main
Ray Publish 0.1.0 7bfc9d7

FT24C128A-ESR-B

FMD(Fremont Micro Devices) · EEPROM · SOP-8

FT24C128A-ESR-B from FMD(Fremont Micro Devices), in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
4 GND power_in Ground reference for the device; input voltage on any pin is rated -0.3V to VCC + 0.3V relative to ground.
5 SDA bidirectional Serial data line, a bi-directional open-drain signal that can be wired-OR with other open-drain devices and is typically pulled high by an external resistor.
6 SCL input Serial clock input where the rising edge latches data into the EEPROM and the falling edge clocks data out, with a maximum clock frequency of 400 kHz at 1.8V and 1000 kHz at 2.5-5.0V.
7 WP input Write protect input that disables all programming functions when connected to VIH or VCC, while programming is allowed when it is left unconnected or at VIL and reads are unaffected.
8 VCC power_in Power supply pin with an operating range of 1.8V to 5.5V.

Key specifications

Parameter Value
Manufacturer FMD(Fremont Micro Devices)
Package SOP-8
Category Memory
Pins 5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage (24C××A supply VCC) VCC1 1.8 5.5 V 9
Supply read current ICC 0.4 1 mA VCC @ 5.0V SCL = 100 kHz 9
Supply write current ICC 2 3 mA VCC @ 5.0V SCL = 100 kHz 9
Supply current ISB1 0.02 1 µA VCC @ 1.8V, VIN = VCC or VSS 9
Supply current ISB2 1 µA VCC @ 2.5V, VIN = VCC or VSS 9
Supply current ISB3 0.07 1 µA VCC @ 5.0V, VIN = VCC or VSS 9
Input leakage current IIL 3 µA VIN = VCC or VSS 9
Output leakage current ILO 3 µA VIN = VCC or VSS 9
Input low level VIL -0.6 V 9
Output low level VOL2 0.4 V VCC @ 3.0V, IOL = 2.1 mA 9
Clock frequency, SCL fSCL 400 kHz 1.8V column 8
Clock pulse width low tLOW 1.3 µs 1.8V column 8
Clock pulse width high tHIGH 0.6 µs 1.8V column 8
Noise suppression time tI 100 ns 1.8V column 8
Clock low to data out valid tAA 0.9 µs 1.8V column 8
Time the bus must be free before a new transmission can start tBUF 1.3 µs 1.8V column 8
START hold time tHD.STA 0.6 µs 1.8V column 8
START set-up time tSU.STA 0.6 µs 1.8V column 8
Data in hold time tHD.DAT 0 µs 1.8V column 8
Data in set-up time tSU.DAT 100 ns 1.8V column 8
Input rise time tR 0.3 µs 1.8V column 8
Input fall time tF 300 ns 1.8V column 8
STOP set-up time tSU.STO 0.6 µs 1.8V column 8
Data out hold time tDH 50 ns 1.8V column 8
Write cycle time tWR 5 ms 1.8V column 8
Clock frequency, SCL fSCL 1000 kHz 2.5-5.0 V column 8
Clock pulse width low tLOW 0.4 µs 2.5-5.0 V column 8
Clock pulse width high tHIGH 0.4 µs 2.5-5.0 V column 8
Noise suppression time tI 50 ns 2.5-5.0 V column 8
Clock low to data out valid tAA 0.55 µs 2.5-5.0 V column 8
Time the bus must be free before a new transmission can start tBUF 0.5 µs 2.5-5.0 V column 8
START hold time tHD.STA 0.25 µs 2.5-5.0 V column 8
START set-up time tSU.STA 0.25 µs 2.5-5.0 V column 8
Input fall time tF 100 ns 2.5-5.0 V column 8
STOP set-up time tSU.STO 0.25 µs 2.5-5.0 V column 8
Endurance (write cycles) 1e+06 Write Cycles 25oC, Page Mode, 3.3V 8
Industrial operating temperature -40 85 ℃ 2
Storage temperature -50 125 ℃ 2
Input voltage on any pin relative to ground -0.3 V relative to ground 2
Maximum voltage 8 V 2
ESD protection on all pins 2000 V all pins 2

CAD (KiCad official)

  • Symbol: FT24C128A-ESR-B
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOP-8 (KiCad packages3D, STEP)
  • 3D model files: ft24c128a-esr-b-etched.step / ft24c128a-esr-b-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ft24c128a-esr-b.step / ft24c128a-esr-b.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: FMD(Fremont Micro Devices) datasheet (16 pp, sha256 8365e4d4ae03832f, retrieved 2026-11-05, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF