component
FT8215Q
Public Made by Adomby adom
Fortior Tech Motor Driver ICs, QFN-24(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownFT8215Q
Fortior Tech · Motor Driver ICs · QFN-24(4x4)
FT8215Q from Fortior Tech, in a QFN-24(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CP1 | output | Charge-pump pin; a 0.1 μF capacitor is connected between CP2 and CP1. |
| 2 | VDD5 | power_out | 5 V LDO output that needs a 1 μF to 4.7 μF capacitor to ground; operating range 4.8-5.2 V at 0-10 mA load. |
| 3 | GND | power_in | Ground. |
| 4 | VREF | power_in | ADC reference voltage (4.3-4.7 V, 4.5 V typ) that needs a 1 μF or larger capacitor to ground and must not be used to power external circuits. |
| 5 | DIR | input | Motor direction control with internal pull-up (default high): 0 gives reverse with output phase sequence U→W→V, and 1 gives forward with output phase sequence U→V→W. |
| 6 | SMP | input | Bus current sampling input used in single-resistor mode. |
| 7 | ASPEED | input | Analog voltage speed-control input, valid over 0 to VREF V when analog speed control is selected. |
| 8 | SPEED/SCL | bidirectional | Speed input for PWM (20 Hz-100 kHz) or CLOCK (20-1400 Hz) control, with VIH of 2.5 V min and VIL of 0.6 V max, and it serves as I2C SCL when I2C speed control is selected. |
| 9 | FG/SDA | bidirectional | Open-collector speed-feedback or fault (RD) output, and it serves as I2C SDA when I2C speed control is selected. |
| 10 | VCC | power_in | Input supply pin. |
| 11 | W | output | W-phase motor output. |
| 12 | W | output | W-phase motor output. |
| 13 | VSL | output | Low-side bridge ground terminal that must not exceed 0.5 V relative to VSS; in single-resistor mode it connects to the sense resistor, and in dual/triple-resistor mode it is tied directly to ground. |
| 14 | VSL | output | Low-side bridge ground terminal that must not exceed 0.5 V relative to VSS; in single-resistor mode it connects to the sense resistor, and in dual/triple-resistor mode it is tied directly to ground. |
| 15 | V | power_in | V-phase motor output. |
| 16 | V | power_in | V-phase motor output. |
| 17 | VSL | output | Low-side bridge ground terminal that must not exceed 0.5 V relative to VSS; in single-resistor mode it connects to the sense resistor, and in dual/triple-resistor mode it is tied directly to ground. |
| 18 | VSL | output | Low-side bridge ground terminal that must not exceed 0.5 V relative to VSS; in single-resistor mode it connects to the sense resistor, and in dual/triple-resistor mode it is tied directly to ground. |
| 19 | U | output | U-phase motor output. |
| 20 | U | output | U-phase motor output. |
| 21 | VCC | power_in | Input supply, 5 V to 18 V DC, with a capacitor of at least 1 μF to ground. |
| 22 | VCC | power_in | Input supply pin. |
| 23 | VCP | power_out | Charge-pump output that needs a 1 μF to 4.7 μF capacitor to VCC. |
| 24 | CP2 | output | Charge-pump pin; a 0.1 μF capacitor is connected between CP2 and CP1. |
| 25 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Fortior Tech |
| Package | QFN-24(4x4) |
| Category | Power Supply Chip |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating junction temperature | Tj | -40 | 150 | ℃ | 12 | ||
| Storage temperature | Tstg | -55 | 150 | ℃ | 12 | ||
| VCC voltage relative to VSS | VCC | -0.3 | 22 | V | 12 | ||
| VDD5 voltage relative to VSS | VDD5 | -0.3 | 5 | 6.5 | V | 12 | |
| FG, U, V, W, CP1 voltage relative to VSS (printed max VCC + 0.3 V) | FG,U,V,W,CP1 | -0.3 | V | 12 | |||
| VSL voltage relative to VSS | VSL | -0.3 | 0.5 | V | 12 | ||
| VCP, CP2 voltage relative to VSS (printed max VCC + 6.0 V) | VCP,CP2 | -0.3 | V | 12 | |||
| VREF/DIR/SMP/ASPEED/SPEED voltage relative to VSS (printed max VDD5 + 0.3 V) | VREF,DIR,SMP,ASPEED,SPEED | -0.3 | V | 12 | |||
| VCC operating voltage | VCC | 5 | 18 | V | 12 | ||
| VDD5 operating voltage | VDD5 | 4.8 | 5 | 5.2 | V | I = 0 ~ 10mA | 12 |
| VREF reference voltage | VREF | 4.3 | 4.5 | 4.7 | V | 12 | |
| VCC operating current, average | IVCC | 2 | A | TA = 25℃ 平均值 | 12 | ||
| VCC operating current, average | IVCC | 1.8 | A | TA = 85℃ 平均值 | 12 | ||
| On-resistance, high-side MOS + low-side MOS | Rdson | 0.22 | 0.4 | Ω | 12 | ||
| VCC undervoltage protection threshold | VUVLO | 3.2 | 3.5 | 3.8 | V | 12 | |
| Overcurrent protection threshold | Iocp | 3.5 | 4 | 4.5 | A | 13 | |
| Thermal shutdown hysteresis | TTSD_HYS | 15 | 20 | ℃ | 13 | ||
| Input high voltage (printed max VDD5) | VIH | 2.5 | V | 13 | |||
| Input low voltage | VIL | 0 | 0.6 | V | 13 | ||
| PWM speed input frequency range, minimum | 20 | Hz | 13 | ||||
| PWM speed input frequency range, maximum | 100 | kHz | 13 | ||||
| CLOCK speed input frequency range | 20 | 1400 | Hz | 13 | |||
| ASPEED analog speed input voltage range (printed max VREF) | ASPEED | 0 | V | 13 | |||
| Thermal resistance, junction to ambient | θJA | 50 | ℃/W | JEDEC standard, 2S2P PCB | 13 | ||
| Thermal resistance, junction to package surface | θJA | 25 | ℃/W | JEDEC standard, 2S2P PCB | 13 |
CAD (KiCad official)
- Symbol:
FT8215Q - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: QFN-24(4x4) (KiCad packages3D, STEP)
- 3D model files:
ft8215q-etched.step/ft8215q-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft8215q.step/ft8215q.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Fortior Tech datasheet (20 pp, sha256
b3819660764ec3a4, retrieved 2026-11-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).