component
FT245RNL-REEL
Public Made by Adomby adom
FTDI USB Converters, SSOP-28. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
30a5204
FT245RNL-REEL
FTDI · USB Converters · SSOP-28
FT245RNL-REEL from FTDI, in a SSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | D0 | bidirectional | FIFO Data Bus Bit 0. |
| 2 | D4 | bidirectional | FIFO Data Bus Bit 4. |
| 3 | D2 | bidirectional | FIFO Data Bus Bit 2. |
| 4 | VCCIO | power_in | +1.8V to +5.25V supply to the FIFO interface group pins; connect to 3V3OUT for +3.3V levels or to VCC for 5V CMOS levels in bus powered designs. |
| 5 | D1 | bidirectional | FIFO Data Bus Bit 1. |
| 6 | D7 | bidirectional | FIFO Data Bus Bit 7. |
| 7 | GND | power_in | Device ground supply pin. |
| 8 | NC | unconnected | No internal connection. |
| 9 | D5 | bidirectional | FIFO Data Bus Bit 5. |
| 10 | D6 | bidirectional | FIFO Data Bus Bit 6. |
| 11 | D3 | bidirectional | FIFO Data Bus Bit 3. |
| 12 | PWREN# | output | Goes low after the device is configured by USB, then high during USB suspend; should be pulled to VCCIO with a 10kΩ resistor when used to control an external P-channel MOSFET power switch. |
| 13 | RD# | input | Enables the current FIFO data byte on D0...D7 when low and fetches the next byte from the receive FIFO buffer when RD# goes from high to low. |
| 14 | WR | input | Writes the data byte on D0...D7 into the transmit FIFO buffer when WR goes from high to low. |
| 15 | USBDP | bidirectional | USB Data Signal Plus, incorporating internal series resistor and 1.5kΩ pull up resistor to 3.3V. |
| 16 | USBDM | bidirectional | USB Data Signal Minus, incorporating internal series resistor. |
| 17 | 3V3OUT | power_out | +3.3V output from the integrated LDO regulator, decoupled with 100nF, able to supply up to 50mA to external logic and usable to supply VCCIO. |
| 18 | GND | power_in | Device ground supply pin. |
| 19 | RESET# | input | Active low reset pin for an external device to reset the FT245RN; can be left unconnected or pulled up to VCC if not required. |
| 20 | VCC | power_in | +3.3V to +5.25V supply to the device core. |
| 21 | GND | power_in | Device ground supply pin. |
| 22 | TXE# | output | When high, do not write data into the FIFO; when low, data can be written by strobing WR high then low; tri-state during reset. |
| 23 | RXF# | output | When high, do not read from the FIFO; when low, data is available to read by strobing RD# low then high; tri-state during reset and becomes an input during suspend if Remote Wakeup is enabled. |
| 24 | NC | unconnected | No internal connection. |
| 25 | AGND | power_in | Device analogue ground supply for the internal clock multiplier. |
| 26 | TEST | input | Puts the device into IC test mode; must be tied to GND for normal operation, otherwise the device will appear to fail. |
| 27 | OSCI | input | Input 12MHz oscillator cell; optional and can be left unconnected for normal operation. |
| 28 | OSCO | output | Output from 12MHz oscillator cell; optional and can be left unconnected for normal operation if the internal oscillator is used. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FTDI |
| Package | SSOP-28 |
| Category | Communication Interface Chip |
| Pins | 28 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | -65 | 150 | °C | 15 | |||
| Floor Life (Out of Bag) At Factory Ambient (30°C / 60% RH) | 168 | hours | At factory ambient (30°C / 60% RH); IPC/JEDEC J-STD-033A MSL Level 3 | 15 | |||
| Ambient Temperature (Power Applied) | -40 | 85 | °C | Power applied | 15 | ||
| VCC Supply Voltage | VCC | -0.5 | 6 | V | 15 | ||
| DC Input Voltage, USBDP and USBDM | -0.5 | 3.8 | V | 15 | |||
| DC Input Voltage, High Impedance Bidirectional | -0.5 | V | Printed max is + (VCC +0.5) | 15 | |||
| DC Input Voltage, All Other Inputs | -0.5 | V | Printed max is + (VCC +0.5) | 15 | |||
| DC Output Current, Outputs | 24 | mA | 15 | ||||
| Power Dissipation | 500 | mW | VCC = 5.25V | 15 | |||
| VCC Operating Supply Voltage | VCC1 | 3.3 | 5.25 | V | 15 | ||
| VCCIO Operating Supply Voltage | VCC2 | 1.8 | 5.25 | V | 15 | ||
| Operating Supply Current, Normal Operation | Icc1 | 15 | mA | Normal Operation | 15 | ||
| Operating Supply Current, USB Suspend | Icc2 | 50 | 70 | 100 | μA | USB Suspend | 15 |
| 3.3V regulator output | 3V3 | 3 | 3.3 | 3.6 | V | 15 | |
| Output Voltage High (VCCIO = +5.0V, Standard Drive Level) | Voh | 3.2 | 4.1 | 4.9 | V | I source = 2mA | 15 |
| Output Voltage Low (VCCIO = +5.0V, Standard Drive Level) | Vol | 0.3 | 0.4 | 0.6 | V | I sink = 2mA | 15 |
| Input Switching Threshold (VCCIO = +5.0V, Standard Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 15 |
| Input Switching Hysteresis (VCCIO = +5.0V, Standard Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 15 |
| Output Voltage High (VCCIO = +3.3V, Standard Drive Level) | Voh | 2.2 | 2.7 | 3.2 | V | I source = 1mA | 16 |
| Output Voltage Low (VCCIO = +3.3V, Standard Drive Level) | Vol | 0.3 | 0.4 | 0.5 | V | I sink = 2mA | 16 |
| Input Switching Threshold (VCCIO = +3.3V, Standard Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +3.3V, Standard Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +2.8V, Standard Drive Level) | Voh | 2.1 | 2.6 | 2.8 | V | I source = 1mA | 16 |
| Output Voltage Low (VCCIO = +2.8V, Standard Drive Level) | Vol | 0.3 | 0.4 | 0.5 | V | I sink = 2mA | 16 |
| Input Switching Threshold (VCCIO = +2.8V, Standard Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +2.8V, Standard Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +1.8V, Standard Drive Level) | Voh | 1.32 | 1.62 | 1.8 | V | I source = 0.2mA | 16 |
| Output Voltage Low (VCCIO = +1.8V, Standard Drive Level) | Vol | 0.06 | 0.1 | 0.18 | V | I sink = 0.5mA | 16 |
| Input Switching Threshold (VCCIO = +1.8V, Standard Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +1.8V, Standard Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +5.0V, High Drive Level) | Voh | 3.2 | 4.1 | 4.9 | V | I source = 6mA | 16 |
| Output Voltage Low (VCCIO = +5.0V, High Drive Level) | Vol | 0.3 | 0.4 | 0.6 | V | I sink = 6mA | 16 |
| Input Switching Threshold (VCCIO = +5.0V, High Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +5.0V, High Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +3.3V, High Drive Level) | Voh | 2.2 | 2.8 | 3.2 | V | I source = 3mA | 16 |
| Output Voltage Low (VCCIO = +3.3V, High Drive Level) | Vol | 0.3 | 0.4 | 0.6 | V | I sink = 8mA | 16 |
| Input Switching Threshold (VCCIO = +3.3V, High Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +3.3V, High Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +2.8V, High Drive Level) | Voh | 2.1 | 2.6 | 2.8 | V | I source = 3mA | 16 |
| Output Voltage Low (VCCIO = +2.8V, High Drive Level) | Vol | 0.3 | 0.4 | 0.6 | V | I sink = 8mA | 16 |
| Input Switching Threshold (VCCIO = +2.8V, High Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +2.8V, High Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +1.8V, High Drive Level) | Voh | 1.35 | 1.67 | 1.8 | V | I source = 0.4mA | 17 |
| Output Voltage Low (VCCIO = +1.8V, High Drive Level) | Vol | 0.12 | 0.18 | 0.35 | V | I sink = 3mA | 17 |
| Input Switching Threshold (VCCIO = +1.8V, High Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 17 |
| Input Switching Hysteresis (VCCIO = +1.8V, High Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 17 |
| RESET# and TEST Input Switching Threshold | Vin | 1.3 | 1.6 | 1.9 | V | 17 | |
| RESET# and TEST Input Switching Hysteresis | VHys | 50 | 55 | 60 | mV | 17 | |
| I/O Pins Static Output (High) | UVoh | 2.8 | 3.6 | V | RI = 1.5kΩ to 3V3OUT (D+), RI = 15KΩ to GND (D-) | 17 | |
| I/O Pins Static Output (Low) | UVol | 0 | 0.3 | V | RI = 1.5kΩ to 3V3OUT (D+), RI = 15kΩ to GND (D-) | 17 | |
| Single Ended Rx Threshold | UVse | 0.8 | 2 | V | 17 | ||
| Differential Common Mode | UCom | 0.8 | 2.5 | V | 17 | ||
| Driver Output Impedance | UDrvZ | 26 | 29 | 44 | Ohms | 17 | |
| Frequency of Operation | 11.98 | 12 | 12.02 | MHz | Internal clock oscillator (see Note 1) | 17 | |
| Clock Period | 83.19 | 83.33 | 83.47 | ns | 17 | ||
| Duty Cycle | 45 | 50 | 55 | % | 17 | ||
| Thermal Resistance Junction-to-Ambient (FT245RNL) | ΘJA | 81.36 | °C/W | 18 | |||
| Thermal Resistance Junction-to-Case (FT245RNL) | ΘJC | 49.58 | °C/W | 18 |
CAD (KiCad official)
- Symbol:
FT245RNL-REEL - Footprint:
Package_SO:SSOP-28_5.3x10.2mm_P0.65mm - 3D model: SSOP-28 (KiCad packages3D, STEP)
- 3D model files:
ft245rnl-reel-etched.step/ft245rnl-reel-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft245rnl-reel.step/ft245rnl-reel.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FTDI datasheet (36 pp, sha256
45dc0b8b61dc4076, retrieved 2026-10-28, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# FT245RNL-REEL
**FTDI** · USB Converters · SSOP-28
FT245RNL-REEL from FTDI, in a SSOP-28. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | D0 | bidirectional | FIFO Data Bus Bit 0. |
| 2 | D4 | bidirectional | FIFO Data Bus Bit 4. |
| 3 | D2 | bidirectional | FIFO Data Bus Bit 2. |
| 4 | VCCIO | power_in | +1.8V to +5.25V supply to the FIFO interface group pins; connect to 3V3OUT for +3.3V levels or to VCC for 5V CMOS levels in bus powered designs. |
| 5 | D1 | bidirectional | FIFO Data Bus Bit 1. |
| 6 | D7 | bidirectional | FIFO Data Bus Bit 7. |
| 7 | GND | power_in | Device ground supply pin. |
| 8 | NC | unconnected | No internal connection. |
| 9 | D5 | bidirectional | FIFO Data Bus Bit 5. |
| 10 | D6 | bidirectional | FIFO Data Bus Bit 6. |
| 11 | D3 | bidirectional | FIFO Data Bus Bit 3. |
| 12 | PWREN# | output | Goes low after the device is configured by USB, then high during USB suspend; should be pulled to VCCIO with a 10kΩ resistor when used to control an external P-channel MOSFET power switch. |
| 13 | RD# | input | Enables the current FIFO data byte on D0...D7 when low and fetches the next byte from the receive FIFO buffer when RD# goes from high to low. |
| 14 | WR | input | Writes the data byte on D0...D7 into the transmit FIFO buffer when WR goes from high to low. |
| 15 | USBDP | bidirectional | USB Data Signal Plus, incorporating internal series resistor and 1.5kΩ pull up resistor to 3.3V. |
| 16 | USBDM | bidirectional | USB Data Signal Minus, incorporating internal series resistor. |
| 17 | 3V3OUT | power_out | +3.3V output from the integrated LDO regulator, decoupled with 100nF, able to supply up to 50mA to external logic and usable to supply VCCIO. |
| 18 | GND | power_in | Device ground supply pin. |
| 19 | RESET# | input | Active low reset pin for an external device to reset the FT245RN; can be left unconnected or pulled up to VCC if not required. |
