component
FT4232HPQ-TRAY
Public Made by Adomby adom
FTDI USB ICs, QFN-68(8x8). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
56c0310
FT4232HPQ-TRAY
FTDI · USB ICs · QFN-68(8x8)
FT4232HPQ-TRAY from FTDI, in a QFN-68(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EECLK | output | Clock signal to the EEPROM; tri-state during device reset, and outputs the EEPROM clock when not in reset. |
| 2 | EEDATA | bidirectional | EEPROM data I/O; connect directly to EEPROM Data-In and to Data-Out via a 2.2K resistor, pull Data-Out to VCC via 10K, tri-state during device reset. |
| 3 | TEST | input | IC test pin that should be connected to GND for normal operation. |
| 4 | RESET# | input | Active-low reset input; tie to VCCIO (+3.3V) if not used. |
| 5 | GPIO3 | bidirectional | GPIO3 pin whose default function is an input with weak pull-down. |
| 6 | ADBUS0 | bidirectional | Channel A bit 0: TXD in UART mode, D0 in bit-bang mode, TCK/SK in MPSSE mode. |
| 7 | ADBUS1 | bidirectional | Channel A bit 1: RXD in UART mode, D1 in bit-bang mode, TDI/DO in MPSSE mode. |
| 8 | VCORE | power_in | +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator. |
| 9 | GND | power_in | Ground. |
| 10 | VCCIO | power_in | +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail. |
| 11 | ADBUS2 | bidirectional | Channel A bit 2: RTS# in UART mode, D2 in bit-bang mode, TDO/DI in MPSSE mode. |
| 12 | ADBUS3 | bidirectional | Channel A bit 3: CTS# in UART mode, D3 in bit-bang mode, TMS/CS in MPSSE mode. |
| 13 | ADBUS4 | bidirectional | Channel A bit 4: DTR# in UART mode, D4 in bit-bang mode, GPIOL0 in MPSSE mode. |
| 14 | ADBUS5 | bidirectional | Channel A bit 5: DSR# in UART mode, D5 in bit-bang mode, GPIOL1 in MPSSE mode. |
| 15 | ADBUS6 | bidirectional | Channel A bit 6: DCD# in UART mode, D6 in bit-bang mode, GPIOL2 in MPSSE mode. |
| 16 | ADBUS7 | bidirectional | Channel A bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, D7 in bit-bang mode, GPIOL3 in MPSSE mode. |
| 17 | BDBUS0 | bidirectional | Channel B bit 0: TXD in UART mode, D0 in bit-bang mode, TCK/SK in MPSSE mode. |
| 18 | BDBUS1 | bidirectional | Channel B bit 1: RXD in UART mode, D1 in bit-bang mode, TDI/DO in MPSSE mode. |
| 19 | BDBUS2 | bidirectional | Channel B bit 2: RTS# in UART mode, D2 in bit-bang mode, TDO/DI in MPSSE mode. |
| 20 | BDBUS3 | bidirectional | Channel B bit 3: CTS# in UART mode, D3 in bit-bang mode, TMS/CS in MPSSE mode. |
| 21 | BDBUS4 | bidirectional | Channel B bit 4: DTR# in UART mode, D4 in bit-bang mode, GPIOL0 in MPSSE mode. |
| 22 | BDBUS5 | bidirectional | Channel B bit 5: DSR# in UART mode, D5 in bit-bang mode, GPIOL1 in MPSSE mode. |
| 23 | BDBUS6 | bidirectional | Channel B bit 6: DCD# in UART mode, D6 in bit-bang mode, GPIOL2 in MPSSE mode. |
| 24 | BDBUS7 | bidirectional | Channel B bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, D7 in bit-bang mode, GPIOL3 in MPSSE mode. |
| 25 | VCORE | power_in | +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator. |
| 26 | VCCIO | power_in | +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail. |
| 27 | OSCI | input | Oscillator input; a 12 MHz crystal is connected to OSCI and OSCO. |
| 28 | OSCO | output | Oscillator output; a 12 MHz crystal is connected to OSCI and OSCO. |
| 29 | GND | power_in | Ground. |
| 30 | VREGIN | power_in | +3.3V input to the integrated 1.2V voltage regulator. |
| 31 | VREGOUT | power_out | +1.2V integrated regulator output; connect to VCORE with a 3.3uF filter capacitor and do not use to power other circuits. |
| 32 | FSOURCE | power_in | FSOURCE input pin for EFUSE; leave floating for normal operation. |
| 33 | VPP | power_in | VPP input pin for EFUSE; leave floating for normal operation. |
| 34 | CDBUS0 | bidirectional | Channel C bit 0: TXD in UART mode or D0 in bit-bang mode. |
| 35 | CDBUS1 | bidirectional | Channel C bit 1: RXD in UART mode or D1 in bit-bang mode. |
| 36 | CDBUS2 | bidirectional | Channel C bit 2: RTS# in UART mode or D2 in bit-bang mode. |
| 37 | CDBUS3 | bidirectional | Channel C bit 3: CTS# in UART mode or D3 in bit-bang mode. |
| 38 | CDBUS4 | bidirectional | Channel C bit 4: DTR# in UART mode or D4 in bit-bang mode. |
| 39 | VCCIO | power_in | +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail. |
| 40 | CDBUS5 | bidirectional | Channel C bit 5: DSR# in UART mode or D5 in bit-bang mode. |
| 41 | CDBUS6 | bidirectional | Channel C bit 6: DCD# in UART mode or D6 in bit-bang mode. |
| 42 | CDBUS7 | bidirectional | Channel C bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, or D7 in bit-bang mode. |
| 43 | SUSPEND# | output | Active-low output that is low when USB is in suspend mode. |
| 44 | VCORE | power_in | +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator. |
| 45 | DDBUS0 | bidirectional | Channel D bit 0: TXD in UART mode or D0 in bit-bang mode. |
| 46 | DDBUS1 | bidirectional | Channel D bit 1: RXD in UART mode or D1 in bit-bang mode. |
| 47 | DDBUS2 | bidirectional | Channel D bit 2: RTS# in UART mode or D2 in bit-bang mode. |
| 48 | DDBUS3 | bidirectional | Channel D bit 3: CTS# in UART mode or D3 in bit-bang mode. |
| 49 | DDBUS4 | bidirectional | Channel D bit 4: DTR# in UART mode or D4 in bit-bang mode. |
| 50 | DDBUS5 | bidirectional | Channel D bit 5: DSR# in UART mode or D5 in bit-bang mode. |
| 51 | VCCIO | power_in | +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail. |
| 52 | DDBUS6 | bidirectional | Channel D bit 6: DCD# in UART mode or D6 in bit-bang mode. |
| 53 | DDBUS7 | bidirectional | Channel D bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, or D7 in bit-bang mode. |
| 54 | GPIO2 | bidirectional | GPIO2 or I2C_INT# pin whose default function is GPIO2 input with weak pull-down. |
| 55 | GPIO1 | bidirectional | GPIO1 or I2C_SCL pin whose default function is GPIO1 input with weak pull-down. |
| 56 | GPIO0 | bidirectional | GPIO0 or I2C_SDA pin whose default function is GPIO0 input with weak pull-down. |
| 57 | VCC_USB | power_in | +3.3V internal USB PHY supply input that cannot be connected directly to the USB supply; a +3.3V regulator is required and LC filtering is recommended. |
| 58 | DM | bidirectional | USB data signal minus. |
