component
GC7129BF
Public Made by Adomby adom
Sungine Analog To Digital Converters (ADC), LQFP-44(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownGC7129BF
Sungine · Analog To Digital Converters (ADC) · LQFP-44(10x10)
GC7129BF from Sungine, in a LQFP-44(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DGND | power_in | Internal digital-section reference ground, measured at 4.5-5.8 V (typ 5.3 V) below V+ with V+ to V- = 9 V, with a leakage limit of 1.2 mA at DGND = +0.5 V. |
| 2 | RANGE | input | Full-scale range select: 200 mV full scale when low (internal pull-down about 3 µA), 2 V full scale when high. |
| 3 | DP2 | input | Decimal point driver input; when high, it lights the first decimal point as printed in the datasheet. |
| 4 | DP1 | input | Decimal point driver input; when high, it lights the first decimal point. |
| 5 | OSC2 | passive | Output of the first-stage clock converter and input of the second-stage clock converter; clock frequency 120 kHz typ, 360 kHz max. |
| 6 | OSC1 | input | Input of the first-stage clock converter; clock frequency 120 kHz typ, 360 kHz max. |
| 7 | OSC3 | output | Output of the second-stage clock converter. |
| 8 | NC | unconnected | Empty pin, no internal connection. |
| 9 | NC | unconnected | Empty pin, no internal connection. |
| 10 | ANNUNCE DRIVE | output | Backplane square-wave output used to drive a buzzer. |
| 11 | B1,C1,CONT | output | Display segment output (segments B1, C1 and CONT as printed). |
| 12 | A1,G1,D1 | output | Display segment output (segments A1, G1 and D1). |
| 13 | F1,E1,DP1 | output | Display segment output (segments F1, E1 and DP1). |
| 14 | B2,C2,LO,BAT | output | Display segment output (segments B2, C2 and the LO and BAT annunciators as printed). |
| 15 | A2,G2,D2 | output | Display segment output (segments A2, G2 and D2). |
| 16 | F2,E2,DP2 | output | Display segment output (segments F2, E2 and DP2). |
| 17 | B3,C3,MINUS | output | Display segment output (segments B3, C3 and the MINUS sign). |
| 18 | A3,G3,D3 | output | Display segment output (segments A3, G3 and D3). |
| 19 | F3,E3,DP3 | output | Display segment output (segments F3, E3 and DP3). |
| 20 | B4,C4,BC5 | output | Display segment output (segments B4, C4 and BC5 as printed). |
| 21 | A4,D4,G4 | output | Display segment output (segments A4, D4 and G4). |
| 22 | F4,E4,DP4 | output | Display segment output (segments F4, E4 and DP4). |
| 23 | BP3 | output | Display backplane driver 3 output. |
| 24 | BP2 | output | Display backplane driver 2 output. |
| 25 | BP1 | output | Display backplane driver 1 output. |
| 26 | VDISP | power_in | Negative supply input for display drive; resistance from VDISP to V+ is 50 kΩ typ. |
| 27 | DP4/OR | bidirectional | Input: when high, lights the most significant decimal point. Output: goes high when the count exceeds ±19,999 (overrange). |
| 28 | DP3/UR | bidirectional | Input: when high, lights the second decimal point. Output: goes high when the count is below ±1000 (underrange). |
| 29 | LATCH/HOLD | bidirectional | Input: when floating, the ADC runs in free-run mode; when high, the last reading is held; when low, the result counter contents are acted on (sentence truncated in source). Output: goes low when the data latch updates and can serve as a converter status signal. |
