component
FM05PF
Public Made by Adomby adom
Shenzhen Fuman Battery Management, TSSOP-20. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
FM05PF
Shenzhen Fuman · Battery Management · TSSOP-20
FM05PF from Shenzhen Fuman, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DOIN | input | DO control terminal, used to control the discharge state through an external signal. |
| 2 | COIN | input | CO control terminal, used to control the charge state through an external signal. |
| 3 | TOV | passive | Connect a capacitor to set the overcharge detection delay, Tov = 10^7 x COV seconds (COV typically 0.1 μF). |
| 4 | TOVD | passive | Connect a capacitor to set the overdischarge detection delay, Tovd = 10^7 x COVD seconds (COVD typically 0.1 μF). |
| 5 | TOC1 | passive | Connect a capacitor to set the discharge overcurrent 1 detection delay, Toc1 = 2 x 10^6 x COC1 seconds. |
| 6 | TOC2 | passive | Connect a capacitor to set the discharge overcurrent 2 detection delay, Toc2 = 2 x 10^5 x COC2 seconds. |
| 7 | NTC | passive | Connect a negative temperature coefficient thermistor (typically 10 kΩ at 25 °C) for temperature detection. |
| 8 | TRH | passive | Connect a resistor to set the high-temperature protection threshold; RTRH = 2 x RNTC at the charge over-temperature point (typically 7 kΩ with a 103AT NTC). |
| 9 | VM | input | Overcurrent lock, charger and load detection terminal; an internal pull-down RVMS of 100 to 500 kΩ is switched in when overcurrent protection is active. |
| 10 | CO | output | Charge control MOS gate connection with high-level and high-impedance output; absolute maximum VCO is GND-20 V to VCC+0.3 V. |
| 11 | DO | output | Discharge control MOS gate connection with CMOS output; absolute maximum VDO is GND-0.3 V to VCC+0.3 V. |
| 12 | VIN | power_in | Discharge overcurrent and charge overcurrent detection terminal; thresholds are VOC1 0.10 V, VOC2 0.20 V, VSHORT 0.400 V and VOVCC -0.05 V. |
| 13 | SET | input | 4/5 cell application selection terminal. |
| 14 | GND | power_in | IC ground and connection to the negative terminal of battery 1. |
| 15 | VC1 | passive | Connection for the positive terminal of cell 1 and the negative terminal of cell 2. |
| 16 | VC2 | passive | Connection for the positive terminal of cell 2 and the negative terminal of cell 3. |
| 17 | VC3 | passive | Connection for the positive terminal of cell 3 and the negative terminal of cell 4. |
| 18 | VC4 | passive | Connection for the positive terminal of cell 4 and the negative terminal of cell 5. |
| 19 | VC5 | passive | Connection for the positive terminal of cell 5. |
| 20 | VCC | power_in | IC power supply and connection for the positive terminal of cell 5; the supply voltage range is 5 V to 30 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Shenzhen Fuman |
| Package | TSSOP-20 |
| Category | Power Management (PMIC) |
| Pins | 20 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 5 | 30 | V | 4 | ||
| Normal power consumption | IVCC | 25 | uA | V1=V2=V3=V4=V5=3.5V | 4 | ||
| Sleep (standby) power consumption | ISTB | 10 | uA | V1=V2=V3=V4=V5=2.0V | 4 | ||
| Overcharge detection threshold (tolerance about nominal VDET1) | VDET1 | -0.025 | 0.025 | V | V1=V2=V3=V4=3.5V; V5=3.5→4.4V | 4 | |
| Overcharge detection delay | TOV | 0.5 | 1 | 1.5 | s | V1=V2=V3=V4=3.5V; COV=0.1μF; V5=3.5→4.4V | 4 |
| Overcharge release threshold (tolerance about nominal VREL1) | VREL1 | -0.05 | 0.05 | V | V1=V2=V3=V4=3.5V; V5=4.4→3.5V | 4 | |
| Overcharge release delay | TREL1 | 10 | 20 | 30 | ms | V1=V2=V3=V4=3.5V; V5=4.4→3.5V | 4 |
| Temperature coefficient 1 | KU1 | -0.6 | 0 | 0.6 | mV/℃ | Ta= -40℃ to 85℃ | 4 |
| Overdischarge detection threshold (tolerance about nominal VDET2) | VDET2 | -0.08 | 0.08 | V | V1=V2=V3=V4=3.5V; V5=3.5→2.0V | 4 | |
| Overdischarge detection delay | TOVD | 0.5 | 1 | 1.5 | s | V1=V2=V3=V4=3.5V; COVD=0.1μF; V5=3.5→2.0V | 4 |
| Overdischarge release threshold (tolerance about nominal VREL2) | VREL2 | -0.1 | 0.1 | V | V1=V2=V3=V4=3.5V; V5=2.0→3.5V | 4 | |
| Overdischarge release delay | TREL2 | 10 | 20 | 30 | ms | V1=V2=V3=V4=3.5V; V5=2.0→3.5V | 4 |
| Discharge overcurrent 1 delay | TOC1 | 100 | 200 | 300 | ms | V1=V2=V3=V4=V5=3.5V; COC1=0.1μF; V6=0→0.12V | 4 |
| Discharge overcurrent 1 release delay | TROC1 | 100 | 200 | 300 | ms | V1=V2=V3=V4=V5=3.5V; V6=0→0.12V→0V | 4 |
| Overcurrent pull-down resistance | RVMS | 100 | 300 | 500 | kΩ | V1=V2=V3=V4=V5=3.5V; V6=0→0.12V | 4 |
| Temperature coefficient 2 | KU2 | -0.1 | 0 | 0.1 | mV/℃ | Ta= -40℃ to 85℃ | 4 |
| Discharge overcurrent 2 detection threshold (tolerance about nominal VOC2) | VOC2 | -20 | 20 | % | V1=V2=V3=V4=V5=3.5V; V6=0→0.5V | 4 | |
| Discharge overcurrent 2 delay | TOC2 | 10 | 20 | 30 | ms | V1=V2=V3=V4=V5=3.5V; COC2=0.1μF; V6=0→0.5V | 4 |
| Discharge overcurrent 2 release delay | TROC2 | 100 | 200 | 300 | ms | V1=V2=V3=V4=V5=3.5V; V6=0→0.5V→0V | 4 |
| Short-circuit detection threshold (tolerance about nominal VSHORT) | VSHORT | -20 | 20 | % | V1=V2=V3=V4=V5=3.5V; V6=0→1.2V | 4 | |
| Short-circuit detection delay | TSHORT | 100 | 300 | 600 | us | V1=V2=V3=V4=V5=3.5V; V6=0→1.2V→0V | 4 |
| Charge overcurrent detection threshold (tolerance about nominal VOVCC) | VOVCC | -0.03 | 0.03 | V | V1=V2=V3=V4=V5=3.5V; V6=0→-0.2V | 4 | |
| Charge overcurrent detection delay | TOVCC | 10 | 20 | 30 | ms | V1=V2=V3=V4=V5=3.5V; V6=0→-0.2V | 4 |
| CO output resistance (CO high) | RCO | 3 | 5 | 8 | KΩ | Normal state, CO is H (12V) | 4 |
| DO output resistance (DO high) | RDO | 3 | 5 | 8 | KΩ | Normal state, DO is H (12V) | 4 |
| DO output resistance (DO low) | RDO | 0.2 | 0.35 | 0.5 | Protection state, DO is L | 4 | |
| Supply voltage absolute maximum (VCC referenced to GND) | VCC | -0.3 | 30 | V | Referenced to GND | 3 | |
| Cell voltage Vcell1-Vcell5 absolute maximum | VCELL | -0.3 | 6 | V | Referenced to GND | 3 | |
| VM input terminal voltage absolute maximum | VM | -20 | 30 | V | Referenced to GND | 3 | |
| DO output terminal voltage absolute maximum | VDO | -0.3 | V | Min referenced to GND; max printed as VCC+0.3 V | 3 | ||
| CO output terminal voltage absolute maximum | VCO | -20 | V | Min referenced to GND; max printed as VCC+0.3 V | 3 | ||
| Operating ambient temperature | -40 | 85 | ℃ | 3 | |||
| Storage temperature | TSTG | -40 | 125 | ℃ | 3 | ||
