FM25Q04B-SO-T-G

{
 "schema": "adom.pads/1",
 "slug": "fm25q04b-so-t-g",
 "footprint": "SOIC-8_3.9x4.9mm_P1.27mm",
 "generated_from": {
  "footprint": "SOIC-8_3.9x4.9mm_P1.27mm@sha256:074ecb2092b24fa4",
  "pins": "page.json:component.pins",
  "overrides": null
 },
 "pin1": {
  "pad": "1",
  "at": [
   -2.475,
   -1.905
  ],
  "corner": "top-left",
  "source": "silk-marker",
  "derived_from": "SOIC-8_3.9x4.9mm_P1.27mm@sha256:074ecb2092b24fa4"
 },
 "pad_count": 8,
 "symbol_pins": [
  "1",
  "2",
  "3",
  "4",
  "5",
  "6",
  "7",
  "8"
 ],
 "paste_apertures": 0,
 "issues": [],
 "pads": [
  {
   "pad": "1",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "1",
   "name": "CS#",
   "type": "input",
   "description": "Active-low SPI Chip Select input. When high, device is deselected and DO/DQ pins are high-impedance; when low, device is enabled and instructions can be written / data read. Must track VCC at power-up; a pull-up resistor to VCC is recommended.",
   "is_pin1": true,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "2",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "2",
   "name": "DO/DQ1",
   "type": "bidirectional",
   "description": "Standard SPI Serial Data Output (DO); becomes bidirectional DQ1 in Dual SPI, Quad SPI, and QPI modes. Data is shifted out on the falling edge of CLK in Standard SPI mode.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "3",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "3",
   "name": "WP#/DQ2",
   "type": "bidirectional",
   "description": "Active-low Write Protect input for Standard/Dual SPI, used with the Status Register block-protect bits and SRP to hardware-protect part or all of the array. Becomes bidirectional DQ2 when the Quad Enable (QE) bit in Status Register-2 is set for Quad SPI / QPI operation.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "4",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    -2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "4",
   "name": "VSS",
   "type": "power_in",
   "description": "Device ground reference (0 V).",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "5",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "5",
   "name": "DI/DQ0",
   "type": "bidirectional",
   "description": "Standard SPI Serial Data Input (DI); becomes bidirectional DQ0 in Dual SPI, Quad SPI, and QPI modes. Instructions, addresses, and data are shifted in on the rising edge of CLK in Standard SPI mode.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "6",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "6",
   "name": "CLK",
   "type": "input",
   "description": "SPI Serial Clock input; provides timing for all serial input and output operations. Supports SPI Mode 0 and Mode 3, up to 100 MHz for FAST_READ and 50 MHz for standard READ.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "7",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -0.635
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "7",
   "name": "HOLD#/DQ3",
   "type": "bidirectional",
   "description": "Active-low Hold input for Standard/Dual SPI - when driven low with CS# low, pauses serial communication (DO becomes high-Z, DI/CLK ignored). Becomes bidirectional DQ3 when QE=1 for Quad SPI / QPI operation; HOLD# function is unavailable in Quad modes.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  },
  {
   "pad": "8",
   "kind": "smd",
   "shape": "roundrect",
   "at": [
    2.475,
    -1.905
   ],
   "rot": 0.0,
   "size": [
    1.95,
    0.6
   ],
   "layers": [
    "F.Cu",
    "F.Mask",
    "F.Paste"
   ],
   "thermal": false,
   "pin": "8",
   "name": "VCC",
   "type": "power_in",
   "description": "Positive supply voltage input, 2.3 V to 3.6 V single-supply operation. Decouple with a bypass capacitor close to the pin.",
   "is_pin1": false,
   "source": {
    "geometry": "SOIC-8_3.9x4.9mm_P1.27mm.kicad_mod",
    "meaning": "page.json:component.pins",
    "correspondence": "kicad: symbol pin number == pad name"
   }
  }
 ]
}