GM3232ENA

{
 "schema": "adom.pads/1",
 "slug": "gm3232ena",
 "footprint": "SSOP-16_5.3x6.2mm_P0.65mm",
 "generated_from": {
  "footprint": "SSOP-16_5.3x6.2mm_P0.65mm@sha256:9c0306057d45749f",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -3.4125,
   -2.275
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SSOP-16_5.3x6.2mm_P0.65mm@sha256:9c0306057d45749f"
 },
 "pad_count": 16,
 "symbol_pins": [
  "1",
  "10",
  "11",
  "12",
  "13",
  "14",
  "15",
  "16",
  "2",
  "3",
  "4",
  "5",
  "6",
  "7",
  "8",
  "9"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -3.4125,
    -2.275
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "C1+",
   "type": "passive",
   "description": "Positive end of the voltage-doubler charge-pump capacitor C1. Connect an external flying capacitor (0.1µF typical at 3.3V, 0.047µF at 5V) between C1+ (pin 1) and C1- (pin 3).",
   "is_pin1": true,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -3.4125,
    -1.625
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "V+",
   "type": "power_out",
   "description": "Positive voltage produced by the internal charge pump (approximately +2×VCC). Bypass to GND with a reservoir capacitor (0.1µF to 0.47µF depending on VCC). Absolute max +7V; V+ to V- difference must not exceed 13V.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -3.4125,
    -0.975
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "C1-",
   "type": "passive",
   "description": "Negative end of the voltage-doubler charge-pump capacitor C1. Paired with C1+ (pin 1) to form the doubler flying cap.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -3.4125,
    -0.325
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "C2+",
   "type": "passive",
   "description": "Positive end of the inverting charge-pump flying capacitor C2. Connect an external cap (0.1µF to 0.33µF depending on VCC) between C2+ (pin 4) and C2- (pin 5).",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -3.4125,
    0.325
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "C2-",
   "type": "passive",
   "description": "Negative end of the inverting charge-pump flying capacitance. Paired with C2+ (pin 4).",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -3.4125,
    0.975
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "V-",
   "type": "power_out",
   "description": "Negative voltage generated by the internal inverting charge pump (approximately -2×VCC). Bypass to GND with a reservoir capacitor. Absolute max -7V; V+ to V- difference must not exceed 13V.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "7",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -3.4125,
    1.625
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "7",
   "name": "DOUT2",
   "type": "output",
   "description": "RS-232 driver output for channel 2. Swings between V+ and V- to drive an RS-232 line. Short-circuit protected to GND (Ios ±60 mA typ). ESD-protected to ±15 kV HBM / IEC 61000-4-2 air discharge.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "8",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -3.4125,
    2.275
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "8",
   "name": "RIN2",
   "type": "input",
   "description": "RS-232 receiver input for channel 2. Accepts ±25V RS-232 line levels via a built-in 5 kΩ (3-7 kΩ) input resistance to ground. ESD-protected to ±15 kV HBM.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "9",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    3.4125,
    2.275
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "9",
   "name": "ROUT2",
   "type": "output",
   "description": "TTL/CMOS receiver output for channel 2. Drives VCC-referenced logic (VOH ≥ VCC-0.6 at -1 mA, VOL ≤ 0.4 mV at 1.6 mA). Output goes high when RIN2 is open-circuit.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "10",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    3.4125,
    1.625
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "10",
   "name": "DIN2",
   "type": "input",
   "description": "TTL/CMOS driver input for channel 2. VIH ≥ 2.0V (VCC=3.3V) or 2.4V (VCC=5V); VIL ≤ 0.8V. Inverted through the driver to DOUT2.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "11",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    3.4125,
    0.975
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "11",
   "name": "DIN1",
   "type": "input",
   "description": "TTL/CMOS driver input for channel 1. VIH ≥ 2.0V (VCC=3.3V) or 2.4V (VCC=5V); VIL ≤ 0.8V. Inverted through the driver to DOUT1.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "12",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    3.4125,
    0.325
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "12",
   "name": "ROUT1",
   "type": "output",
   "description": "TTL/CMOS receiver output for channel 1. Drives VCC-referenced logic (VOH ≥ VCC-0.6 at -1 mA, VOL ≤ 0.4 mV at 1.6 mA). Output goes high when RIN1 is open-circuit.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "13",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    3.4125,
    -0.325
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "13",
   "name": "RIN1",
   "type": "input",
   "description": "RS-232 receiver input for channel 1. Accepts ±25V RS-232 line levels via a built-in 5 kΩ (3-7 kΩ) input resistance to ground. ESD-protected to ±15 kV HBM.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "14",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    3.4125,
    -0.975
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "14",
   "name": "DOUT1",
   "type": "output",
   "description": "RS-232 driver output for channel 1. Swings between V+ and V- to drive an RS-232 line. Short-circuit protected to GND (Ios ±60 mA typ). ESD-protected to ±15 kV HBM / IEC 61000-4-2 air discharge.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "15",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    3.4125,
    -1.625
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "15",
   "name": "GND",
   "type": "power_in",
   "description": "Device ground reference for logic and analog supply return.",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "16",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    3.4125,
    -2.275
   ],
   "rot": 0.0,
   "size": [
    1.775,
    0.5
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "16",
   "name": "VCC",
   "type": "power_in",
   "description": "+3.0V to +5.5V single-supply input (absolute max +6V). Bypass to GND with a 1µF ceramic capacitor placed close to the pin. Typical supply current ICC = 0.3 mA (no load).",
   "is_pin1": false,
   "source": {
    "geometry": "SSOP-16_5.3x6.2mm_P0.65mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}