component
GC9110
Public Made by Adomby adom
SX globalchip Gate Drivers, ESOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownGC9110
SX globalchip · Gate Drivers · ESOP-8
GC9110 from SX globalchip, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | OUT1 | output | H-bridge output 1, which goes high-impedance (Z) in standby when IN1=IN2=0 and is rated for 1.3 A continuous output current (2.3 A peak). |
| 2 | VCC | power_in | Supply pin for the logic and H-bridge, specified at 2 V to 6 V; the bridge disables below 2 V and re-enables at 2.2 V, and the VCC bypass capacitor should be placed as close to this pin as possible. |
| 3 | VCC | power_in | Second supply pin, connected to the same 2 V to 6 V VCC supply as pin 2. |
| 4 | OUT2 | output | H-bridge output 2, which goes high-impedance (Z) in sleep when IN1=IN2=0 and is rated for 1.3 A continuous output current (2.3 A peak). |
| 5 | GND | power_in | Ground pin, which should be routed separately from the motor return current in the PCB layout. |
| 6 | IN1 | input | Logic input 1 of the PWM IN1/IN2 interface, with a 100 kΩ internal pull-down (defaults low), VIH minimum 2.1 V and VIL maximum 1.0 V at VCC=5 V, and a control input absolute maximum of 7 V. |
| 7 | IN2 | input | Logic input 2 of the PWM IN1/IN2 interface, with a 100 kΩ internal pull-down (defaults low), VIH minimum 2.1 V and VIL maximum 1.0 V at VCC=5 V, and a control input absolute maximum of 7 V. |
| 8 | GND | power_in | Second ground pin, connected to the same ground as pin 5. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SX globalchip |
| Package | ESOP-8 |
| Category | Motor Driver ICs |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Continuous output current (absolute max) | Irms | 1.3 | A | 3 | |||
| Peak output current (absolute max) | Imax | 2.3 | A | 3 | |||
| Supply voltage (absolute max) | VCC | -0.3 | 7 | V | 3 | ||
| Control input voltage range (absolute max) | INx | -0.5 | 7 | V | 3 | ||
| Operating temperature (absolute max) | Top | -40 | 100 | ℃ | 3 | ||
| Junction temperature (absolute max) | Tjmax | -40 | 150 | ℃ | 3 | ||
| Storage temperature (absolute max) | Tstg | -60 | 150 | ℃ | 3 | ||
| ESD protection (human body model) | ESD | -4000 | 4000 | V | Human body model | 3 | |
| Logic supply voltage (recommended) | VCC | 2 | 6 | V | 4 | ||
| Continuous output current (recommended) | IOUT | 0 | 1.3 | A | 4 | ||
| External PWM frequency (recommended) | fPWM | 0 | 250 | kHZ | 4 | ||
| Logic input voltage (recommended) | Vlogic | 0 | 7 | V | 4 | ||
| Operating ambient temperature (recommended) | Ta | -40 | 100 | ℃ | 4 | ||
| VCC operating voltage | VCC | 3 | 5 | 6 | V | 4 | |
| VCC operating current 1 | IVCC | 200 | 550 | uA | VCC=5V, no PWM | 4 | |
| VCC quiescent current (sleep mode) | IVCCQ | 0.01 | 1 | uA | VCC=5V, IN1=IN2=0 power-saving mode | 4 | |
| H-bridge on-resistance (high-side + low-side) | RdsON | 420 | 600 | mΩ | VCC=5V, Io=500mA | 4 | |
| Off-state leakage current | IOFF | -200 | 200 | nA | Vout=0V | 4 | |
| Logic low input voltage (VIL) | VIL | 0 | 0.75 | V | VCC=3V, high-to-low | 4 | |
| Logic low input voltage (VIL) | VIL | 0 | 1 | V | VCC=5V, high-to-low | 4 | |
| Logic high input voltage (VIH) | VIH | 1.3 | V | VCC=3V, low-to-high | 4 | ||
| Logic high input voltage (VIH) | VIH | 2.1 | V | VCC=5V, low-to-high | 4 | ||
| Logic input hysteresis | VHY | 0.4 | V | VCC=3V | 4 | ||
| Logic input hysteresis | VHY | 0.6 | V | VCC=5V | 4 | ||
| Logic low input current | IIL | -5 | 5 | uA | Vin=0 | 4 | |
| Logic high input current | IIH | 50 | uA | Vin=3.3V | 4 | ||
| Input pull-down resistance | Rpd | 100 | kΩ | 4 | |||
| Over-temperature protection threshold | TSD | 150 | 170 | 180 | ℃ | 4 | |
| Over-temperature protection hysteresis | ΔTSD | 30 | ℃ | 4 | |||
| Undervoltage lockout shutdown voltage (falling) | Vuvlo | 2 | V | Voltage decreasing, shutdown voltage | 5 | ||
| Undervoltage lockout hysteresis | ΔUVLO | 200 | mV | Voltage hysteresis | 5 | ||
| Start-up time | T1 | 300 | ns | TA=25°C, VCC=5V, RL=20Ω | 5 | ||
| Turn-off time | T2 | 220 | ns | TA=25°C, VCC=5V, RL=20Ω | 5 | ||
| Input high to output high delay | T3 | 100 | ns | TA=25°C, VCC=5V, RL=20Ω | 5 | ||
| Input low to output low delay | T4 | 100 | ns | TA=25°C, VCC=5V, RL=20Ω | 5 | ||
| Output rising edge time | T5 | 10 | 188 | ns | TA=25°C, VCC=5V, RL=20Ω | 5 | |
| Output falling edge time | T6 | 10 | 188 | ns | TA=25°C, VCC=5V, RL=20Ω | 5 |
CAD (KiCad official)
- Symbol:
GC9110 - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
gc9110-etched.step/gc9110-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);gc9110.step/gc9110.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SX globalchip datasheet (9 pp, sha256
27899edab408adbc, retrieved 2026-10-18, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).