| External resistor R1-R5 recommended value | R1-R5 | 100 | 1000 | 1000 | Ω | 10 | |
| External resistor RB1-RB5 recommended value | RB1-RB5 | 3 | 4.7 | 10 | MΩ | 10 | |
| External resistor RVCC recommended value | RVCC | 100 | 1000 | 1000 | Ω | 10 | |
| External resistor R6-R7 recommended value | R6-R7 | 0.2 | 0.5 | 0.8 | MΩ | 10 | |
| External resistor R8-R12 recommended value | R8-R12 | 10 | 47 | 200 | Ω | 10 | |
| External resistor RVM recommended value | RVM | 10 | 220 | 500 | kΩ | 10 | |
| External resistor RCO, RS recommended value | RCO, RS | 5 | 10 | 15 | MΩ | 10 | |
| External resistor RDO recommended value | RDO | 0 | 2 | 10 | kΩ | 10 | |
| External sense resistor Rsense recommended value | Rsense | 1 | 5 | 20 | mΩ | 10 | |
| External capacitor CVCC recommended value | CVCC | 10 | 10 | 100 | μF | 10 | |
| External capacitor C1-C5 recommended value | C1-C5 | 0.1 | 1 | 10 | μF | Withstand voltage >50V | 10 |
| NTC thermistor RNTC recommended value | RNTC | 10 | kΩ | 10 | |||
| TRH resistor RTRH recommended value | RTRH | 7 | kΩ | 10 | |||
| Delay capacitors COV, COVD, COC1, COC2 recommended value | COV, COVD, COC1, COC2 | 0.1 | μF | 10 |
CAD (KiCad official)
- Symbol:
FM05PF - Footprint:
Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm - 3D model: TSSOP-20 (KiCad packages3D, STEP)
- 3D model files:
fm05pf-etched.step/fm05pf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);fm05pf.step/fm05pf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Shenzhen Fuman datasheet (13 pp, sha256
83151fd4ac45b1a0, retrieved 2026-10-18, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# FM05PF
**Shenzhen Fuman** · Battery Management · TSSOP-20
FM05PF from Shenzhen Fuman, in a TSSOP-20. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DOIN | input | DO control terminal, used to control the discharge state through an external signal. |
| 2 | COIN | input | CO control terminal, used to control the charge state through an external signal. |
| 3 | TOV | passive | Connect a capacitor to set the overcharge detection delay, Tov = 10^7 x COV seconds (COV typically 0.1 μF). |
| 4 | TOVD | passive | Connect a capacitor to set the overdischarge detection delay, Tovd = 10^7 x COVD seconds (COVD typically 0.1 μF). |
| 5 | TOC1 | passive | Connect a capacitor to set the discharge overcurrent 1 detection delay, Toc1 = 2 x 10^6 x COC1 seconds. |
| 6 | TOC2 | passive | Connect a capacitor to set the discharge overcurrent 2 detection delay, Toc2 = 2 x 10^5 x COC2 seconds. |
| 7 | NTC | passive | Connect a negative temperature coefficient thermistor (typically 10 kΩ at 25 °C) for temperature detection. |
| 8 | TRH | passive | Connect a resistor to set the high-temperature protection threshold; RTRH = 2 x RNTC at the charge over-temperature point (typically 7 kΩ with a 103AT NTC). |
| 9 | VM | input | Overcurrent lock, charger and load detection terminal; an internal pull-down RVMS of 100 to 500 kΩ is switched in when overcurrent protection is active. |
| 10 | CO | output | Charge control MOS gate connection with high-level and high-impedance output; absolute maximum VCO is GND-20 V to VCC+0.3 V. |
| 11 | DO | output | Discharge control MOS gate connection with CMOS output; absolute maximum VDO is GND-0.3 V to VCC+0.3 V. |
| 12 | VIN | power_in | Discharge overcurrent and charge overcurrent detection terminal; thresholds are VOC1 0.10 V, VOC2 0.20 V, VSHORT 0.400 V and VOVCC -0.05 V. |
| 13 | SET | input | 4/5 cell application selection terminal. |
| 14 | GND | power_in | IC ground and connection to the negative terminal of battery 1. |
| 15 | VC1 | passive | Connection for the positive terminal of cell 1 and the negative terminal of cell 2. |
| 16 | VC2 | passive | Connection for the positive terminal of cell 2 and the negative terminal of cell 3. |
| 17 | VC3 | passive | Connection for the positive terminal of cell 3 and the negative terminal of cell 4. |
| 18 | VC4 | passive | Connection for the positive terminal of cell 4 and the negative terminal of cell 5. |
| 19 | VC5 | passive | Connection for the positive terminal of cell 5. |
| 20 | VCC | power_in | IC power supply and connection for the positive terminal of cell 5; the supply voltage range is 5 V to 30 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Shenzhen Fuman |
| Package | TSSOP-20 |
| Category | Power Management (PMIC) |
| Pins | 20 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 5 | | 30 | V | | 4 |
| Normal power consumption | IVCC | | | 25 | uA | V1=V2=V3=V4=V5=3.5V | 4 |
| Sleep (standby) power consumption | ISTB | | | 10 | uA | V1=V2=V3=V4=V5=2.0V | 4 |
| Overcharge detection threshold (tolerance about nominal VDET1) | VDET1 | -0.025 | | 0.025 | V | V1=V2=V3=V4=3.5V; V5=3.5→4.4V | 4 |
| Overcharge detection delay | TOV | 0.5 | 1 | 1.5 | s | V1=V2=V3=V4=3.5V; COV=0.1μF; V5=3.5→4.4V | 4 |
| Overcharge release threshold (tolerance about nominal VREL1) | VREL1 | -0.05 | | 0.05 | V | V1=V2=V3=V4=3.5V; V5=4.4→3.5V | 4 |
| Overcharge release delay | TREL1 | 10 | 20 | 30 | ms | V1=V2=V3=V4=3.5V; V5=4.4→3.5V | 4 |
| Temperature coefficient 1 | KU1 | -0.6 | 0 | 0.6 | mV/℃ | Ta= -40℃ to 85℃ | 4 |
| Overdischarge detection threshold (tolerance about nominal VDET2) | VDET2 | -0.08 | | 0.08 | V | V1=V2=V3=V4=3.5V; V5=3.5→2.0V | 4 |
| Overdischarge detection delay | TOVD | 0.5 | 1 | 1.5 | s | V1=V2=V3=V4=3.5V; COVD=0.1μF; V5=3.5→2.0V | 4 |
| Overdischarge release threshold (tolerance about nominal VREL2) | VREL2 | -0.1 | | 0.1 | V | V1=V2=V3=V4=3.5V; V5=2.0→3.5V | 4 |
| Overdischarge release delay | TREL2 | 10 | 20 | 30 | ms | V1=V2=V3=V4=3.5V; V5=2.0→3.5V | 4 |
| Discharge overcurrent 1 delay | TOC1 | 100 | 200 | 300 | ms | V1=V2=V3=V4=V5=3.5V; COC1=0.1μF; V6=0→0.12V | 4 |
| Discharge overcurrent 1 release delay | TROC1 | 100 | 200 | 300 | ms | V1=V2=V3=V4=V5=3.5V; V6=0→0.12V→0V | 4 |
| Overcurrent pull-down resistance | RVMS | 100 | 300 | 500 | kΩ | V1=V2=V3=V4=V5=3.5V; V6=0→0.12V | 4 |
| Temperature coefficient 2 | KU2 | -0.1 | 0 | 0.1 | mV/℃ | Ta= -40℃ to 85℃ | 4 |
| Discharge overcurrent 2 detection threshold (tolerance about nominal VOC2) | VOC2 | -20 | | 20 | % | V1=V2=V3=V4=V5=3.5V; V6=0→0.5V | 4 |
| Discharge overcurrent 2 delay | TOC2 | 10 | 20 | 30 | ms | V1=V2=V3=V4=V5=3.5V; COC2=0.1μF; V6=0→0.5V | 4 |
| Discharge overcurrent 2 release delay | TROC2 | 100 | 200 | 300 | ms | V1=V2=V3=V4=V5=3.5V; V6=0→0.5V→0V | 4 |
| Short-circuit detection threshold (tolerance about nominal VSHORT) | VSHORT | -20 | | 20 | % | V1=V2=V3=V4=V5=3.5V; V6=0→1.2V | 4 |
| Short-circuit detection delay | TSHORT | 100 | 300 | 600 | us | V1=V2=V3=V4=V5=3.5V; V6=0→1.2V→0V | 4 |
| Charge overcurrent detection threshold (tolerance about nominal VOVCC) | VOVCC | -0.03 | | 0.03 | V | V1=V2=V3=V4=V5=3.5V; V6=0→-0.2V | 4 |
| Charge overcurrent detection delay | TOVCC | 10 | 20 | 30 | ms | V1=V2=V3=V4=V5=3.5V; V6=0→-0.2V | 4 |
| CO output resistance (CO high) | RCO | 3 | 5 | 8 | KΩ | Normal state, CO is H (12V) | 4 |
| DO output resistance (DO high) | RDO | 3 | 5 | 8 | KΩ | Normal state, DO is H (12V) | 4 |
| DO output resistance (DO low) | RDO | 0.2 | 0.35 | 0.5 | | Protection state, DO is L | 4 |
| Supply voltage absolute maximum (VCC referenced to GND) | VCC | -0.3 | | 30 | V | Referenced to GND | 3 |
| Cell voltage Vcell1-Vcell5 absolute maximum | VCELL | -0.3 | | 6 | V | Referenced to GND | 3 |
| VM input terminal voltage absolute maximum | VM | -20 | | 30 | V | Referenced to GND | 3 |
| DO output terminal voltage absolute maximum | VDO | -0.3 | | | V | Min referenced to GND; max printed as VCC+0.3 V | 3 |
| CO output terminal voltage absolute maximum | VCO | -20 | | | V | Min referenced to GND; max printed as VCC+0.3 V | 3 |
| Operating ambient temperature | | -40 | | 85 | ℃ | | 3 |
| Storage temperature | TSTG | -40 | | 125 | ℃ | | 3 |
| External resistor R1-R5 recommended value | R1-R5 | 100 | 1000 | 1000 | Ω | | 10 |
| External resistor RB1-RB5 recommended value | RB1-RB5 | 3 | 4.7 | 10 | MΩ | | 10 |
| External resistor RVCC recommended value | RVCC | 100 | 1000 | 1000 | Ω | | 10 |
| External resistor R6-R7 recommended value | R6-R7 | 0.2 | 0.5 | 0.8 | MΩ | | 10 |
| External resistor R8-R12 recommended value | R8-R12 | 10 | 47 | 200 | Ω | | 10 |
| External resistor RVM recommended value | RVM | 10 | 220 | 500 | kΩ | | 10 |
| External resistor RCO, RS recommended value | RCO, RS | 5 | 10 | 15 | MΩ | | 10 |
| External resistor RDO recommended value | RDO | 0 | 2 | 10 | kΩ | | 10 |
| External sense resistor Rsense recommended value | Rsense | 1 | 5 | 20 | mΩ | | 10 |
| External capacitor CVCC recommended value | CVCC | 10 | 10 | 100 | μF | | 10 |
| External capacitor C1-C5 recommended value | C1-C5 | 0.1 | 1 | 10 | μF | Withstand voltage >50V | 10 |
| NTC thermistor RNTC recommended value | RNTC | | 10 | | kΩ | | 10 |
| TRH resistor RTRH recommended value | RTRH | | 7 | | kΩ | | 10 |
| Delay capacitors COV, COVD, COC1, COC2 recommended value | COV, COVD, COC1, COC2 | | 0.1 | | μF | | 10 |
## CAD (KiCad official)
- Symbol: `FM05PF`
- Footprint: `Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm`
- 3D model: TSSOP-20 (KiCad packages3D, STEP)
- 3D model files: `fm05pf-etched.step` / `fm05pf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `fm05pf.step` / `fm05pf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Shenzhen Fuman datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588946178109288448) (13 pp, sha256 `83151fd4ac45b1a0`, retrieved 2026-10-18, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/fm05pf-datasheet.pdf)