| 59 | DP | bidirectional | USB data signal plus. |
| 60 | REF | input | Current reference input; connect via a 12K Ohm 1% resistor to GND. |
| 61 | VCC_PD | power_in | +3.3V internal PD PHY power supply input. |
| 62 | PD1_CC2 | bidirectional | Analog I/O pin for the PD1 CC2 line. |
| 63 | PD1_SVBUS | input | Analog input for scaled-down PD1 VBUS sensing; VBUS must be divided by 10 before this pin. |
| 64 | PD1_VCONN | power_in | Power input for the PD1 VCONN power source; connect to 3.3V. |
| 65 | PD1_CC1 | bidirectional | Analog I/O pin for the PD1 CC1 line. |
| 66 | VCORE | power_in | +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator. |
| 67 | PWREN# | output | Active-low power-enable output: 0 = normal operation, 1 = USB suspend or device not configured. |
| 68 | EECS | bidirectional | EEPROM chip select, tri-state during device reset; pull to VCCIO via 10K if no EEPROM. |
| 69 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FTDI |
| Package | QFN-68(8x8) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 69 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | -65 | 150 | °C | 27 | |||
| Ambient Operating Temperature (Power Applied) | -40 | 85 | °C | Power Applied | 27 | ||
| VCORE Supply Voltage | VCORE | -0.3 | 2 | V | 27 | ||
| VCCIO IO Voltage | VCCIO | -0.3 | 4 | V | 27 | ||
| DC Input Voltage, USBDP and USBDM | -0.5 | 3.63 | V | 27 | |||
| DC Input Voltage, High Impedance Bi-directional (powered from VCCIO) | -0.3 | 5.8 | V | powered from VCCIO | 27 | ||
| DC Input Voltage, All Other Inputs | -0.5 | V | max is + (VCCIO +0.5) | 27 | |||
| DC Output Current, Outputs | 16 | mA | 27 | ||||
| VCORE VCC Core Operating Supply Voltage | VCORE | 1.08 | 1.2 | 1.32 | V | 27 | |
| VCCIO Operating Supply Voltage | VCCIO | 2.97 | 3.3 | 3.63 | V | 27 | |
| VREGIN Voltage regulator Input | VREGIN | 3 | 3.3 | 3.6 | V | 27 | |
| VREGOUT Voltage regulator Output | VREGOUT | 1.08 | 1.2 | 1.32 | V | 27 | |
| Regulator Current | Ireg | 21.11 | 150 | mA | VREGIN +3.3V and data transfer with 12Mbps | 27 | |
| VREGIN Suspend Supply Current | Icc1s | 1.64 | mA | USB Suspend | 27 | ||
| VCC_USB operating supply current | I_vcd_usb | 22.7 | mA | Data transfer with 12Mbps | 27 | ||
| VCC_IO operating supply current | I_vccio | 0.87 | mA | Data transfer with 12Mbps | 27 | ||
| VCC_PD suspend supply current | I_vcc_pd | 209 | uA | PD suspend | 27 | ||
| Output Voltage High | Voh | 2.4 | 3.14 | V | Ioh = +/-2mA | 28 | |
| Output Voltage High | Voh | 3.2 | V | I/O Drive strength* = 8mA | 28 | ||
| Output Voltage High | Voh | 3.22 | V | I/O Drive strength* = 12mA | 28 | ||
| Output Voltage Low | Vol | 0.18 | 0.4 | V | Iol = +/-2mA | 28 | |
| Output Voltage Low | Vol | 0.12 | V | I/O Drive strength* = 8mA | 28 | ||
| Output Voltage Low | Vol | 0.08 | V | I/O Drive strength* = 12mA | 28 | ||
| Output Voltage Low | Vol | 0.07 | V | I/O Drive strength* = 16mA | 28 | ||
| Input low Switching Threshold | Vil | 0.8 | V | LVTTL | 28 | ||
| Input High Switching Threshold | Vih | 2 | V | LVTTL | 28 | ||
| Schmitt trigger negative going threshold voltage | Vt- | 0.8 | 1.1 | V | 28 | ||
