component
FH7071GZ
Public Made by Adomby adom
鑫飞宏 Battery Management, SOT-23-6. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
FH7071GZ
鑫飞宏 · Battery Management · SOT-23-6
FH7071GZ from 鑫飞宏, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DO | output | Discharge MOSFET control terminal; DO inverts to switch off the discharge MOSFET on over-discharge, discharge over-current or short-circuit detection. |
| 2 | VM | input | Charge/discharge current detection terminal; VM must stay within VCC-12 V to VCC+0.3 V (absolute maximum), and the over-current thresholds are measured on this pin. |
| 3 | CO | output | Charge MOSFET control terminal; CO inverts to switch off the charge MOSFET on over-charge or charge over-current detection. |
| 4 | NC | unconnected | Not connected. |
| 5 | VCC | power_in | Power input connected to the positive terminal of the battery; the supply range is 1.0 V to 5.5 V (absolute maximum -0.3 V to 6 V). |
| 6 | VSS | power_in | Power ground connected to the negative terminal of the battery. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | 鑫飞宏 |
| Package | SOT-23-6 |
| Category | Power Management (PMIC) |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 芯片电源电压 (chip supply voltage) | VCC | 1 | 5.5 | V | 4 | ||
| 正常工作电流 (normal operating current) | IVCC | 0.9 | 1.5 | 3 | μA | VCC=3.5V | 4 |
| 过放电时消耗电流 (current consumption during over-discharge) | IOPED | 0.7 | 1.5 | μA | VCC =1.5V | 4 | |
| 充电器起始电压 (0V battery charging starting voltage, 允许向0V电池充电功能) | V0CH | 0 | 0.7 | 1.5 | V | 允许向 0V 电池充电功能 | 4 |
| 过充电保护电压 (overcharge detection voltage) | VOC | 4.4 | V | VCC =3.5→4.5V | 3 | ||
| 过充电解除电压 (overcharge release voltage) | VOCR | 4.2 | V | VCC =4.5→3.5V | 3 | ||
| 过放电保护电压 (overdischarge detection voltage) | VOD | 3 | V | VC5=3.5→2.0V | 3 | ||
| 过放电解除电压 (overdischarge release voltage) | VODR | 3 | V | VCC =2.0→3.5V | 3 | ||
| 放电过流保护电压 (discharge overcurrent detection voltage) | VEC | 0.18 | V | VM-VSS=0→0.20V | 3 | ||
| 充电过流保护电压 (charge overcurrent detection voltage) | VCHA | -0.15 | V | VSS-VM=0→0.30V | 3 | ||
| 短路保护电压 (short-circuit detection voltage) | VSHORT | 1 | V | VM -VSS=0→1.5V | 3 | ||
| 过充保护延时 (overcharge detection delay) | TOC | 1000 | ms | VCC =3.5→4.5V | 3 | ||
| 过放保护延时 (overdischarge detection delay) | TOD | 128 | ms | VCC =3.5→2.0V | 3 | ||
| 放电过流保护延时 (discharge overcurrent detection delay) | TEC | 8 | ms | VM-VSS=0→0.20V | 3 | ||
| 充电过流保护延时 (charge overcurrent detection delay) | TCHA | 8 | ms | VSS-VM=0→0.30V | 3 | ||
| 短路保护延时 (short-circuit detection delay) | TSHORT | 300 | μs | VM -VSS=0→1.5V | 3 | ||
| 电源电压 (supply voltage, absolute maximum) | VCC | -0.3 | 6 | V | 3 | ||
| 工作环境温度 (operating ambient temperature) | TOPR | -40 | 85 | °C | 3 | ||
| 保存温度 (storage temperature) | TSTG | -55 | 125 | °C | 3 | ||
| 外部电阻 R1 (application circuit, parameter range) | R1 | 470 | 470 | 1500 | Ω | 应用电路 图3 / 表6 参数范围 (datasheet notes values may change without notice) | 7 |
| 外部电容 C1 (application circuit, parameter range) | C1 | 0.1 | 0.1 | 1 | μF | 应用电路 图3 / 表6 参数范围 (datasheet notes values may change without notice) | 7 |
| 外部电阻 R2 (application circuit, parameter range) | R2 | 1000 | 2000 | 3000 | Ω | 应用电路 图3 / 表6 参数范围 (datasheet notes values may change without notice) | 7 |
CAD (KiCad official)
- Symbol:
FH7071GZ - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
fh7071gz-etched.step/fh7071gz-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);fh7071gz.step/fh7071gz.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: 鑫飞宏 datasheet (8 pp, sha256
574bd01cb7895cb2, retrieved 2026-10-25, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# FH7071GZ
