600 ns High Speed, VCC = 1.7V to 5.5V 19
Write cycle time tWR 5 ms 19
Noise suppression time tI 50 ns 19
Power-On Reset Time tPOR 10 ms 6
Power-On Reset Voltage VPOR 1.5 V 6
Brown-out Reset Voltage VBOR 0.8 V 6
Time from Power-On to First Command tINIT 10 ms 6
Warm Power Cycle Off Time tPOFF 1 ms 6
Input/output capacitance (SDA) CI/O 8 pF VI/O = 0V; TA = +25°C, fC = 1MHz 20
Input capacitance (other pins) CIN 6 pF VIN = 0V; TA = +25°C, fC = 1MHz 20
Data retention DR 200 year TA = +25°C 20
Ambient temperature with power applied TA -40 105 °C 18
Storage temperature TSTG -65 150 °C 18
Supply voltage VCC -0.5 6 V 18
Voltage on input pins VIN -0.5 6 V 18
Electrostatic pulse (human body model) VESD 6000 V 18
Lead temperature (soldering, 10 seconds) TL 260 °C 10 seconds soldering 18
Supply voltage VCC 1.7 5.5 V Operating range TA = -40°C to +105°C 18
Ambient operating temperature range TA -40 105 °C VCC = 1.7V to 5.5V 18

CAD (KiCad official)

  • Symbol: HG24C04CM
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOP-8 (KiCad packages3D, STEP)
  • 3D model files: hg24c04cm-etched.step / hg24c04cm-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); hg24c04cm.step / hg24c04cm.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: HGSEMI datasheet (27 pp, sha256 8bd31d1acd5458af, retrieved 2026-10-28, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF