component
F280049PZS
Public Made by Adomby adom
Texas Instruments Microcontrollers (MCU/MPU/SOC), LQFP-100(14x14). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
Generated by kicad-footprint-generator · KiCad file format 20260206
F280049PZS
Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-100(14x14)
F280049PZS from Texas Instruments, in a LQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO28 | bidirectional | General-purpose I/O 28 with mux options SCIA_RX, EPWM7_A, OUTPUTXBAR5, EQEP1_A, SD1_D3, EQEP2_STROBE, LINA_TX, SPIB_CLK and ERRORSTS. |
| 2 | XRSn | bidirectional | Device reset input and watchdog reset output (open-drain with internal pull-up); place 2.2kΩ to 10kΩ to VDDIO and at most 100nF to VSS. |
| 3 | VDDIO | power_in | 3.3V digital I/O supply pin; place at least 0.1µF decoupling on each pin. |
| 4 | VDD | power_in | 1.2V digital logic supply pin; about 20µF total decoupling near VDD pins is recommended. |
| 5 | VSS | power_in | Digital ground. |
| 6 | A6/PGA5_OF | bidirectional | ADC-A input 6 or PGA-5 output filter (optional), also CMPSS-5 inputs and AIO228. |
| 7 | B2/C6/PGA3_OF | bidirectional | ADC-B input 2, ADC-C input 6 or PGA-3 output filter (optional), also CMPSS-3 inputs and AIO226. |
| 8 | B3/VDAC | input | ADC-B input 3 or optional external reference for on-chip DAC; has a non-disableable 100pF capacitor to VSSA, and at least 1µF is needed when used as DAC reference. |
| 9 | A2/B6/PGA1_OF | bidirectional | ADC-A input 2, ADC-B input 6 or PGA-1 output filter (optional), also CMPSS-1 inputs and AIO224. |
| 10 | A3 | input | ADC-A input 3, also CMPSS-1 inputs and AIO233. |
| 11 | VDDA | power_in | 3.3V analog supply pin; place at least 2.2µF to VSSA on each pin. |
| 12 | VSSA | power_in | Analog ground. |
| 13 | PGA5_GND | input | PGA-5 ground reference; tie to VSSA if unused. |
| 14 | PGA1_GND | input | PGA-1 ground reference; tie to VSSA if unused. |
| 15 | PGA3_GND | input | PGA-3 ground reference; tie to VSSA if unused. |
| 16 | PGA5_IN | input | PGA-5 input, also CMPSS-5 positive inputs 2. |
| 17 | C4 | input | ADC-C input 4, also CMPSS-5 inputs and AIO239. |
| 18 | PGA1_IN | input | PGA-1 input, also CMPSS-1 positive inputs 2. |
| 19 | C0 | input | ADC-C input 0, also CMPSS-1 inputs and AIO237. |
| 20 | PGA3_IN | input | PGA-3 input, also CMPSS-3 positive inputs 2. |
| 21 | C2 | input | ADC-C input 2, also CMPSS-3 inputs and AIO244. |
| 22 | A1/DACB_OUT | bidirectional | ADC-A input 1 or buffered DAC-B output, also AIO232. |
| 23 | A0/B15/C15/DACA_OUT | bidirectional | ADC-A input 0, ADC-B input 15, ADC-C input 15 or buffered DAC-A output, also AIO231. |
| 24 | VREFHIB/VREFHIC | bidirectional | ADC-B and ADC-C high reference voltage; driven externally or by device, at least 2.2µF to the VREFLO pin, do not load externally. |
| 25 | VREFHIA | bidirectional | ADC-A high reference voltage; driven externally or by device, at least 2.2µF to VREFLOA, do not load externally. |
| 26 | VREFLOB/VREFLOC | input | ADC-B and ADC-C low reference voltage; tie to VSSA. |
| 27 | VREFLOA | input | ADC-A low reference voltage; tie to VSSA. |
| 28 | C5/PGA6_IN | input | ADC-C input 5 or PGA-6 input, also CMPSS-6 inputs and AIO240. |
| 29 | C1 | input | ADC-C input 1, also CMPSS-2 inputs and AIO238. |
| 30 | PGA2_IN | input | PGA-2 input, also CMPSS-2 positive inputs 2. |
| 31 | C3/PGA4_IN | input | ADC-C input 3 or PGA-4 input, also CMPSS-4 inputs and AIO245. |
| 32 | PGA2_GND/PGA4_GND/PGA6_GND | input | Shared ground reference for PGA-2, PGA-4 and PGA-6; tie to VSSA if unused. |
| 33 | VSSA | power_in | Analog ground. |
| 34 | VDDA | power_in | 3.3V analog supply pin; place at least 2.2µF to VSSA on each pin. |
| 35 | A5 | input | ADC-A input 5, also CMPSS-2 inputs and AIO234. |
