component
FT24C64A-TTR-T
Public Made by Adomby adom
FMD(Fremont Micro Devices) EEPROM, TSSOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
7239beb
FT24C64A-TTR-T
FMD(Fremont Micro Devices) · EEPROM · TSSOP-8
FT24C64A-TTR-T from FMD(Fremont Micro Devices), in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Device address input hardwired to VIH or VIL for chip select, and internally recognized as VIL if left unconnected. |
| 2 | A1 | input | Device address input hardwired to VIH or VIL for chip select, and internally recognized as VIL if left unconnected. |
| 3 | A2 | input | Device address input hardwired to VIH or VIL for chip select, and internally recognized as VIL if left unconnected. |
| 4 | GND | power_in | Ground. |
| 5 | SDA | bidirectional | Serial data line, a bi-directional open-drain signal that can be wired-OR with other open-drain devices and is typically pulled high by an external resistor. |
| 6 | SCL | input | Serial clock input whose rising edge latches data into the EEPROM and whose falling edge clocks data out. |
| 7 | WP | input | Write protect input that disables all programming when connected to VIH or VCC, and allows programming when left unconnected or at VIL. |
| 8 | VCC | power_in | Power supply, 1.8V to 5.5V, with a decoupling capacitor of at least 10nF recommended. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FMD(Fremont Micro Devices) |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Clock frequency, SCL (1.8V) | fSCL | 400 | kHz | VCC 1.8V | 9 | ||
| Clock frequency, SCL (2.5-5.5V) | fSCL | 1000 | kHz | VCC 2.5-5.5V | 9 | ||
| Clock pulse width low (1.8V) | tLOW | 1.2 | µs | VCC 1.8V | 9 | ||
| Clock pulse width low (2.5-5.5V) | tLOW | 0.6 | µs | VCC 2.5-5.5V | 9 | ||
| Clock pulse width high (1.8V) | tHIGH | 0.4 | µs | VCC 1.8V | 9 | ||
| Clock pulse width high (2.5-5.5V) | tHIGH | 0.3 | µs | VCC 2.5-5.5V | 9 | ||
| Noise suppression time (1.8V) | tI | 120 | ns | VCC 1.8V | 9 | ||
| Noise suppression time (2.5-5.5V) | tI | 120 | ns | VCC 2.5-5.5V | 9 | ||
| Clock low to data out valid (1.8V) | tAA | 1.2 | µs | VCC 1.8V | 9 | ||
| Clock low to data out valid (2.5-5.5V) | tAA | 0.55 | µs | VCC 2.5-5.5V | 9 | ||
| Time the bus must be free before a new transmission can start (1.8V) | tBUF | 1.3 | µs | VCC 1.8V | 9 | ||
| Time the bus must be free before a new transmission can start (2.5-5.5V) | tBUF | 1.2 | µs | VCC 2.5-5.5V | 9 | ||
| START hold time (1.8V) | tHD.STA | 0.6 | µs | VCC 1.8V | 9 | ||
| START hold time (2.5-5.5V) | tHD.STA | 0.6 | µs | VCC 2.5-5.5V | 9 | ||
| START set-up time (1.8V) | tSU.STA | 0.6 | µs | VCC 1.8V | 9 | ||
| START set-up time (2.5-5.5V) | tSU.STA | 0.6 | µs | VCC 2.5-5.5V | 9 | ||
| Data in hold time (1.8V) | tHD.DAT | 0 | µs | VCC 1.8V | 9 | ||
| Data in hold time (2.5-5.5V) | tHD.DAT | 0 | µs | VCC 2.5-5.5V | 9 | ||
| Data in set-up time (1.8V) | tSU.DAT | 100 | ns | VCC 1.8V | 9 | ||
