component
FT232BL-JSM
Public Made by Adomby adom
JSMSEMI USB ICs, QFP-32(7x7). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
6e816b3
FT232BL-JSM
JSMSEMI · USB ICs · QFP-32(7x7)
FT232BL-JSM from JSMSEMI, in a QFP-32(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EESK | output | Clock signal to the EEPROM, tri-stated during device reset and driven otherwise; a 10K pull-down on EESK makes the device use USB product ID 6004 (hex) instead of 6001. |
| 2 | EEDATA | bidirectional | EEPROM data I/O connected to the EEPROM data input directly and to its data output through a 2.2K resistor, with the EEPROM data output pulled up to VCC by 10K; tri-stated during device reset. |
| 3 | VCC | power_in | +4.35V to +5.25V supply to the device core, LDO and non-UART interface pins. |
| 4 | RESET# | input | Input that lets an external device reset the FT232BL; connect to VCC if not needed. |
| 5 | RSTOUT# | output | Internal reset generator output that stays high impedance for about 5ms after VCC exceeds 3.5V, then clamps to the 3.3V regulator output; also driven low when RESET# is low and unaffected by USB bus reset. |
| 6 | 3V3OUT | power_out | Output of the integrated 3.3V LDO, to be decoupled to GND with a 33nF ceramic capacitor close to the pin, supplying the USB transceiver and RSTOUT# and able to source up to 5mA to external 3.3V logic. |
| 7 | USBDP | bidirectional | USB data signal plus, requiring a 1.5k pull-up to 3V3OUT or RSTOUT#. |
| 8 | USBDM | bidirectional | USB data signal minus. |
| 9 | GND | power_in | Device ground supply pin. |
| 10 | SLEEP# | output | Goes low during USB suspend mode, typically used to power down an external TTL-to-RS232 level converter in USB to RS232 designs. |
| 11 | RXLED# | output | Open-collector LED driver that pulses low when receiving data over USB. |
| 12 | TXLED# | output | Open-collector LED driver that pulses low when transmitting data over USB. |
| 13 | VCCIO | power_in | +3.0V to +5.25V supply to the UART interface pins 10..12, 14..16 and 18..25, connected to the 3.3V supply of external logic or to VCC for 5V CMOS levels. |
| 14 | PWRCTL | input | Power control input: low for bus powered, high for self powered (to VCCIO). |
| 15 | PWREN# | output | Low after the device is configured over USB and high during USB suspend, usable to drive a P-channel logic-level MOSFET switch for external logic power, which requires the interface pull-down option enabled in the EEPROM. |
| 16 | TXDEN | output | Enables transmit data for RS485. |
| 17 | GND | power_in | Device ground supply pin. |
| 18 | RI# | input | Ring indicator control input that can be pulled low to resume the PC USB host controller when the remote wake-up option is enabled in the EEPROM. |
| 19 | DCD# | input | Data carrier detect control input. |
| 20 | DSR# | input | Data set ready control input / handshake signal. |
| 21 | DTR# | output | Data terminal ready control output / handshake signal. |
| 22 | CTS# | input | Clear to send control input / handshake signal. |
| 23 | RTS# | output | Request to send control output / handshake signal. |
| 24 | RXD | input | Receive asynchronous data input. |
| 25 | TXD | output | Transmit asynchronous data output. |
| 26 | VCC | power_in | +4.35V to +5.25V supply to the device core, LDO and non-UART interface pins. |
| 27 | XTIN | input | Input to the 6MHz crystal oscillator, which can also be driven by an external 6MHz clock whose switching threshold is VCC/2, so it must be driven at 5V CMOS level or AC coupled around VCC/2. |
| 28 | XTOUT | output | Output of the 6MHz crystal oscillator, which stops oscillating during USB suspend. |
| 29 | AGND | power_in | Analog ground for the internal x8 clock multiplier. |
| 30 | AVCC | power_in | Analog power supply for the internal x8 clock multiplier. |
| 31 | TEST | input | Puts the device into I.C. test mode and must be connected to GND for normal operation. |
| 32 | EECS | bidirectional | EEPROM chip select, pulled to GND with a 10K resistor for 48MHz operation and needing no resistor for 6MHz operation; tri-stated during device reset. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | JSMSEMI |
| Package | QFP-32(7x7) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 32 |
CAD (KiCad official)
- Symbol:
FT232BL-JSM - Footprint:
Package_QFP:LQFP-32_7x7mm_P0.8mm - 3D model: QFP-32(7x7) (KiCad packages3D, STEP)
- 3D model files:
ft232bl-jsm-etched.step/ft232bl-jsm-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ft232bl-jsm.step/ft232bl-jsm.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: JSMSEMI datasheet (20 pp, sha256
58ff7747de655db7, retrieved 2026-11-04, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(vision), consensusclaude-opus-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# FT232BL-JSM