| 36 | A4/B8/PGA2_OF | bidirectional | ADC-A input 4, ADC-B input 8 or PGA-2 output filter (optional), also CMPSS-2 inputs and AIO225. |
| 37 | A8/PGA6_OF | bidirectional | ADC-A input 8 or PGA-6 output filter (optional), also CMPSS-6 inputs and AIO229. |
| 38 | A9 | input | ADC-A input 9, also CMPSS-6 inputs and AIO236. |
| 39 | B4/C8/PGA4_OF | bidirectional | ADC-B input 4, ADC-C input 8 or PGA-4 output filter (optional), also CMPSS-4 inputs and AIO227. |
| 40 | A10/B1/C10/PGA7_OF | bidirectional | ADC-A input 10, ADC-B input 1, ADC-C input 10 or PGA-7 output filter (optional), also CMPSS-7 inputs and AIO230. |
| 41 | B0 | input | ADC-B input 0, also CMPSS-7 inputs and AIO241. |
| 42 | PGA7_GND | input | PGA-7 ground reference; tie to VSSA if unused. |
| 43 | PGA7_IN | input | PGA-7 input, also CMPSS-7 positive inputs 2. |
| 44 | C14 | input | ADC-C input 14, also CMPSS-7 inputs and AIO246. |
| 45 | VSS | power_in | Digital ground. |
| 46 | VDD | power_in | 1.2V digital logic supply pin; about 20µF total decoupling near VDD pins is recommended. |
| 47 | VDDIO | power_in | 3.3V digital I/O supply pin; place at least 0.1µF decoupling on each pin. |
| 48 | FLT2 | bidirectional | Flash test pin 2, reserved for TI; must be left unconnected. |
| 49 | FLT1 | bidirectional | Flash test pin 1, reserved for TI; must be left unconnected. |
| 50 | GPIO13 | bidirectional | General-purpose I/O 13 with mux options EPWM7_B, CANB_RX, EQEP1_INDEX, SCIB_RX, PMBUSA_ALERT and FSIRXA_CLK. |
| 51 | GPIO12 | bidirectional | General-purpose I/O 12 with mux options EPWM7_A, CANB_TX, EQEP1_STROBE, SCIB_TX, PMBUSA_CTL and FSIRXA_D0. |
| 52 | GPIO11 | bidirectional | General-purpose I/O 11 with mux options EPWM6_B, SCIB_RX, OUTPUTXBAR7, EQEP1_B, SPIA_STE and FSIRXA_D1. |
| 53 | GPIO33 | bidirectional | General-purpose I/O 33 with mux options I2CA_SCL, SPIB_STE, OUTPUTXBAR4, LINA_RX, SD1_C3, FSIRXA_CLK and CANA_RX. |
| 54 | GPIO16 | bidirectional | General-purpose I/O 16 with mux options SPIA_SIMO, CANB_TX, OUTPUTXBAR7, EPWM5_A, SCIA_TX, SD1_D1, XCLKOUT. |
| 55 | GPIO17 | bidirectional | General-purpose I/O 17 with mux options SPIA_SOMI, CANB_RX, OUTPUTXBAR8, EPWM5_B, SCIA_RX, SD1_C1, PMBUSA_SDA. |
| 56 | GPIO24 | bidirectional | General-purpose I/O 24 with mux options OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SD1_D1, PMBUSA_SCL, SCIA_TX and ERRORSTS. |
| 57 | GPIO25 | bidirectional | General-purpose I/O 25 with mux options OUTPUTXBAR2, EQEP2_B, SPIB_SOMI, SD1_C1, FSITXA_D1, PMBUSA_SDA, SCIA_RX. |
| 58 | GPIO26 | bidirectional | General-purpose I/O 26 with mux options OUTPUTXBAR3, EQEP2_INDEX, SPIB_CLK, SD1_D2, FSITXA_D0, PMBUSA_CTL, I2CA_SDA. |
| 59 | GPIO27 | bidirectional | General-purpose I/O 27 with mux options OUTPUTXBAR4, EQEP2_STROBE, SPIB_STE, SD1_C2, FSITXA_CLK, PMBUSA_ALERT, I2CA_SCL. |
| 60 | TCK | input | JTAG test clock with internal pull-up. |
| 61 | GPIO37/TDO | bidirectional | GPIO37 or JTAG TDO (default); tri-stated without JTAG activity so enable internal pull-up or add external pull-up. |
| 62 | TMS | bidirectional | JTAG test mode select with internal pull-up; add external pull-up (2.2kΩ recommended) to VDDIO. |
| 63 | GPIO35/TDI | bidirectional | GPIO35 or JTAG TDI (default); enable internal pull-up or add external pull-up to avoid floating input. |
| 64 | GPIO32 | bidirectional | General-purpose I/O 32 with mux options I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3, FSIRXA_D0, CANA_TX. |
| 65 | GPIO56 | bidirectional | General-purpose I/O 56 with mux options SPIA_CLK, EQEP2_STROBE, SCIB_TX, SD1_D3, SPIB_SIMO, EQEP1_A. |
| 66 | GPIO57 | bidirectional | General-purpose I/O 57 with mux options SPIA_STE, EQEP2_INDEX, SCIB_RX, SD1_C3, SPIB_SOMI, EQEP1_B. |
| 67 | GPIO58 | bidirectional | General-purpose I/O 58 with mux options OUTPUTXBAR1, SPIB_CLK, SD1_D4, LINA_TX, CANB_TX, EQEP1_STROBE. |
