← Commit history

fm25l16b-gtr: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·ec8a82f0fa · ·parent 771d8c1
1 file changed +74−1
page.json+74−1
@@ -33,5 +33,78 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "FM25L16B-GTR",+    "manufacturer": "Infineon",+    "package": "SOIC-8",+    "pin_count": 8,+    "category": "FRAM",+    "parts": {+      "symbol": "fm25l16b-gtr.kicad_sym",+      "footprint": "fm25l16b-gtr.kicad_mod",+      "model_3d": "fm25l16b-gtr-etched.glb",+      "model_3d_plain": "fm25l16b-gtr.glb",+      "model_3d_step": "fm25l16b-gtr-etched.step",+      "model_3d_step_plain": "fm25l16b-gtr.step",+      "lbr": "fm25l16b-gtr.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "CS",+        "type": "input",+        "description": "Chip Select (active LOW). Activates the device and gates SCK internally; when HIGH, the device enters low-power standby mode, ignores other inputs, and tri-states SO. A falling edge on CS must occur before every opcode."+      },+      {+        "number": "2",+        "name": "SO",+        "type": "tri_state",+        "description": "Serial Output (MISO). Data output pin driven only during a read; tri-stated at all other times, including when HOLD is LOW. Data transitions occur on the falling edge of SCK."+      },+      {+        "number": "3",+        "name": "WP",+        "type": "input",+        "description": "Write Protect (active LOW). When WPEN = 1 in the Status Register, driving WP LOW inhibits writes to the Status Register (protecting the block-protect bits). Tie to VDD if unused."+      },+      {+        "number": "4",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground reference for the device. Must be connected to system ground."+      },+      {+        "number": "5",+        "name": "SI",+        "type": "input",+        "description": "Serial Input (MOSI). Data/command input, sampled on the rising edge of SCK and ignored otherwise. Should always be driven to a valid logic level to meet IDD specifications. SI may be tied to SO for a single-wire data interface."+      },+      {+        "number": "6",+        "name": "SCK",+        "type": "input",+        "description": "Serial Clock (0 to 20 MHz). All I/O is synchronized to SCK: inputs are latched on the rising edge and outputs are driven on the falling edge. Supports SPI modes 0 and 3."+      },+      {+        "number": "7",+        "name": "HOLD",+        "type": "input",+        "description": "HOLD (active LOW). Suspends the current serial operation when driven LOW while SCK is LOW; SCK and CS transitions are ignored during hold. All HOLD transitions must occur while SCK is LOW. Tie to VDD if unused."+      },+      {+        "number": "8",+        "name": "VDD",+        "type": "power_in",+        "description": "Power supply input, 2.7 V to 3.6 V (3.3 V typ). Typical standby current 3 uA; active current 0.2 mA at 1 MHz SCK, 3 mA at 20 MHz SCK."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}