component
FM2201D
Public Made by Adomby adom
Shenzhen Fuman Battery Management ICs, DFN-8(2x2). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
FM2201D
Shenzhen Fuman · Battery Management ICs · DFN-8(2x2)
FM2201D from Shenzhen Fuman, in a DFN-8(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | LX | output | Switching node of the internal P-MOS/N-MOS DC/DC converter, with an absolute maximum voltage of VBAT ±0.3 V. |
| 2 | GND | power_in | Ground reference pin for the device. |
| 3 | PROG | input | Charge current setting pin: a 1% resistor from PROG to GND sets the charge current (battery current is 800 times the PROG current), PROG input voltage limit is VP ±0.3 V, and leaving it floating gives 450 mA. |
| 4 | NC | unconnected | Not connected; floating with no internal bond wire. |
| 5 | VLED | output | Open-drain charge status indicator output that drives an external LED, with an input voltage limit of -0.3 to +6.0 V and a high-impedance state in DC/DC mode. |
| 6 | VP | power_in | Charger input and load connection pin, with a charger voltage range of 4.5 V to 5.5 V, an absolute maximum input of -0.3 to +6.0 V, and a 1.5 V regulated output in DC/DC mode. |
| 7 | NC | unconnected | Not connected; floating with no internal bond wire. |
| 8 | VBAT | power_in | Single-cell Li-ion battery connection, with a VBAT input voltage range of 2.8 V to 5.5 V and an absolute maximum of -0.3 to +6.0 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Shenzhen Fuman |
| Package | DFN-8(2x2) |
| Category | Power Management |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VBAT input voltage | VBAT | 2.8 | 5.5 | V | 3 | ||
| VP output voltage | Vout | 1.5 | V | 3 | |||
| VP supply voltage | VVP | 4.5 | 5.5 | V | 3 | ||
| Overdischarge protection voltage | VOD | 2.72 | 2.8 | 2.88 | V | VBAT falling | 3 |
| Overdischarge protection delay time | TOD | 80 | 100 | 120 | ms | VBAT=3.6V 2.0V | 3 |
| Full charge voltage | VREG | 4.158 | 4.2 | 4.242 | V | RPROG=10K, IVBAT=40mA | 3 |
| LX leakage current | ILKG | 1 | μA | VOUT=VLX=2.0V | 3 | ||
| LX leakage current | ILKG | -1 | μA | VBAT=2.0V, VLX=0 | 3 | ||
| VBAT battery current, charge end | IVBAT | -1 | μA | charge end, VBAT>VREG | 3 | ||
| VBAT battery current, shutdown | IVBAT | -1 | μA | shutdown mode (RPROG not connected), VBAT=1.5V~4.2V | 3 | ||
| Absolute maximum VBAT, VP, VLED input voltage | -0.3 | 6 | V | 2 | |||
| Storage temperature | -50 | 150 | ℃ | 2 | |||
| Operating junction temperature range | -40 | 150 | ℃ | 2 | |||
| HBM ESD rating | 4000 | V | HBM | 2 | |||
| MM ESD rating | 200 | V | MM | 2 | |||
| Maximum output current | IO_MAX | 2 | A | 3 | |||
| Efficiency | η | 91 | % | 3 | |||
| Quiescent operating current | IQ | 13 | μA | IVP=0mA | 3 | ||
| Current limit | ILIM | 2.5 | A | 3 | |||
| Switching frequency | fS | 1.2 | MHz | 3 | |||
| P-MOS on-resistance | R-PON | 0.12 | Ω | VBAT=3.6V, ILX=200mA | 3 | ||
| N-MOS on-resistance | R-NON | 0.12 | Ω | VBAT=3.6V, ILX=200mA | 3 | ||
| Soft-start time | TSS | 120 | us | 3 | |||
| Overdischarge operating current | ISLEEP | 30 | nA | VBAT=2.0V | 3 | ||
| Output short-circuit voltage threshold | VSHORT | 0.2 | V | 3 | |||
| Charger overvoltage protection threshold | VVP-OVH | 5.8 | V | 3 | |||
| Charger overvoltage recovery threshold | VVP-OVL | 5.5 | V | 3 | |||
| VP input voltage charge threshold, rising | VUVH | 3.8 | V | 3 | |||
| VP input voltage charge threshold, falling | VUVL | 3.6 | V | 3 | |||
| VP operating current, charging | IVP | 300 | μA | charging, RPROG=10K | 3 | ||
| VP operating current, charge end | IVP | 300 | μA | charge end, VBAT>VREG | 3 | ||
| Constant charge current | ICHG | 800 | mA | VBAT=3.6V, RPROG=1K | 3 | ||
| Constant charge current | ICHG | 450 | mA | VBAT=3.6V, RPROG floating | 3 | ||
| Trickle charge threshold voltage | VPREL | 2.8 | V | 4 | |||
| Precharge threshold voltage | VPREH | 3 | V | 3 | |||
| Output current setting voltage | VPROG | 1 | V | 4 | |||
| Output current setting factor | KSET | 800 | 4 | ||||
| VLED current-limit resistor | RVLED | 0 | Ω | 4 | |||
| Charge end delay time | TTERM | 2 | ms | 4 | |||
| PROG pull-up current | IPROG | 1 | μA | 4 | |||
| Regulator PMOS on-resistance | RON | 1 | Ω | IVBAT=100mA, VVP=4.2V | 4 | ||
| VVP-VBAT undervoltage lockout threshold, rising | VASDH | 100 | mV | VCC low to high | 4 | ||
| VVP-VBAT undervoltage lockout threshold, falling | VASDL | 30 | mV | VCC high to low | 4 | ||
| Overtemperature protection threshold | TOTP | 150 | ℃ | 4 | |||
| Overtemperature protection recovery hysteresis | TOTP-HYS | 40 | ℃ | 4 |
CAD (KiCad official)
- Symbol:
FM2201D - Footprint:
Package_DFN_QFN:DFN-8_2x2mm_P0.5mm - 3D model: DFN-8(2x2) (KiCad packages3D, STEP)
- 3D model files:
fm2201d-etched.step/fm2201d-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);fm2201d.step/fm2201d.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Shenzhen Fuman datasheet (7 pp, sha256
55b85d25d14b2bf1, retrieved 2026-11-02, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).