Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

GZP6847A040KPP50K

Sencoch Semiconductor · Pressure Sensors · DIP-6

GZP6847A040KPP50K from Sencoch Semiconductor, in a DIP-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected Pin 1 is listed as NC with the function 'undefined' (无定义) in the electrical connection table, so it has no specified function and is not defined by the datasheet.
2 VDD power_in Power supply input; the datasheet specifies a supply of (5±0.25) V DC with a typical value referenced to the factory configuration, and an overvoltage of 6.5 Vdc may destroy the circuit chip, so a 0.1 µF capacitor should be placed between VDD and GND.
3 GND power_in Ground connection; the datasheet notes that supply and ground connections need only one of the paired VDD/GND pins to be wired, and the device has no reverse-polarity protection so supply polarity must be observed.
4 VDD power_in Second power supply pin (duplicate of pin 2); the same supply limits apply, with an overvoltage of 6.5 Vdc able to destroy the circuit chip.
5 OUT output Analog ratiometric/standard voltage output; the datasheet gives the output as 0.5-4.5 V (customizable) and a output load current of 5 mA, with the output clamped between GND and VDD limits.
6 GND power_in Second ground pin (duplicate of pin 3); it is connected to the same ground as pin 3 and the same reverse-polarity caution applies.

Key specifications

Parameter Value
Manufacturer Sencoch Semiconductor
Package DIP-6
Category Sensors
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
供电电源 Supply voltage (nominal, tolerance) -0.25 5 0.25 V (5±0.25)V DC supply 4
供电电压 Supply voltage range (product features) 3 5.5 V 3.0~5.5V 供电 (product features) 4
供电电压 Supply voltage (electrical table) 5.5 V 典型值参照出厂配置 5
过载电压 Overload voltage (may burn circuit chip) 6.5 Vdc 6
输出信号 Output signal 0.5 4.5 V 可定制 (customizable) 5
精度 Accuracy (output error) -1 1 %Span 0~70℃ output error (linearity, repeatability, hysteresis) 5
零点温度漂移 Zero-point temperature drift -0.03 0.03 %FS/℃ 5
满量程温度漂移 Full-scale temperature drift -0.03 0.03 %FS/℃ 5
短路电流限制 Short-circuit current limit 15 20 25 mA 5
输入共模信号抑制比 Common-mode rejection ratio 80 110 dB 5
上限钳位电压 Upper clamp voltage 1 VDD 5
下限钳位电压 Lower clamp voltage 0 VDD 5
过载压力 Rated overload pressure 4 × 量程≤60kPa 5
破坏压力 Burst pressure 5 × 量程≤60kPa 5
补偿温度 Compensated temperature range 0 60 ℃ 可定制 (customizable) 5
工作温度 Operating temperature -20 100 ℃ 5
贮存温度 Storage temperature -30 150 ℃ 5
工作电流 Operating current 1700 uA @25℃ 5
PSRR PSRR 60 dB 5
输出电流负载 Output load current 5 mA 5
滤波电容 Filter capacitor 100 nF 5

CAD (KiCad official)

  • Symbol: GZP6847A040KPP50K
  • Footprint: Package_DIP:DIP-6_W7.62mm
  • 3D model: DIP-6 (KiCad packages3D, STEP)
  • 3D model files: gzp6847a040kpp50k-etched.step / gzp6847a040kpp50k-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); gzp6847a040kpp50k.step / gzp6847a040kpp50k.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Sencoch Semiconductor datasheet (13 pp, sha256 6faba1d2ed07c8c4, retrieved 2026-10-31, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF