component
FH9261-G3JH
Public Made by Adomby adom
鑫飞宏 Battery Management, SOT-23-6. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownFH9261-G3JH
鑫飞宏 · Battery Management · SOT-23-6
FH9261-G3JH from 鑫飞宏, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DO | output | Drives the discharge-control MOSFET and goes low to turn it off on over-discharge (VOD 3.000 V), discharge overcurrent (VEC 0.080 V) or load short circuit (VSHORT 1.000 V); DO voltage is rated VSS-0.3 V to VDD+0.3 V. |
| 2 | VM | input | Current-sense input used for charge and discharge overcurrent, short-circuit and charger detection, rated VDD-12 V to VDD+0.3 V. |
| 3 | CO | output | Drives the charge-control MOSFET and goes low to turn it off on over-charge (VOC 4.280 V) or charge overcurrent (VCHA -0.100 V); CO voltage is rated VVM-0.3 V to VDD+0.3 V. |
| 4 | NC | unconnected | Listed as NC in Table 1; the datasheet gives no function or connection requirement for this pin. |
| 5 | VDD | power_in | Positive supply input for the IC, with chip supply voltage of 1.0 V to 7.5 V and an absolute maximum of VSS-0.3 V to VSS+8.0 V between VDD and VSS. |
| 6 | VSS | power_in | Ground reference for the IC; the battery voltage is measured between VDD and VSS and VM is referenced to VSS. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | 鑫飞宏 |
| Package | SOT-23-6 |
| Category | Power Management (PMIC) |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 芯片电源电压 (VDD to VSS input voltage, absolute maximum) | VDD | -0.3 | 8 | V | Printed as VSS-0.3 ~ VSS+8.0, referenced to VSS; Ta=+25°C unless noted | 3 | |
| VM input terminal voltage (absolute maximum) | VVM | -12 | 0.3 | V | Printed as VDD-12 ~ VDD+0.3, referenced to VDD | 3 | |
| CO output terminal voltage (absolute maximum) | VCO | -0.3 | 0.3 | V | Printed as VVM-0.3 ~ VDD+0.3; min referenced to VVM, max referenced to VDD | 3 | |
| DO output terminal voltage (absolute maximum) | VDO | -0.3 | 0.3 | V | Printed as VSS-0.3 ~ VDD+0.3; min referenced to VSS, max referenced to VDD | 3 | |
| 工作温度范围 (operating temperature range) | TOPR | -40 | 85 | °C | 3 | ||
| 储存温度范围 (storage temperature range) | TSTG | -55 | 125 | °C | 3 | ||
| 芯片电源电压 (chip supply voltage) | VDD | 1 | 7.5 | V | 4 | ||
| 正常工作电流 (normal operating current) | IVDD | 0.9 | 1.5 | 3 | μA | VDD=3.5V | 4 |
| 休眠电时消耗电流 (sleep current consumption) | IOPED | 0.1 | μA | VDD=1.5V | 4 | ||
| 过充电保护电压 (overcharge detection voltage) | VOC | 4.255 | 4.28 | 4.305 | V | VDD=3.5→4.8V | 4 |
| 过充电解除电压 (overcharge release voltage) | VOCR | 4.03 | 4.08 | 4.13 | V | VDD=4.8→3.5V | 4 |
| 过充电保护延时 (overcharge protection delay) | TOC | 500 | 1000 | 2000 | ms | VDD=3.5→4.8V | 4 |
| 过放电保护电压 (overdischarge detection voltage) | VOD | 2.92 | 3 | 3.08 | V | VC5=3.5→2.0V (as printed) | 4 |
| 过放电解除电压 (overdischarge release voltage) | VODR | 2.9 | 3 | 3.1 | V | VDD=2.0→3.5V | 4 |
| 过放电保护延时 (overdischarge protection delay) | TOD | 64 | 128 | 256 | ms | VDD=3.5→2.0V | 4 |
| 放电过流保护电压 (discharge overcurrent detection voltage) | VEC | 0.065 | 0.08 | 0.095 | V | VM-VSS=0→0.20V | 4 |
| 放电过流保护延时 (discharge overcurrent protection delay) | TEC | 4 | 8 | 16 | ms | VM-VSS=0→0.20V | 4 |
| 充电过流保护电压 (charge overcurrent detection voltage) | VCHA | -0.13 | -0.1 | -0.07 | V | VSS-VM=0→0.30V | 4 |
| 充电过流保护延时 (charge overcurrent protection delay) | TCHA | 4 | 8 | 16 | ms | VSS-VM=0→0.30V | 4 |
| 短路保护电压 (short-circuit detection voltage) | VSHORT | 0.7 | 1 | 1.3 | V | VM-VSS=0→1.5V | 4 |
| 短路保护延时 (short-circuit protection delay) | TSHORT | 125 | 250 | 500 | μs | VM-VSS=0→1.5V | 4 |
| 0V充电器起始电压 (0V charging starter voltage) | V0VCH | 0 | 0.7 | 1.5 | V | 0V battery charging function allowed | 4 |
CAD (KiCad official)
- Symbol:
FH9261-G3JH - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
fh9261-g3jh-etched.step/fh9261-g3jh-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);fh9261-g3jh.step/fh9261-g3jh.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: 鑫飞宏 datasheet (8 pp, sha256
bee8a057d6e94353, retrieved 2026-10-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).