| Data in set-up time (2.5-5.5V) | tSU.DAT | 100 | ns | VCC 2.5-5.5V | 9 | ||
| Input rise time (1.8V) | tR | 300 | ns | VCC 1.8V | 9 | ||
| Input rise time (2.5-5.5V) | tR | 300 | ns | VCC 2.5-5.5V | 9 | ||
| Input fall time (1.8V) | tF | 300 | ns | VCC 1.8V | 9 | ||
| Input fall time (2.5-5.5V) | tF | 300 | ns | VCC 2.5-5.5V | 9 | ||
| STOP set-up time (1.8V) | tSU.STO | 0.6 | µs | VCC 1.8V | 9 | ||
| STOP set-up time (2.5-5.5V) | tSU.STO | 0.6 | µs | VCC 2.5-5.5V | 9 | ||
| Data out hold time (1.8V) | tDH | 200 | ns | VCC 1.8V | 9 | ||
| Data out hold time (2.5-5.5V) | tDH | 50 | ns | VCC 2.5-5.5V | 9 | ||
| Vcc slew rate at power up (1.8V) | tPWR,R | 0.1 | 50 | V/ms | VCC 1.8V | 9 | |
| Vcc slew rate at power up (2.5-5.5V) | tPWR,R | 0.1 | 50 | V/ms | VCC 2.5-5.5V | 9 | |
| Time required after VCC is stable before the device can accept commands (1.8V) | tPUP | 100 | µs | VCC 1.8V | 9 | ||
| Time required after VCC is stable before the device can accept commands (2.5-5.5V) | tPUP | 100 | µs | VCC 2.5-5.5V | 9 | ||
| Minimum time at Vcc=0V between power cycles | tPOFF | 500 | ms | 9 | |||
| Write cycle time (1.8V) | tWR | 5 | ms | VCC 1.8V | 9 | ||
| Write cycle time (2.5-5.5V) | tWR | 5 | ms | VCC 2.5-5.5V | 9 | ||
| 24C××A supply VCC | VCC1 | 1.8 | 5.5 | V | 10 | ||
| Supply read current | ICC1 | 0.4 | 1 | mA | VCC @ 5.5V, SCL = 400 kHz | 10 | |
| Supply write current | ICC2 | 2 | 3 | mA | VCC @ 5.5V, SCL = 400 kHz | 10 | |
| Supply current | ISB1 | 1 | µA | VCC @ 1.8V, VIN = VCC or VSS | 10 | ||
| Input leakage current | IIL | 3 | µA | VIN = VCC or VSS | 10 | ||
| Output leakage current | ILO | 3 | µA | VIN = VCC or VSS | 10 | ||
| Input low level | VIL | -0.6 | V | 10 | |||
| Output low level | VOL1 | 0.2 | V | VCC @ 1.8V, IOL = 0.15 mA | 10 | ||
| Output low level | VOL2 | 0.4 | V | VCC @ 3.0V, IOL = 2.1 mA | 10 | ||
| Industrial operating temperature | -40 | 85 | ℃ | 2 | |||
| Storage temperature | -50 | 125 | ℃ | 2 | |||
| Input voltage on any pin relative to ground | -0.3 | V | relative to ground | 2 | |||
| Maximum voltage | 8 | V | 2 | ||||
| ESD Protection on all pins | 4000 | V | all pins | 2 | |||
| Supply decoupling capacitor on VCC pad | 10 | nF | connected to VCC PAD | 8 | |||
| VCC power-up slew rate | 0.05 | V/µs | monotonic rise from GND to minimum VCC | 8 |
CAD (KiCad official)
- Symbol:
FT24C64A-TTR-T - Footprint:
Package_SO:TSSOP-8_4.4x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
ft24c64a-ttr-t-etched.step/ft24c64a-ttr-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft24c64a-ttr-t.step/ft24c64a-ttr-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FMD(Fremont Micro Devices) datasheet (19 pp, sha256
479c1862c26e6caa, retrieved 2026-11-06, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text+vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# FT24C64A-TTR-T