| Schmitt trigger positive going threshold voltage | Vt+ | 1.6 | 2 | V | 28 | ||
| Input pull-up resistance | Rpu | 40 | 75 | 190 | KΩ | Vin = 0 | 28 |
| Input pull-down resistance | Rpd | 40 | 75 | 190 | KΩ | Vin =VCCIO | 28 |
| Input Leakage Current | Iin | 15 | 45 | 85 | μA | Vin = 0 | 28 |
| Tri-state output leakage current | Ioz | -10 | 10 | μA | Vin = 5.5V or 0 | 28 | |
| Human Body Model (HBM) | -2 | 2 | kV | ANSI/ESDA/JEDEC JS-001 Class 2 | 28 | ||
| Machine Mode (MM) | -200 | 200 | V | JEDEC EIA/JESD22-A115-C, Class B | 28 | ||
| Charge Device Model (CDM) | -500 | 500 | V | ANSI/ESDA/JEDEC JS-002, JEDEC JESD22-C101-D Class-III | 28 | ||
| Latch-up | -200 | 200 | mA | JEDEC STANDARD EIA/JESD78, Trigger Class-II | 28 | ||
| TJ Junction Temperature (FT4232HPQ) | TJ | -40 | 25 | 125 | °C | FT4233HPL/FT4233HPQ/FT4232HPQ | 29 |
| ѲJA Thermal Resistance Junction-to-Ambient (FT4232HPQ) | ѲJA | 23.65 | °C/W | Preliminary data | 29 | ||
| ѲJC Thermal Resistance Junction-to-Case (FT4232HPQ) | ѲJC | 9.35 | °C/W | Preliminary data | 29 |
CAD (KiCad official)
- Symbol:
FT4232HPQ-TRAY - Footprint:
Package_DFN_QFN:QFN-68-1EP_8x8mm_P0.4mm_EP5.2x5.2mm - 3D model: QFN-68(8x8) (KiCad packages3D, STEP)
- 3D model files:
ft4232hpq-tray-etched.step/ft4232hpq-tray-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft4232hpq-tray.step/ft4232hpq-tray.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FTDI datasheet (39 pp, sha256
4394e4c473a80dcf, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# FT4232HPQ-TRAY
**FTDI** · USB ICs · QFN-68(8x8)
FT4232HPQ-TRAY from FTDI, in a QFN-68(8x8). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EECLK | output | Clock signal to the EEPROM; tri-state during device reset, and outputs the EEPROM clock when not in reset. |
| 2 | EEDATA | bidirectional | EEPROM data I/O; connect directly to EEPROM Data-In and to Data-Out via a 2.2K resistor, pull Data-Out to VCC via 10K, tri-state during device reset. |
| 3 | TEST | input | IC test pin that should be connected to GND for normal operation. |
| 4 | RESET# | input | Active-low reset input; tie to VCCIO (+3.3V) if not used. |
| 5 | GPIO3 | bidirectional | GPIO3 pin whose default function is an input with weak pull-down. |
| 6 | ADBUS0 | bidirectional | Channel A bit 0: TXD in UART mode, D0 in bit-bang mode, TCK/SK in MPSSE mode. |
| 7 | ADBUS1 | bidirectional | Channel A bit 1: RXD in UART mode, D1 in bit-bang mode, TDI/DO in MPSSE mode. |
| 8 | VCORE | power_in | +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator. |
| 9 | GND | power_in | Ground. |
| 10 | VCCIO | power_in | +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail. |
| 11 | ADBUS2 | bidirectional | Channel A bit 2: RTS# in UART mode, D2 in bit-bang mode, TDO/DI in MPSSE mode. |
| 12 | ADBUS3 | bidirectional | Channel A bit 3: CTS# in UART mode, D3 in bit-bang mode, TMS/CS in MPSSE mode. |
| 13 | ADBUS4 | bidirectional | Channel A bit 4: DTR# in UART mode, D4 in bit-bang mode, GPIOL0 in MPSSE mode. |
| 14 | ADBUS5 | bidirectional | Channel A bit 5: DSR# in UART mode, D5 in bit-bang mode, GPIOL1 in MPSSE mode. |
| 15 | ADBUS6 | bidirectional | Channel A bit 6: DCD# in UART mode, D6 in bit-bang mode, GPIOL2 in MPSSE mode. |
| 16 | ADBUS7 | bidirectional | Channel A bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, D7 in bit-bang mode, GPIOL3 in MPSSE mode. |
| 17 | BDBUS0 | bidirectional | Channel B bit 0: TXD in UART mode, D0 in bit-bang mode, TCK/SK in MPSSE mode. |
| 18 | BDBUS1 | bidirectional | Channel B bit 1: RXD in UART mode, D1 in bit-bang mode, TDI/DO in MPSSE mode. |
| 19 | BDBUS2 | bidirectional | Channel B bit 2: RTS# in UART mode, D2 in bit-bang mode, TDO/DI in MPSSE mode. |
| 20 | BDBUS3 | bidirectional | Channel B bit 3: CTS# in UART mode, D3 in bit-bang mode, TMS/CS in MPSSE mode. |
| 21 | BDBUS4 | bidirectional | Channel B bit 4: DTR# in UART mode, D4 in bit-bang mode, GPIOL0 in MPSSE mode. |
| 22 | BDBUS5 | bidirectional | Channel B bit 5: DSR# in UART mode, D5 in bit-bang mode, GPIOL1 in MPSSE mode. |
| 23 | BDBUS6 | bidirectional | Channel B bit 6: DCD# in UART mode, D6 in bit-bang mode, GPIOL2 in MPSSE mode. |
| 24 | BDBUS7 | bidirectional | Channel B bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, D7 in bit-bang mode, GPIOL3 in MPSSE mode. |
| 25 | VCORE | power_in | +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator. |
| 26 | VCCIO | power_in | +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail. |
| 27 | OSCI | input | Oscillator input; a 12 MHz crystal is connected to OSCI and OSCO. |
| 28 | OSCO | output | Oscillator output; a 12 MHz crystal is connected to OSCI and OSCO. |
| 29 | GND | power_in | Ground. |
| 30 | VREGIN | power_in | +3.3V input to the integrated 1.2V voltage regulator. |
| 31 | VREGOUT | power_out | +1.2V integrated regulator output; connect to VCORE with a 3.3uF filter capacitor and do not use to power other circuits. |
| 32 | FSOURCE | power_in | FSOURCE input pin for EFUSE; leave floating for normal operation. |
| 33 | VPP | power_in | VPP input pin for EFUSE; leave floating for normal operation. |
| 34 | CDBUS0 | bidirectional | Channel C bit 0: TXD in UART mode or D0 in bit-bang mode. |
| 35 | CDBUS1 | bidirectional | Channel C bit 1: RXD in UART mode or D1 in bit-bang mode. |
| 36 | CDBUS2 | bidirectional | Channel C bit 2: RTS# in UART mode or D2 in bit-bang mode. |
| 37 | CDBUS3 | bidirectional | Channel C bit 3: CTS# in UART mode or D3 in bit-bang mode. |
| 38 | CDBUS4 | bidirectional | Channel C bit 4: DTR# in UART mode or D4 in bit-bang mode. |
| 39 | VCCIO | power_in | +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail. |
| 40 | CDBUS5 | bidirectional | Channel C bit 5: DSR# in UART mode or D5 in bit-bang mode. |
| 41 | CDBUS6 | bidirectional | Channel C bit 6: DCD# in UART mode or D6 in bit-bang mode. |
| 42 | CDBUS7 | bidirectional | Channel C bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, or D7 in bit-bang mode. |
| 43 | SUSPEND# | output | Active-low output that is low when USB is in suspend mode. |
| 44 | VCORE | power_in | +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator. |
| 45 | DDBUS0 | bidirectional | Channel D bit 0: TXD in UART mode or D0 in bit-bang mode. |
| 46 | DDBUS1 | bidirectional | Channel D bit 1: RXD in UART mode or D1 in bit-bang mode. |
| 47 | DDBUS2 | bidirectional | Channel D bit 2: RTS# in UART mode or D2 in bit-bang mode. |
| 48 | DDBUS3 | bidirectional | Channel D bit 3: CTS# in UART mode or D3 in bit-bang mode. |
| 49 | DDBUS4 | bidirectional | Channel D bit 4: DTR# in UART mode or D4 in bit-bang mode. |
| 50 | DDBUS5 | bidirectional | Channel D bit 5: DSR# in UART mode or D5 in bit-bang mode. |
| 51 | VCCIO | power_in | +3.3V I/O interface power supply input; all VCCIO pins must be connected or the device will fail. |
| 52 | DDBUS6 | bidirectional | Channel D bit 6: DCD# in UART mode or D6 in bit-bang mode. |
| 53 | DDBUS7 | bidirectional | Channel D bit 7: RI# or TXDEN (EEPROM selectable, default RI#) in UART mode, or D7 in bit-bang mode. |
| 54 | GPIO2 | bidirectional | GPIO2 or I2C_INT# pin whose default function is GPIO2 input with weak pull-down. |
| 55 | GPIO1 | bidirectional | GPIO1 or I2C_SCL pin whose default function is GPIO1 input with weak pull-down. |
| 56 | GPIO0 | bidirectional | GPIO0 or I2C_SDA pin whose default function is GPIO0 input with weak pull-down. |
| 57 | VCC_USB | power_in | +3.3V internal USB PHY supply input that cannot be connected directly to the USB supply; a +3.3V regulator is required and LC filtering is recommended. |
| 58 | DM | bidirectional | USB data signal minus. |
| 59 | DP | bidirectional | USB data signal plus. |
| 60 | REF | input | Current reference input; connect via a 12K Ohm 1% resistor to GND. |
| 61 | VCC_PD | power_in | +3.3V internal PD PHY power supply input. |
| 62 | PD1_CC2 | bidirectional | Analog I/O pin for the PD1 CC2 line. |
| 63 | PD1_SVBUS | input | Analog input for scaled-down PD1 VBUS sensing; VBUS must be divided by 10 before this pin. |
| 64 | PD1_VCONN | power_in | Power input for the PD1 VCONN power source; connect to 3.3V. |
| 65 | PD1_CC1 | bidirectional | Analog I/O pin for the PD1 CC1 line. |
| 66 | VCORE | power_in | +1.2V core supply voltage input; connect to VREGOUT when using the internal regulator. |
| 67 | PWREN# | output | Active-low power-enable output: 0 = normal operation, 1 = USB suspend or device not configured. |
| 68 | EECS | bidirectional | EEPROM chip select, tri-state during device reset; pull to VCCIO via 10K if no EEPROM. |
| 69 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FTDI |
| Package | QFN-68(8x8) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 69 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | | -65 | | 150 | °C | | 27 |
| Ambient Operating Temperature (Power Applied) | | -40 | | 85 | °C | Power Applied | 27 |
| VCORE Supply Voltage | VCORE | -0.3 | | 2 | V | | 27 |
| VCCIO IO Voltage | VCCIO | -0.3 | | 4 | V | | 27 |
| DC Input Voltage, USBDP and USBDM | | -0.5 | | 3.63 | V | | 27 |
| DC Input Voltage, High Impedance Bi-directional (powered from VCCIO) | | -0.3 | | 5.8 | V | powered from VCCIO | 27 |
| DC Input Voltage, All Other Inputs | | -0.5 | | | V | max is + (VCCIO +0.5) | 27 |
| DC Output Current, Outputs | | | | 16 | mA | | 27 |