**鑫飞宏** · Battery Management · SOT-23-6
FH7071GZ from 鑫飞宏, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DO | output | Discharge MOSFET control terminal; DO inverts to switch off the discharge MOSFET on over-discharge, discharge over-current or short-circuit detection. |
| 2 | VM | input | Charge/discharge current detection terminal; VM must stay within VCC-12 V to VCC+0.3 V (absolute maximum), and the over-current thresholds are measured on this pin. |
| 3 | CO | output | Charge MOSFET control terminal; CO inverts to switch off the charge MOSFET on over-charge or charge over-current detection. |
| 4 | NC | unconnected | Not connected. |
| 5 | VCC | power_in | Power input connected to the positive terminal of the battery; the supply range is 1.0 V to 5.5 V (absolute maximum -0.3 V to 6 V). |
| 6 | VSS | power_in | Power ground connected to the negative terminal of the battery. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | 鑫飞宏 |
| Package | SOT-23-6 |
| Category | Power Management (PMIC) |
| Pins | 6 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 芯片电源电压 (chip supply voltage) | VCC | 1 | | 5.5 | V | | 4 |
| 正常工作电流 (normal operating current) | IVCC | 0.9 | 1.5 | 3 | μA | VCC=3.5V | 4 |
| 过放电时消耗电流 (current consumption during over-discharge) | IOPED | | 0.7 | 1.5 | μA | VCC =1.5V | 4 |
| 充电器起始电压 (0V battery charging starting voltage, 允许向0V电池充电功能) | V0CH | 0 | 0.7 | 1.5 | V | 允许向 0V 电池充电功能 | 4 |
| 过充电保护电压 (overcharge detection voltage) | VOC | | 4.4 | | V | VCC =3.5→4.5V | 3 |
| 过充电解除电压 (overcharge release voltage) | VOCR | | 4.2 | | V | VCC =4.5→3.5V | 3 |
| 过放电保护电压 (overdischarge detection voltage) | VOD | | 3 | | V | VC5=3.5→2.0V | 3 |
| 过放电解除电压 (overdischarge release voltage) | VODR | | 3 | | V | VCC =2.0→3.5V | 3 |
| 放电过流保护电压 (discharge overcurrent detection voltage) | VEC | | 0.18 | | V | VM-VSS=0→0.20V | 3 |
| 充电过流保护电压 (charge overcurrent detection voltage) | VCHA | | -0.15 | | V | VSS-VM=0→0.30V | 3 |
| 短路保护电压 (short-circuit detection voltage) | VSHORT | | 1 | | V | VM -VSS=0→1.5V | 3 |
| 过充保护延时 (overcharge detection delay) | TOC | | 1000 | | ms | VCC =3.5→4.5V | 3 |
| 过放保护延时 (overdischarge detection delay) | TOD | | 128 | | ms | VCC =3.5→2.0V | 3 |
| 放电过流保护延时 (discharge overcurrent detection delay) | TEC | | 8 | | ms | VM-VSS=0→0.20V | 3 |
| 充电过流保护延时 (charge overcurrent detection delay) | TCHA | | 8 | | ms | VSS-VM=0→0.30V | 3 |
| 短路保护延时 (short-circuit detection delay) | TSHORT | | 300 | | μs | VM -VSS=0→1.5V | 3 |
| 电源电压 (supply voltage, absolute maximum) | VCC | -0.3 | | 6 | V | | 3 |
| 工作环境温度 (operating ambient temperature) | TOPR | -40 | | 85 | °C | | 3 |
| 保存温度 (storage temperature) | TSTG | -55 | | 125 | °C | | 3 |
| 外部电阻 R1 (application circuit, parameter range) | R1 | 470 | 470 | 1500 | Ω | 应用电路 图3 / 表6 参数范围 (datasheet notes values may change without notice) | 7 |
| 外部电容 C1 (application circuit, parameter range) | C1 | 0.1 | 0.1 | 1 | μF | 应用电路 图3 / 表6 参数范围 (datasheet notes values may change without notice) | 7 |
| 外部电阻 R2 (application circuit, parameter range) | R2 | 1000 | 2000 | 3000 | Ω | 应用电路 图3 / 表6 参数范围 (datasheet notes values may change without notice) | 7 |
## CAD (KiCad official)
- Symbol: `FH7071GZ`
- Footprint: `Package_TO_SOT_SMD:SOT-23-6`
- 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files: `fh7071gz-etched.step` / `fh7071gz-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `fh7071gz.step` / `fh7071gz.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [鑫飞宏 datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8603345525361942528) (8 pp, sha256 `574bd01cb7895cb2`, retrieved 2026-10-25, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/fh7071gz-datasheet.pdf)