**JSMSEMI** · USB ICs · QFP-32(7x7)
FT232BL-JSM from JSMSEMI, in a QFP-32(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EESK | output | Clock signal to the EEPROM, tri-stated during device reset and driven otherwise; a 10K pull-down on EESK makes the device use USB product ID 6004 (hex) instead of 6001. |
| 2 | EEDATA | bidirectional | EEPROM data I/O connected to the EEPROM data input directly and to its data output through a 2.2K resistor, with the EEPROM data output pulled up to VCC by 10K; tri-stated during device reset. |
| 3 | VCC | power_in | +4.35V to +5.25V supply to the device core, LDO and non-UART interface pins. |
| 4 | RESET# | input | Input that lets an external device reset the FT232BL; connect to VCC if not needed. |
| 5 | RSTOUT# | output | Internal reset generator output that stays high impedance for about 5ms after VCC exceeds 3.5V, then clamps to the 3.3V regulator output; also driven low when RESET# is low and unaffected by USB bus reset. |
| 6 | 3V3OUT | power_out | Output of the integrated 3.3V LDO, to be decoupled to GND with a 33nF ceramic capacitor close to the pin, supplying the USB transceiver and RSTOUT# and able to source up to 5mA to external 3.3V logic. |
| 7 | USBDP | bidirectional | USB data signal plus, requiring a 1.5k pull-up to 3V3OUT or RSTOUT#. |
| 8 | USBDM | bidirectional | USB data signal minus. |
| 9 | GND | power_in | Device ground supply pin. |
| 10 | SLEEP# | output | Goes low during USB suspend mode, typically used to power down an external TTL-to-RS232 level converter in USB to RS232 designs. |
| 11 | RXLED# | output | Open-collector LED driver that pulses low when receiving data over USB. |
| 12 | TXLED# | output | Open-collector LED driver that pulses low when transmitting data over USB. |
| 13 | VCCIO | power_in | +3.0V to +5.25V supply to the UART interface pins 10..12, 14..16 and 18..25, connected to the 3.3V supply of external logic or to VCC for 5V CMOS levels. |
| 14 | PWRCTL | input | Power control input: low for bus powered, high for self powered (to VCCIO). |
| 15 | PWREN# | output | Low after the device is configured over USB and high during USB suspend, usable to drive a P-channel logic-level MOSFET switch for external logic power, which requires the interface pull-down option enabled in the EEPROM. |
| 16 | TXDEN | output | Enables transmit data for RS485. |
| 17 | GND | power_in | Device ground supply pin. |
| 18 | RI# | input | Ring indicator control input that can be pulled low to resume the PC USB host controller when the remote wake-up option is enabled in the EEPROM. |
| 19 | DCD# | input | Data carrier detect control input. |
| 20 | DSR# | input | Data set ready control input / handshake signal. |
| 21 | DTR# | output | Data terminal ready control output / handshake signal. |
| 22 | CTS# | input | Clear to send control input / handshake signal. |
| 23 | RTS# | output | Request to send control output / handshake signal. |
| 24 | RXD | input | Receive asynchronous data input. |
| 25 | TXD | output | Transmit asynchronous data output. |
| 26 | VCC | power_in | +4.35V to +5.25V supply to the device core, LDO and non-UART interface pins. |
| 27 | XTIN | input | Input to the 6MHz crystal oscillator, which can also be driven by an external 6MHz clock whose switching threshold is VCC/2, so it must be driven at 5V CMOS level or AC coupled around VCC/2. |
| 28 | XTOUT | output | Output of the 6MHz crystal oscillator, which stops oscillating during USB suspend. |
| 29 | AGND | power_in | Analog ground for the internal x8 clock multiplier. |
| 30 | AVCC | power_in | Analog power supply for the internal x8 clock multiplier. |
| 31 | TEST | input | Puts the device into I.C. test mode and must be connected to GND for normal operation. |
| 32 | EECS | bidirectional | EEPROM chip select, pulled to GND with a 10K resistor for 48MHz operation and needing no resistor for 6MHz operation; tri-stated during device reset. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | JSMSEMI |
| Package | QFP-32(7x7) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 32 |
## CAD (KiCad official)
- Symbol: `FT232BL-JSM`
- Footprint: `Package_QFP:LQFP-32_7x7mm_P0.8mm`
- 3D model: QFP-32(7x7) (KiCad packages3D, STEP)
- 3D model files: `ft232bl-jsm-etched.step` / `ft232bl-jsm-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ft232bl-jsm.step` / `ft232bl-jsm.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [JSMSEMI datasheet](docs/ft232bl-jsm-datasheet.pdf) (20 pp, sha256 `58ff7747de655db7`, retrieved 2026-11-04, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (vision), consensus `claude-opus-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ft232bl-jsm-datasheet.pdf)