| 20 | VCC | power_in | +3.3V to +5.25V supply to the device core. |
| 21 | GND | power_in | Device ground supply pin. |
| 22 | TXE# | output | When high, do not write data into the FIFO; when low, data can be written by strobing WR high then low; tri-state during reset. |
| 23 | RXF# | output | When high, do not read from the FIFO; when low, data is available to read by strobing RD# low then high; tri-state during reset and becomes an input during suspend if Remote Wakeup is enabled. |
| 24 | NC | unconnected | No internal connection. |
| 25 | AGND | power_in | Device analogue ground supply for the internal clock multiplier. |
| 26 | TEST | input | Puts the device into IC test mode; must be tied to GND for normal operation, otherwise the device will appear to fail. |
| 27 | OSCI | input | Input 12MHz oscillator cell; optional and can be left unconnected for normal operation. |
| 28 | OSCO | output | Output from 12MHz oscillator cell; optional and can be left unconnected for normal operation if the internal oscillator is used. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FTDI |
| Package | SSOP-28 |
| Category | Communication Interface Chip |
| Pins | 28 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Storage Temperature | | -65 | | 150 | °C | | 15 |
| Floor Life (Out of Bag) At Factory Ambient (30°C / 60% RH) | | | | 168 | hours | At factory ambient (30°C / 60% RH); IPC/JEDEC J-STD-033A MSL Level 3 | 15 |
| Ambient Temperature (Power Applied) | | -40 | | 85 | °C | Power applied | 15 |
| VCC Supply Voltage | VCC | -0.5 | | 6 | V | | 15 |
| DC Input Voltage, USBDP and USBDM | | -0.5 | | 3.8 | V | | 15 |
| DC Input Voltage, High Impedance Bidirectional | | -0.5 | | | V | Printed max is + (VCC +0.5) | 15 |
| DC Input Voltage, All Other Inputs | | -0.5 | | | V | Printed max is + (VCC +0.5) | 15 |
| DC Output Current, Outputs | | | | 24 | mA | | 15 |
| Power Dissipation | | | | 500 | mW | VCC = 5.25V | 15 |
| VCC Operating Supply Voltage | VCC1 | 3.3 | | 5.25 | V | | 15 |
| VCCIO Operating Supply Voltage | VCC2 | 1.8 | | 5.25 | V | | 15 |
| Operating Supply Current, Normal Operation | Icc1 | | 15 | | mA | Normal Operation | 15 |
| Operating Supply Current, USB Suspend | Icc2 | 50 | 70 | 100 | μA | USB Suspend | 15 |
| 3.3V regulator output | 3V3 | 3 | 3.3 | 3.6 | V | | 15 |
| Output Voltage High (VCCIO = +5.0V, Standard Drive Level) | Voh | 3.2 | 4.1 | 4.9 | V | I source = 2mA | 15 |
| Output Voltage Low (VCCIO = +5.0V, Standard Drive Level) | Vol | 0.3 | 0.4 | 0.6 | V | I sink = 2mA | 15 |
| Input Switching Threshold (VCCIO = +5.0V, Standard Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 15 |
| Input Switching Hysteresis (VCCIO = +5.0V, Standard Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 15 |
| Output Voltage High (VCCIO = +3.3V, Standard Drive Level) | Voh | 2.2 | 2.7 | 3.2 | V | I source = 1mA | 16 |
| Output Voltage Low (VCCIO = +3.3V, Standard Drive Level) | Vol | 0.3 | 0.4 | 0.5 | V | I sink = 2mA | 16 |
| Input Switching Threshold (VCCIO = +3.3V, Standard Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +3.3V, Standard Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +2.8V, Standard Drive Level) | Voh | 2.1 | 2.6 | 2.8 | V | I source = 1mA | 16 |
| Output Voltage Low (VCCIO = +2.8V, Standard Drive Level) | Vol | 0.3 | 0.4 | 0.5 | V | I sink = 2mA | 16 |
