main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ft24c16a-etr-t: viewers · Ray
ft24c16a-etr-t-etched.glb Publish 0.1.0 · Ray
ft24c16a-etr-t-etched.step ft24c16a-etr-t: factory component page (tier=lcsc) · Ray
ft24c16a-etr-t-hero.glb ft24c16a-etr-t: hero GLB from the etched model (keeps the MPN mark) · Ray
ft24c16a-etr-t-hero.overlay.json Publish 0.1.0 · Ray
ft24c16a-etr-t.glb Publish 0.1.0 · Ray
ft24c16a-etr-t.kicad_mod Publish 0.1.0 · Ray
ft24c16a-etr-t.kicad_sym Publish 0.1.0 · Ray
ft24c16a-etr-t.lbr Publish 0.1.0 · Ray
ft24c16a-etr-t.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier lcsc, 8 pins · Ray

FT24C16A-ETR-T

FMD(Fremont Micro Devices) · EEPROM · TSSOP-8

FT24C16A-ETR-T from FMD(Fremont Micro Devices), in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No-connect pin with no internal function stated in the datasheet.
2 NC unconnected No-connect pin with no internal function stated in the datasheet.
3 NC unconnected No-connect pin with no internal function stated in the datasheet.
4 GND power_in Ground.
5 SDA bidirectional Serial data line, bi-directional and open-drain output that can be wire-ORed with other open-drain devices and is typically pulled high by an external resistor.
6 SCL input Serial clock input whose rising edge latches data into the EEPROM and whose falling edge clocks data out.
7 WP input Write protect input that disables all programming when connected to VIH or VCC, allows programming when left unconnected or at VIL, and does not affect reads; FMD recommends tying it to a known state with 10kΩ or less.
8 VCC power_in Power supply, 1.8V to 5.5V, with a decoupling capacitor of no less than 10nF recommended.

Key specifications

Parameter Value
Manufacturer FMD(Fremont Micro Devices)
Package TSSOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Industrial operating temperature -40 85 ℃ 2
Storage temperature -50 125 ℃ 2
Input voltage on any pin relative to ground -0.3 V relative to ground; printed max is VCC + 0.3V 2
ESD protection on all pins 2000 V all pins; printed as >2000V 2
Power supply VCC VCC1 1.8 5.5 V 12
WP pin pull-up or pull-down resistor 10 kΩ FMD recommends 10kΩ or less 4
VCC pad decoupling capacitor 10 nF connected to VCC pad 10
Supply read current ICC1 0.5 1 mA VCC @ 5.0V SCL = 400 kHz 12
Supply write current ICC2 2 3 mA VCC @ 5.0V SCL = 400 kHz 12
Supply current ISB1 1 µA VCC @ 1.8V, VIN = VCC or VSS 12
Input leakage current IIL 3 µA VIN = VCC or VSS 12
Output leakage current ILO 3 µA VIN = VCC or VSS 12
Input low level VIL -0.6 V printed max is VCC × 0.3 12
Output low level VOL1 0.2 V VCC @ 1.8V, IOL = 0.15 mA 12
Output low level VOL2 0.4 V VCC @ 3.0V, IOL = 2.1 mA 12
Clock frequency, SCL fSCL 400 kHz 1.8 V 11
Clock frequency, SCL fSCL 1000 kHz 2.5V - 5.5V 11
Clock pulse width low tLOW 1.3 µs 1.8 V 11
Clock pulse width low tLOW 0.4 µs 2.5V - 5.5V 11
Clock pulse width high tHIGH 0.6 µs 1.8 V 11
Clock pulse width high tHIGH 0.4 µs 2.5V - 5.5V 11
Noise suppression time tI 50 ns 1.8 V 11
Clock low to data out valid tAA 0.2 0.9 µs 1.8 V 11
Clock low to data out valid tAA 0.2 0.55 µs 2.5V - 5.5V 11
Time the bus must be free before a new transmission can start tBUF 1.3 µs 1.8 V 11
Time the bus must be free before a new transmission can start tBUF 0.5 µs 2.5V - 5.5V 11
START hold time tHD.STA 0.6 µs 1.8 V 11
START hold time tHD.STA 0.25 µs 2.5V - 5.5V 11
START set-up time tSU.STA 0.6 µs 1.8 V 11
START set-up time tSU.STA 0.25 µs 2.5V - 5.5V 11
Data in hold time tHD.DAT 0 µs 1.8 V 11
Data in set-up time tSU.DAT 100 ns 1.8 V 11
Input rise time tR 0.3 µs 1.8 V 11
Input fall time tF 300 ns 1.8 V 11
Input fall time tF 100 ns 2.5V - 5.5V 11
STOP set-up time tSU.STO 0.6 µs 1.8 V 11
STOP set-up time tSU.STO 0.25 µs 2.5V - 5.5V 11
Data out hold time tDH 50 ns 1.8 V 11
Vcc slew rate at power up tPWR,R 0.1 50 V/ms 1.8 V 11
Time required after VCC is stable before the device can accept commands tPUP 100 µs 1.8 V 11
Minimum time at Vcc=0V between power cycles tPOFF 500 ms 1.8 V 11
Write cycle time tWR 5 ms 1.8 V 11

CAD (KiCad official)

  • Symbol: FT24C16A-ETR-T
  • Footprint: Package_SO:TSSOP-8_4.4x3mm_P0.65mm
  • 3D model: TSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: ft24c16a-etr-t-etched.step / ft24c16a-etr-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ft24c16a-etr-t.step / ft24c16a-etr-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: FMD(Fremont Micro Devices) datasheet (21 pp, sha256 4f2bb49911da356a, retrieved 2026-11-06, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text+vision), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF