main
Download ZIP Propose a change
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers ft24c02a-ktr-t: viewers · Ray
ft24c02a-ktr-t-etched.glb Publish 0.1.0 · Ray
ft24c02a-ktr-t-etched.step ft24c02a-ktr-t: factory component page (tier=lcsc) · Ray
ft24c02a-ktr-t-hero.glb ft24c02a-ktr-t: hero GLB from the etched model (keeps the MPN mark) · Ray
ft24c02a-ktr-t-hero.overlay.json Publish 0.1.0 · Ray
ft24c02a-ktr-t.glb Publish 0.1.0 · Ray
ft24c02a-ktr-t.kicad_mod Publish 0.1.0 · Ray
ft24c02a-ktr-t.kicad_sym Publish 0.1.0 · Ray
ft24c02a-ktr-t.lbr Publish 0.1.0 · Ray
ft24c02a-ktr-t.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray

FT24C02A-KTR-T

FMD(Fremont Micro Devices) · EEPROM · TSSOP-8

FT24C02A-KTR-T from FMD(Fremont Micro Devices), in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 A0 input Device address input that is matched against the device address bits and is internally recognized as VIL if left unconnected.
2 A1 input Device address input that is matched against the device address bits and is internally recognized as VIL if left unconnected.
3 A2 input Device address input that is matched against the device address bits and is internally recognized as VIL if left unconnected.
4 GND power_in Ground.
5 SDA bidirectional Serial data line, bi-directional with open-drain output that can be wired-OR with other open-drain devices and is typically pulled high by an external resistor.
6 SCL input Serial clock input where the rising edge latches data into the EEPROM and the falling edge clocks data out.
7 WP input Write protect input that disables all programming when tied to VIH or VCC, and allows programming when left unconnected or at VIL, with reads unaffected.
8 VCC power_in Power supply, 1.8V to 5.5V.

Key specifications

Parameter Value
Manufacturer FMD(Fremont Micro Devices)
Package TSSOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating temperature -40 85 ℃ Industrial 2
Storage temperature -50 125 ℃ 2
Input voltage on any pin relative to ground -0.3 V max VCC + 0.3V 2
Maximum voltage 8 V 2
ESD protection on all pins 2000 V >2000V 2
Power supply VCC1 1.8 5.5 V 11
Supply read current ICC 0.5 1 mA VCC @ 5.0V SCL = 400 kHz 11
Supply write current ICC 2 3 mA VCC @ 5.0V SCL = 400 kHz 11
Standby supply current ISB1 1 µA VCC @ 1.8V, VIN = VCC or VSS 11
Standby supply current ISB3 0.07 1 µA VCC @ 5.0V, VIN = VCC or VSS 11
Input leakage current IIL 3 µA VIN = VCC or VSS 11
Output leakage current ILO 3 µA VIN = VCC or VSS 11
Input low level VIL -0.6 0.3 V max VCC × 0.3 11
Input high level VIH 0.7 0.5 V min VCC × 0.7; max VCC + 0.5 11
Output low level VOL1 0.2 V VCC @ 1.8V, IOL = 0.15 mA 11
Output low level VOL2 0.4 V VCC @ 3.0V, IOL = 2.1 mA 11
Clock frequency, SCL fSCL 400 kHz 1.8 V 10
Clock frequency, SCL fSCL 1000 kHz 2.5-5.0 V 10
Clock pulse width low tLOW 1.3 µs 1.8 V 10
Clock pulse width low tLOW 0.4 µs 2.5-5.0 V 10
Clock pulse width high tHIGH 0.6 µs 1.8 V 10
Clock pulse width high tHIGH 0.4 µs 2.5-5.0 V 10
Noise suppression time tI 50 ns 1.8 V and 2.5-5.0 V 10
Clock low to data out valid tAA 0.2 0.9 µs 1.8 V 10
Clock low to data out valid tAA 0.2 0.55 µs 2.5-5.0 V 10
Time the bus must be free before a new transmission tBUF 1.3 µs 1.8 V 10
Time the bus must be free before a new transmission tBUF 0.5 µs 2.5-5.0 V 10
START hold time tHD.STA 0.6 µs 1.8 V 10
START hold time tHD.STA 0.25 µs 2.5-5.0 V 10
START set-up time tSU.STA 0.6 µs 1.8 V 10
START set-up time tSU.STA 0.25 µs 2.5-5.0 V 10
Data in hold time tHD.DAT 0 µs 1.8 V and 2.5-5.0 V 10
Data in set-up time tSU.DAT 100 ns 1.8 V and 2.5-5.0 V 10
Input rise time tR 0.3 µs 1.8 V and 2.5-5.0 V 10
Input fall time tF 300 ns 1.8 V 10
Input fall time tF 100 ns 2.5-5.0 V 10
STOP set-up time tSU.STO 0.6 µs 1.8 V 10
STOP set-up time tSU.STO 0.25 µs 2.5-5.0 V 10
Data out hold time tDH 50 ns 1.8 V and 2.5-5.0 V 10
Write cycle time WR 5 ms 1.8 V and 2.5-5.0 V 10
Endurance 1e+06 Write Cycles 25oC, Page Mode, 3.3V 10

CAD (KiCad official)

  • Symbol: FT24C02A-KTR-T
  • Footprint: Package_SO:TSSOP-8_3x3mm_P0.65mm
  • 3D model: TSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: ft24c02a-ktr-t-etched.step / ft24c02a-ktr-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); ft24c02a-ktr-t.step / ft24c02a-ktr-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: FMD(Fremont Micro Devices) datasheet (20 pp, sha256 f7d42d5522251805, retrieved 2026-10-23, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF