main
Ray
Publish 0.1.0
639287b
GZP6847D001MPP
Sencoch Semiconductor · Pressure Sensors · DIP-6
GZP6847D001MPP from Sencoch Semiconductor, in a DIP-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL | input | I2C clock line, pulled up to VDD through a typical 4.7 kOhm resistor, with I2C clock frequency up to 400 KHz. |
| 2 | NC | unconnected | No electrical connection may be made to this pin, as doing so may cause product functional failure. |
| 3 | GND | power_in | Ground reference; the product has no reverse-polarity protection, so supply polarity must be observed and a 0.1uF capacitor should be placed between VDD and GND. |
| 4 | VDD | power_in | Supply voltage range 2.5V to 5.5V, with an overvoltage of 6.5Vdc that may burn out the circuit chip. |
| 5 | SDA | bidirectional | I2C serial data line, pulled up to VDD through a typical 4.7 kOhm resistor, which must remain stable while SCL is high except for start and stop conditions. |
| 6 | NC | unconnected | No electrical connection may be made to this pin, as doing so may cause product functional failure. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sencoch Semiconductor |
| Package | DIP-6 |
| Category | Sensors |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 供电电压 (Supply voltage) | 2.5 | 5.5 | V | 5 | |||
| LDO 输出 (LDO output, 3.3V 供电) | 1.62 | 1.8 | 1.98 | V | 3.3V 供电 | 5 | |
| LDO 输出 (LDO output, 5V 供电) | 3.24 | 3.6 | 3.96 | V | 5V 供电 | 5 | |
| 内置温度传感器准确度 (internal temperature sensor accuracy) | -0.5 | 0.5 | ℃ | @25℃ | 5 | ||
| 内置温度传感器准确度 (internal temperature sensor accuracy) | -1 | 1 | ℃ | -40 to 85 ℃ | 5 | ||
| 精度 (accuracy) | -1 | 1 | %Span | 0~70℃ 范围内的输出误差 | 5 | ||
| 零点温度漂移 (zero temperature drift) | -0.03 | 0.03 | %FS/℃ | 5 | |||
| 满程温度漂移 (full-scale temperature drift) | -0.03 | 0.03 | %FS/℃ | 5 | |||
| 过载压力 Rated (overload pressure) | 1.5 | × | 量程>200kPa | 5 | |||
| 破坏压力 (burst pressure) | 2 | × | 量程>200kPa | 5 | |||
| 补偿温度 (compensation temperature) | 0 | 60 | ℃ | 可定制 | 5 | ||
| 工作温度 (operating temperature) | -20 | 100 | ℃ | 5 | |||
| 贮存温度 (storage temperature) | -30 | 150 | ℃ | 5 |
CAD (KiCad official)
- Symbol:
GZP6847D001MPP - Footprint:
Package_DIP:DIP-6_W7.62mm - 3D model: DIP-6 (KiCad packages3D, STEP)
- 3D model files:
gzp6847d001mpp-etched.step/gzp6847d001mpp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);gzp6847d001mpp.step/gzp6847d001mpp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Sencoch Semiconductor datasheet (23 pp, sha256
856f031bb0fd834c, retrieved 2026-11-02, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# GZP6847D001MPP
**Sencoch Semiconductor** · Pressure Sensors · DIP-6
GZP6847D001MPP from Sencoch Semiconductor, in a DIP-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL | input | I2C clock line, pulled up to VDD through a typical 4.7 kOhm resistor, with I2C clock frequency up to 400 KHz. |
| 2 | NC | unconnected | No electrical connection may be made to this pin, as doing so may cause product functional failure. |
| 3 | GND | power_in | Ground reference; the product has no reverse-polarity protection, so supply polarity must be observed and a 0.1uF capacitor should be placed between VDD and GND. |
| 4 | VDD | power_in | Supply voltage range 2.5V to 5.5V, with an overvoltage of 6.5Vdc that may burn out the circuit chip. |
| 5 | SDA | bidirectional | I2C serial data line, pulled up to VDD through a typical 4.7 kOhm resistor, which must remain stable while SCL is high except for start and stop conditions. |
| 6 | NC | unconnected | No electrical connection may be made to this pin, as doing so may cause product functional failure. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sencoch Semiconductor |
| Package | DIP-6 |
| Category | Sensors |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 供电电压 (Supply voltage) | | 2.5 | | 5.5 | V | | 5 |
| LDO 输出 (LDO output, 3.3V 供电) | | 1.62 | 1.8 | 1.98 | V | 3.3V 供电 | 5 |
| LDO 输出 (LDO output, 5V 供电) | | 3.24 | 3.6 | 3.96 | V | 5V 供电 | 5 |
| 内置温度传感器准确度 (internal temperature sensor accuracy) | | -0.5 | | 0.5 | ℃ | @25℃ | 5 |
| 内置温度传感器准确度 (internal temperature sensor accuracy) | | -1 | | 1 | ℃ | -40 to 85 ℃ | 5 |
| 精度 (accuracy) | | -1 | | 1 | %Span | 0~70℃ 范围内的输出误差 | 5 |
| 零点温度漂移 (zero temperature drift) | | -0.03 | | 0.03 | %FS/℃ | | 5 |
| 满程温度漂移 (full-scale temperature drift) | | -0.03 | | 0.03 | %FS/℃ | | 5 |
| 过载压力 Rated (overload pressure) | | | | 1.5 | × | 量程>200kPa | 5 |
| 破坏压力 (burst pressure) | | | | 2 | × | 量程>200kPa | 5 |
| 补偿温度 (compensation temperature) | | 0 | | 60 | ℃ | 可定制 | 5 |
| 工作温度 (operating temperature) | | -20 | | 100 | ℃ | | 5 |
| 贮存温度 (storage temperature) | | -30 | | 150 | ℃ | | 5 |
## CAD (KiCad official)
- Symbol: `GZP6847D001MPP`
- Footprint: `Package_DIP:DIP-6_W7.62mm`
- 3D model: DIP-6 (KiCad packages3D, STEP)
- 3D model files: `gzp6847d001mpp-etched.step` / `gzp6847d001mpp-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `gzp6847d001mpp.step` / `gzp6847d001mpp.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Sencoch Semiconductor datasheet](docs/gzp6847d001mpp-datasheet.pdf) (23 pp, sha256 `856f031bb0fd834c`, retrieved 2026-11-02, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/gzp6847d001mpp-datasheet.pdf)