component
GC8418
Public Made by Adomby adom
SX-globalchip Audio Interface ICs, SSOP-28. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownGC8418
SX-globalchip · Audio Interface ICs · SSOP-28
GC8418 from SX-globalchip, in a SSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | AUDIO | output | Channel-status audio bit that reads low for valid linear PCM audio (see non-audio detection); at reset it also selects the serial port format (SFSEL1). |
| 2 | 96KHZ | output | 96 kHz sample-rate detect output that reads 0 for sample rates at or below 48 kHz and 1 at or above 88.1 kHz, with the state undefined in between; at reset it selects the pre-emphasis audio matching function. |
| 3 | RCBL | output | Receiver channel-status block start output that goes high two frames after a Z preamble, stays high for 16 frames, and changes on the RMCK rising edge; at reset it selects serial audio master or slave mode. |
| 4 | U | output | User data output from the AES3 receiver, sampled on both edges of OLRCK; at reset it selects RMCK at 256Fs or 128Fs. |
| 5 | C | output | Channel-status data output from the AES3 receiver, sampled on both edges of OLRCK; at reset it selects the serial port format (SFSEL0). |
| 6 | TX | output | Multiplexed S/PDIF output channel; at reset it also selects the phase detector type (PDUR), and if the TX path is unused the receiver input must be set so that TX is not used. |
| 7 | VD | power_in | Digital power supply, normally +3.3 V or +5.0 V per the pin table, while the recommended VD range in Section 2 is 3.13 V to 3.6 V. |
| 8 | RMCK | output | Recovered master clock output at 256×Fs by default, switched to 128×Fs via the RMCKF bit in register 01h, and placed in high impedance via the RXD bit in register 04h. |
| 9 | SDOUT | output | Serial audio data output that must have a 47 kΩ pull-down resistor to GND. |
| 10 | MCLK | input | DAC master clock input; RMCK/MCLK maximum frequency is 50 MHz. |
| 11 | VQ | passive | Internal DAC DC bias voltage at 0.5·VAA VDC, with a maximum VQ current of 100 µA. |
| 12 | GND | power_in | DAC analog ground. |
| 13 | AOUTL | output | Analog left-channel output with 0.65·VAA Vpp full-scale swing, maximum DC current 10 µA, maximum AC load 3 kΩ and maximum load capacitance 100 pF. |
| 14 | FILT+ | passive | DAC positive reference voltage pin. |
| 15 | VCC | power_in | DAC power supply pin. |
| 16 | AOUTR | output | Analog right-channel output with 0.65·VAA Vpp full-scale swing, maximum DC current 10 µA, maximum AC load 3 kΩ and maximum load capacitance 100 pF. |
| 17 | RXP3 | input | AES3/SPDIF positive input, single-ended or differential, selected through RXSEL[1:0]; AC-couple through 0.01 µF to 0.1 µF and leave unused inputs floating or tied to AGND. |
| 18 | RXP2 | input | AES3/SPDIF positive input, single-ended or differential, selected through RXSEL[1:0]; AC-couple through 0.01 µF to 0.1 µF and leave unused inputs floating or tied to AGND. |
| 19 | RXP1 | input | AES3/SPDIF positive input, single-ended or differential, selected through RXSEL[1:0]; AC-couple through 0.01 µF to 0.1 µF and leave unused inputs floating or tied to AGND. |
| 20 | RXP0 | input | AES3/SPDIF positive input, single-ended or differential, selected through RXSEL[1:0]; AC-couple through 0.01 µF to 0.1 µF and leave unused inputs floating or tied to AGND. |
| 21 | RXN | input | AES3/SPDIF negative input shared by RXP[3:0]; for single-ended operation it is AC-coupled to ground through a capacitor. |
| 22 | VA | power_in | Analog power supply, nominally +3.3 V; noise on this supply causes jitter in the recovered clock. |
| 23 | AGND | power_in | Analog ground. |
| 24 | FILT | passive | PLL filter output that requires an RC filter network between this pin and analog ground. |
| 25 | RST | input | Reset input; holding it low enters low-power mode and resets internal state, and it must stay low at power-up until supplies and input clocks are stable in frequency and phase. |
| 26 | RXSEL1 | input | Receiver input multiplexer select bit 1, choosing one of RXP[3:0] as the receiver input. |
| 27 | RXSEL0 | input | Receiver input multiplexer select bit 0, choosing one of RXP[3:0] as the receiver input. |
| 28 | NV/RERR | output | Error flag output; a 47 kΩ resistor to GND selects NVERR and a 47 kΩ resistor to VD selects RERR, with the mode latched at power-up. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | SX-globalchip |
| Package | SSOP-28 |
| Category | Interface |
| Pins | 28 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage (on digital pins) | Vin | -0.3 | V | 5 | |||
| Input current, pins other than supply | Iin | -10 | 10 | mA | Pins other than supply (Note 1) | 5 | |
| Operating temperature (absolute maximum) | TA | -55 | 125 | ℃ | 5 | ||
| Storage temperature | Tstg | -65 | 150 | ℃ | 5 | ||
| Supply voltage VA, VD, VGC | VA,VD,VGC | 6 | V | 5 | |||
| Supply voltage VA | VA | 3.13 | 3.3 | 5.25 | V | AGND, DGND = 0 V | 5 |
| Supply voltage VD | VD | 3.13 | 3.3 | 3.6 | V | AGND, DGND = 0 V | 5 |
| Supply voltage VGC | VGC | 3.13 | 3.3 | 5.25 | V | AGND, DGND = 0 V | 5 |
| Operating temperature, commercial grade | TA | -10 | 70 | ℃ | Commercial grade | 5 | |
| Input leakage current | IIN | -0.5 | 0.5 | μA | AGND = DGND = 0 V | 6 | |
| Differential input sensitivity, RXP[7:0] to RXN | VTH | 150 | 200 | mVpp | RXP[7:0] to RXN | 6 | |
| Input hysteresis | VH | 0.15 | 1 | V | 6 | ||
| RST low pulse width | 200 | μs | Logic low input 0 V, logic high VL; CL = 20 pF | 6 | |||
| PLL clock recovery sample rate range | 30 | 200 | kHz | Logic low input 0 V, logic high VL; CL = 20 pF | 6 | ||
| RMCK duty cycle | 45 | 50 | 55 | % | Clock recovered from biphase-coded input (Note 6) | 6 | |
| RMCK duty cycle | 50 | 55 | 65 | % | MCLK used as RMCK output (Note 7) | 6 | |
| RMCK/MCLK maximum frequency | 50 | MHz | 6 | ||||
| Maximum DAC output DC current at AOUT | IOUTmax | 10 | uA | TA = 25°C, full-scale sine 997 Hz, Fs = 48/96/192 kHz; RL = 3 kΩ, CL = 10 pF | 7 | ||
| Maximum VQ pin current | IQmax | 100 | uA | TA = 25°C, full-scale sine 997 Hz, Fs = 48/96/192 kHz; RL = 3 kΩ, CL = 10 pF | 7 | ||
| Maximum AC load resistance | RL | 3 | kΩ | Figure 20 | 7 | ||
| Maximum load capacitance | CL | 100 | pF | Figure 20 | 7 |
CAD (KiCad official)
- Symbol:
GC8418 - Footprint:
Package_SO:SSOP-28_5.3x10.2mm_P0.65mm - 3D model: SSOP-28 (KiCad packages3D, STEP)
- 3D model files:
gc8418-etched.step/gc8418-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);gc8418.step/gc8418.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: SX-globalchip datasheet (11 pp, sha256
399de7df769f4f41, retrieved 2026-11-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).