| Input Switching Threshold (VCCIO = +2.8V, Standard Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +2.8V, Standard Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +1.8V, Standard Drive Level) | Voh | 1.32 | 1.62 | 1.8 | V | I source = 0.2mA | 16 |
| Output Voltage Low (VCCIO = +1.8V, Standard Drive Level) | Vol | 0.06 | 0.1 | 0.18 | V | I sink = 0.5mA | 16 |
| Input Switching Threshold (VCCIO = +1.8V, Standard Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +1.8V, Standard Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +5.0V, High Drive Level) | Voh | 3.2 | 4.1 | 4.9 | V | I source = 6mA | 16 |
| Output Voltage Low (VCCIO = +5.0V, High Drive Level) | Vol | 0.3 | 0.4 | 0.6 | V | I sink = 6mA | 16 |
| Input Switching Threshold (VCCIO = +5.0V, High Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +5.0V, High Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +3.3V, High Drive Level) | Voh | 2.2 | 2.8 | 3.2 | V | I source = 3mA | 16 |
| Output Voltage Low (VCCIO = +3.3V, High Drive Level) | Vol | 0.3 | 0.4 | 0.6 | V | I sink = 8mA | 16 |
| Input Switching Threshold (VCCIO = +3.3V, High Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +3.3V, High Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +2.8V, High Drive Level) | Voh | 2.1 | 2.6 | 2.8 | V | I source = 3mA | 16 |
| Output Voltage Low (VCCIO = +2.8V, High Drive Level) | Vol | 0.3 | 0.4 | 0.6 | V | I sink = 8mA | 16 |
| Input Switching Threshold (VCCIO = +2.8V, High Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Input Switching Hysteresis (VCCIO = +2.8V, High Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 16 |
| Output Voltage High (VCCIO = +1.8V, High Drive Level) | Voh | 1.35 | 1.67 | 1.8 | V | I source = 0.4mA | 17 |
| Output Voltage Low (VCCIO = +1.8V, High Drive Level) | Vol | 0.12 | 0.18 | 0.35 | V | I sink = 3mA | 17 |
| Input Switching Threshold (VCCIO = +1.8V, High Drive Level) | Vin | 1 | 1.2 | 1.5 | V | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 17 |
| Input Switching Hysteresis (VCCIO = +1.8V, High Drive Level) | VHys | 20 | 25 | 30 | mV | ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO | 17 |
| RESET# and TEST Input Switching Threshold | Vin | 1.3 | 1.6 | 1.9 | V | | 17 |
| RESET# and TEST Input Switching Hysteresis | VHys | 50 | 55 | 60 | mV | | 17 |
| I/O Pins Static Output (High) | UVoh | 2.8 | | 3.6 | V | RI = 1.5kΩ to 3V3OUT (D+), RI = 15KΩ to GND (D-) | 17 |
| I/O Pins Static Output (Low) | UVol | 0 | | 0.3 | V | RI = 1.5kΩ to 3V3OUT (D+), RI = 15kΩ to GND (D-) | 17 |
| Single Ended Rx Threshold | UVse | 0.8 | | 2 | V | | 17 |
| Differential Common Mode | UCom | 0.8 | | 2.5 | V | | 17 |
| Driver Output Impedance | UDrvZ | 26 | 29 | 44 | Ohms | | 17 |
| Frequency of Operation | | 11.98 | 12 | 12.02 | MHz | Internal clock oscillator (see Note 1) | 17 |
| Clock Period | | 83.19 | 83.33 | 83.47 | ns | | 17 |
| Duty Cycle | | 45 | 50 | 55 | % | | 17 |
| Thermal Resistance Junction-to-Ambient (FT245RNL) | ΘJA | | 81.36 | | °C/W | | 18 |
| Thermal Resistance Junction-to-Case (FT245RNL) | ΘJC | | 49.58 | | °C/W | | 18 |
## CAD (KiCad official)
- Symbol: `FT245RNL-REEL`
- Footprint: `Package_SO:SSOP-28_5.3x10.2mm_P0.65mm`
- 3D model: SSOP-28 (KiCad packages3D, STEP)
- 3D model files: `ft245rnl-reel-etched.step` / `ft245rnl-reel-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ft245rnl-reel.step` / `ft245rnl-reel.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [FTDI datasheet](docs/ft245rnl-reel-datasheet.pdf) (36 pp, sha256 `45dc0b8b61dc4076`, retrieved 2026-10-28, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ft245rnl-reel-datasheet.pdf)