**FMD(Fremont Micro Devices)** · EEPROM · TSSOP-8
FT24C64A-TTR-T from FMD(Fremont Micro Devices), in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | A0 | input | Device address input hardwired to VIH or VIL for chip select, and internally recognized as VIL if left unconnected. |
| 2 | A1 | input | Device address input hardwired to VIH or VIL for chip select, and internally recognized as VIL if left unconnected. |
| 3 | A2 | input | Device address input hardwired to VIH or VIL for chip select, and internally recognized as VIL if left unconnected. |
| 4 | GND | power_in | Ground. |
| 5 | SDA | bidirectional | Serial data line, a bi-directional open-drain signal that can be wired-OR with other open-drain devices and is typically pulled high by an external resistor. |
| 6 | SCL | input | Serial clock input whose rising edge latches data into the EEPROM and whose falling edge clocks data out. |
| 7 | WP | input | Write protect input that disables all programming when connected to VIH or VCC, and allows programming when left unconnected or at VIL. |
| 8 | VCC | power_in | Power supply, 1.8V to 5.5V, with a decoupling capacitor of at least 10nF recommended. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FMD(Fremont Micro Devices) |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Clock frequency, SCL (1.8V) | fSCL | | | 400 | kHz | VCC 1.8V | 9 |
| Clock frequency, SCL (2.5-5.5V) | fSCL | | | 1000 | kHz | VCC 2.5-5.5V | 9 |
| Clock pulse width low (1.8V) | tLOW | 1.2 | | | µs | VCC 1.8V | 9 |
| Clock pulse width low (2.5-5.5V) | tLOW | 0.6 | | | µs | VCC 2.5-5.5V | 9 |
| Clock pulse width high (1.8V) | tHIGH | 0.4 | | | µs | VCC 1.8V | 9 |
| Clock pulse width high (2.5-5.5V) | tHIGH | 0.3 | | | µs | VCC 2.5-5.5V | 9 |
| Noise suppression time (1.8V) | tI | | | 120 | ns | VCC 1.8V | 9 |
| Noise suppression time (2.5-5.5V) | tI | | | 120 | ns | VCC 2.5-5.5V | 9 |
| Clock low to data out valid (1.8V) | tAA | | | 1.2 | µs | VCC 1.8V | 9 |
| Clock low to data out valid (2.5-5.5V) | tAA | | | 0.55 | µs | VCC 2.5-5.5V | 9 |
| Time the bus must be free before a new transmission can start (1.8V) | tBUF | 1.3 | | | µs | VCC 1.8V | 9 |
| Time the bus must be free before a new transmission can start (2.5-5.5V) | tBUF | 1.2 | | | µs | VCC 2.5-5.5V | 9 |
| START hold time (1.8V) | tHD.STA | 0.6 | | | µs | VCC 1.8V | 9 |
| START hold time (2.5-5.5V) | tHD.STA | 0.6 | | | µs | VCC 2.5-5.5V | 9 |
| START set-up time (1.8V) | tSU.STA | 0.6 | | | µs | VCC 1.8V | 9 |
| START set-up time (2.5-5.5V) | tSU.STA | 0.6 | | | µs | VCC 2.5-5.5V | 9 |
| Data in hold time (1.8V) | tHD.DAT | 0 | | | µs | VCC 1.8V | 9 |
| Data in hold time (2.5-5.5V) | tHD.DAT | 0 | | | µs | VCC 2.5-5.5V | 9 |
| Data in set-up time (1.8V) | tSU.DAT | 100 | | | ns | VCC 1.8V | 9 |
| Data in set-up time (2.5-5.5V) | tSU.DAT | 100 | | | ns | VCC 2.5-5.5V | 9 |
| Input rise time (1.8V) | tR | | | 300 | ns | VCC 1.8V | 9 |
| Input rise time (2.5-5.5V) | tR | | | 300 | ns | VCC 2.5-5.5V | 9 |
| Input fall time (1.8V) | tF | | | 300 | ns | VCC 1.8V | 9 |
| Input fall time (2.5-5.5V) | tF | | | 300 | ns | VCC 2.5-5.5V | 9 |
| STOP set-up time (1.8V) | tSU.STO | 0.6 | | | µs | VCC 1.8V | 9 |
| STOP set-up time (2.5-5.5V) | tSU.STO | 0.6 | | | µs | VCC 2.5-5.5V | 9 |
| Data out hold time (1.8V) | tDH | 200 | | | ns | VCC 1.8V | 9 |
| Data out hold time (2.5-5.5V) | tDH | 50 | | | ns | VCC 2.5-5.5V | 9 |
| Vcc slew rate at power up (1.8V) | tPWR,R | 0.1 | | 50 | V/ms | VCC 1.8V | 9 |
| Vcc slew rate at power up (2.5-5.5V) | tPWR,R | 0.1 | | 50 | V/ms | VCC 2.5-5.5V | 9 |
| Time required after VCC is stable before the device can accept commands (1.8V) | tPUP | 100 | | | µs | VCC 1.8V | 9 |
| Time required after VCC is stable before the device can accept commands (2.5-5.5V) | tPUP | 100 | | | µs | VCC 2.5-5.5V | 9 |
| Minimum time at Vcc=0V between power cycles | tPOFF | 500 | | | ms | | 9 |
| Write cycle time (1.8V) | tWR | | | 5 | ms | VCC 1.8V | 9 |
| Write cycle time (2.5-5.5V) | tWR | | | 5 | ms | VCC 2.5-5.5V | 9 |
| 24C××A supply VCC | VCC1 | 1.8 | | 5.5 | V | | 10 |
| Supply read current | ICC1 | | 0.4 | 1 | mA | VCC @ 5.5V, SCL = 400 kHz | 10 |
| Supply write current | ICC2 | | 2 | 3 | mA | VCC @ 5.5V, SCL = 400 kHz | 10 |
| Supply current | ISB1 | | | 1 | µA | VCC @ 1.8V, VIN = VCC or VSS | 10 |
| Input leakage current | IIL | | | 3 | µA | VIN = VCC or VSS | 10 |
| Output leakage current | ILO | | | 3 | µA | VIN = VCC or VSS | 10 |
| Input low level | VIL | -0.6 | | | V | | 10 |
| Output low level | VOL1 | | | 0.2 | V | VCC @ 1.8V, IOL = 0.15 mA | 10 |
| Output low level | VOL2 | | | 0.4 | V | VCC @ 3.0V, IOL = 2.1 mA | 10 |
| Industrial operating temperature | | -40 | | 85 | ℃ | | 2 |
| Storage temperature | | -50 | | 125 | ℃ | | 2 |
| Input voltage on any pin relative to ground | | -0.3 | | | V | relative to ground | 2 |
| Maximum voltage | | | | 8 | V | | 2 |
| ESD Protection on all pins | | 4000 | | | V | all pins | 2 |
| Supply decoupling capacitor on VCC pad | | 10 | | | nF | connected to VCC PAD | 8 |
| VCC power-up slew rate | | | | 0.05 | V/µs | monotonic rise from GND to minimum VCC | 8 |
## CAD (KiCad official)
- Symbol: `FT24C64A-TTR-T`
- Footprint: `Package_SO:TSSOP-8_4.4x3mm_P0.65mm`
- 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files: `ft24c64a-ttr-t-etched.step` / `ft24c64a-ttr-t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ft24c64a-ttr-t.step` / `ft24c64a-ttr-t.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [FMD(Fremont Micro Devices) datasheet](docs/ft24c64a-ttr-t-datasheet.pdf) (19 pp, sha256 `479c1862c26e6caa`, retrieved 2026-11-06, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text+vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ft24c64a-ttr-t-datasheet.pdf)