| 30 | NC | unconnected | Empty pin, no internal connection. |
| 31 | NC | unconnected | Empty pin, no internal connection. |
| 32 | V- | power_in | Negative power supply connection; supply V+ to V- is 6-12 V (9 V typ), absolute maximum 15 V. |
| 33 | V+ | power_in | Positive power supply connection; supply V+ to V- is 6-12 V (9 V typ), absolute maximum 15 V. |
| 34 | INT IN | input | Integrator input. |
| 35 | INT OUT | output | Integrator output. |
| 36 | CONTINUITY | bidirectional | Input: when low, the continuity indicator is not shown; when high, it is shown. Output: goes high when the input is below +200 mV (output sentence truncated in source). |
| 37 | COMMON | passive | Sets the common-mode voltage; V+ to this pin is 2.8-3.5 V (3.2 V typ). |
| 38 | CREF+ | passive | Positive terminal of the external reference capacitor. |
| 39 | CREF- | passive | Negative terminal of the external reference capacitor. |
| 40 | BUFF | output | Output of the buffer amplifier. |
| 41 | IN LO | input | Negative differential input terminal; common-mode range is (V-)+1.5 V to (V+)-1 V. |
| 42 | IN HI | input | Positive differential input terminal; input may exceed the supply but input current must be limited to ±400 µA. |
| 43 | REF HI | input | Positive reference voltage input; reference must lie within the V+ to V- range. |
| 44 | REF LO | input | Negative reference voltage input; reference must lie within the V+ to V- range. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Sungine |
| Package | LQFP-44(10x10) |
| Category | Data Acquisition |
| Pins | 44 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 工作温度 (operating temperature, -40 to +105) | -40 | 105 | ℃ | 8 | |||
| 电源电压 (supply voltage V+ to V-) | 15 | V | 8 | ||||
| 贮存温度 (storage temperature) | -65 | 150 | ℃ | 8 | |||
| 工作温度 (operating temperature, 0 to +70) | 0 | 70 | ℃ | 8 | |||
| 最大结温 (maximum junction temperature) | 150 | ℃ | 8 | ||||
| 输入电流 (input current limit, note 1) | -400 | 400 | µA | Note 1: input voltage may exceed supply; input current must be limited to ±400µA | 8 | ||
| 零输入读数 | 0 | 0 | 0 | 读数 | VIN=0V~200mV | 9 | |
| 零读数温漂 | -0.5 | 0.5 | µV/℃ | VIN=0V, 0℃<TA<+70℃ | 9 | ||
| 最大量程 | 9997 | 9999 | 10000 | 读数 | VIN=VREF=1000mV, Range=2V | 9 | |
| 精确度 | 0.9999 | 1 | 1.0001 | 比例 | 9 | ||
| 翻转误差 RE | RE | 1 | 2 | 读数 | VIN-=VIN+=199mV | 9 | |
| 输入漏电流 IIN | IIN | 1 | 10 | pA | VIN=0V | 9 | |
| 量程标度因子温度系数 | 2 | 7 | ppm/℃ | VIN=199mV, 0℃<TA<+70℃, VREF=0ppm/℃ | 9 | ||
| 公共电压 VCOM | VCOM | 2.8 | 3.2 | 3.5 | V | V+到 28 脚 | 9 |
| 数字地电压 DGND | DGND | 4.5 | 5.3 | 5.8 | V | V+到 36 脚, V+到 V-=9V | 9 |
| 电源电压范围 | 6 | 9 | 12 | V | 9 | ||
| 电源电流(除公共电流外)IS | IS | 0.8 | 1.3 | mA | V+到 V-=9V | 9 | |
| 时钟频率 tCLK | tCLK | 120 | 360 | kHz | 9 | ||
| 欠电压标志激活电压 | 6.3 | 7.2 | 7.7 | V | V+到 V- | 10 | |
| 连续比较器极限电压 (row 1) | VOUT | 100 | 200 | mV | 10 | ||
| 连续比较器极限电压 (row 2) | VOUT | 200 | 400 | mV | 10 | ||
| 下拉电流 | 2 | 10 | µA | 10 |
CAD (KiCad official)
- Symbol:
GC7129BF - Footprint:
Package_QFP:LQFP-44_10x10mm_P0.8mm - 3D model: LQFP-44(10x10) (KiCad packages3D, STEP)
- 3D model files:
gc7129bf-etched.step/gc7129bf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);gc7129bf.step/gc7129bf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Sungine datasheet (12 pp, sha256
ef542b7692799dc8, retrieved 2026-11-10, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).