| VCORE VCC Core Operating Supply Voltage | VCORE | 1.08 | 1.2 | 1.32 | V | | 27 |
| VCCIO Operating Supply Voltage | VCCIO | 2.97 | 3.3 | 3.63 | V | | 27 |
| VREGIN Voltage regulator Input | VREGIN | 3 | 3.3 | 3.6 | V | | 27 |
| VREGOUT Voltage regulator Output | VREGOUT | 1.08 | 1.2 | 1.32 | V | | 27 |
| Regulator Current | Ireg | 21.11 | | 150 | mA | VREGIN +3.3V and data transfer with 12Mbps | 27 |
| VREGIN Suspend Supply Current | Icc1s | | 1.64 | | mA | USB Suspend | 27 |
| VCC_USB operating supply current | I_vcd_usb | | 22.7 | | mA | Data transfer with 12Mbps | 27 |
| VCC_IO operating supply current | I_vccio | | 0.87 | | mA | Data transfer with 12Mbps | 27 |
| VCC_PD suspend supply current | I_vcc_pd | | 209 | | uA | PD suspend | 27 |
| Output Voltage High | Voh | 2.4 | 3.14 | | V | Ioh = +/-2mA | 28 |
| Output Voltage High | Voh | 3.2 | | | V | I/O Drive strength* = 8mA | 28 |
| Output Voltage High | Voh | 3.22 | | | V | I/O Drive strength* = 12mA | 28 |
| Output Voltage Low | Vol | | 0.18 | 0.4 | V | Iol = +/-2mA | 28 |
| Output Voltage Low | Vol | | | 0.12 | V | I/O Drive strength* = 8mA | 28 |
| Output Voltage Low | Vol | | | 0.08 | V | I/O Drive strength* = 12mA | 28 |
| Output Voltage Low | Vol | | | 0.07 | V | I/O Drive strength* = 16mA | 28 |
| Input low Switching Threshold | Vil | | | 0.8 | V | LVTTL | 28 |
| Input High Switching Threshold | Vih | 2 | | | V | LVTTL | 28 |
| Schmitt trigger negative going threshold voltage | Vt- | 0.8 | 1.1 | | V | | 28 |
| Schmitt trigger positive going threshold voltage | Vt+ | 1.6 | | 2 | V | | 28 |
| Input pull-up resistance | Rpu | 40 | 75 | 190 | KΩ | Vin = 0 | 28 |
| Input pull-down resistance | Rpd | 40 | 75 | 190 | KΩ | Vin =VCCIO | 28 |
| Input Leakage Current | Iin | 15 | 45 | 85 | μA | Vin = 0 | 28 |
| Tri-state output leakage current | Ioz | -10 | | 10 | μA | Vin = 5.5V or 0 | 28 |
| Human Body Model (HBM) | | -2 | | 2 | kV | ANSI/ESDA/JEDEC JS-001 Class 2 | 28 |
| Machine Mode (MM) | | -200 | | 200 | V | JEDEC EIA/JESD22-A115-C, Class B | 28 |
| Charge Device Model (CDM) | | -500 | | 500 | V | ANSI/ESDA/JEDEC JS-002, JEDEC JESD22-C101-D Class-III | 28 |
| Latch-up | | -200 | | 200 | mA | JEDEC STANDARD EIA/JESD78, Trigger Class-II | 28 |
| TJ Junction Temperature (FT4232HPQ) | TJ | -40 | 25 | 125 | °C | FT4233HPL/FT4233HPQ/FT4232HPQ | 29 |
| ѲJA Thermal Resistance Junction-to-Ambient (FT4232HPQ) | ѲJA | | 23.65 | | °C/W | Preliminary data | 29 |
| ѲJC Thermal Resistance Junction-to-Case (FT4232HPQ) | ѲJC | | 9.35 | | °C/W | Preliminary data | 29 |
## CAD (KiCad official)
- Symbol: `FT4232HPQ-TRAY`
- Footprint: `Package_DFN_QFN:QFN-68-1EP_8x8mm_P0.4mm_EP5.2x5.2mm`
- 3D model: QFN-68(8x8) (KiCad packages3D, STEP)
- 3D model files: `ft4232hpq-tray-etched.step` / `ft4232hpq-tray-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ft4232hpq-tray.step` / `ft4232hpq-tray.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [FTDI datasheet](docs/ft4232hpq-tray-datasheet.pdf) (39 pp, sha256 `4394e4c473a80dcf`, retrieved 2026-11-02, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ft4232hpq-tray-datasheet.pdf)