| 68 | GPIO18_X2 | bidirectional | GPIO18 or crystal oscillator output X2; GPIO use only when clocked by INTOSC with X1 having an external pull-down (1kΩ recommended). |
| 69 | X1 | bidirectional | Crystal oscillator or single-ended 3.3V clock input; tie to VSS if unused. |
| 70 | VDDIO | power_in | 3.3V digital I/O supply pin; place at least 0.1µF decoupling on each pin. |
| 71 | VDD | power_in | 1.2V digital logic supply pin; about 20µF total decoupling near VDD pins is recommended. |
| 72 | VSS | power_in | Digital ground. |
| 73 | VREGENZ | input | Internal regulator enable with internal pull-down; connect to VSS to enable internal VREG or to VDDIO to use external supply. |
| 74 | GPIO8 | bidirectional | General-purpose I/O 8 with mux options EPWM5_A, CANB_TX, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL, FSITXA_D1. |
| 75 | GPIO4 | bidirectional | General-purpose I/O 4 with mux options EPWM3_A, OUTPUTXBAR3, CANA_TX, FSIRXA_CLK. |
| 76 | GPIO3 | bidirectional | General-purpose I/O 3 with mux options EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX, FSIRXA_D0. |
| 77 | GPIO2 | bidirectional | General-purpose I/O 2 with mux options EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SCIA_TX, FSIRXA_D1. |
| 78 | GPIO1 | bidirectional | General-purpose I/O 1 with mux options EPWM1_B and I2CA_SCL. |
| 79 | GPIO0 | bidirectional | General-purpose I/O 0 with mux options EPWM1_A and I2CA_SDA. |
| 80 | VDDIO_SW | power_in | 3.3V supply for internal DC-DC regulator; needs 20µF bulk input capacitance when DC-DC is used and must connect to the VDDIO supply. |
| 81 | GPIO23_VSW | bidirectional | GPIO23 or DC-DC switch output VSW; default DC-DC mode, about 100pF internal capacitance. |
| 82 | VSS_SW | power_in | Internal DC-DC regulator ground; must connect to VSS. |
| 83 | GPIO22_VFBSW | bidirectional | GPIO22 or DC-DC feedback VFBSW; default DC-DC mode, connect to the node where L(VSW) meets the VDD rail when DC-DC is used. |
| 84 | GPIO7 | bidirectional | General-purpose I/O 7 with mux options EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO, FSITXA_CLK. |
| 85 | GPIO40 | bidirectional | General-purpose I/O 40 with mux options PMBUSA_SDA, FSIRXA_D0, SCIB_TX, EQEP1_A. |
| 86 | VSS | power_in | Digital ground. |
| 87 | VDD | power_in | 1.2V digital logic supply pin; about 20µF total decoupling near VDD pins is recommended. |
| 88 | VDDIO | power_in | 3.3V digital I/O supply pin; place at least 0.1µF decoupling on each pin. |
| 89 | GPIO5 | bidirectional | General-purpose I/O 5 with mux options EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE, FSITXA_D1. |
| 90 | GPIO9 | bidirectional | General-purpose I/O 9 with mux options EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX, SPIA_CLK, FSITXA_D0. |
| 91 | GPIO39 | bidirectional | General-purpose I/O 39 with mux options CANB_RX and FSIRXA_CLK. |
| 92 | GPIO59 | bidirectional | General-purpose I/O 59 with mux options OUTPUTXBAR2, SPIB_STE, SD1_C4, LINA_RX, CANB_RX, EQEP1_INDEX. |
| 93 | GPIO10 | bidirectional | General-purpose I/O 10 with mux options EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI, I2CA_SDA, FSITXA_CLK. |
| 94 | GPIO34 | bidirectional | General-purpose I/O 34 with mux options OUTPUTXBAR1 and PMBUSA_SDA. |
| 95 | GPIO15 | bidirectional | General-purpose I/O 15 with mux options EPWM8_B, SCIB_RX, OUTPUTXBAR4, PMBUSA_SCL, SPIB_STE, EQEP2_B. |
| 96 | GPIO14 | bidirectional | General-purpose I/O 14 with mux options EPWM8_A, SCIB_TX, OUTPUTXBAR3, PMBUSA_SDA, SPIB_CLK, EQEP2_A. |
| 97 | GPIO6 | bidirectional | General-purpose I/O 6 with mux options EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI, FSITXA_D0. |
| 98 | GPIO30 | bidirectional | General-purpose I/O 30 with mux options CANA_RX, SPIB_SIMO, OUTPUTXBAR7, EQEP1_STROBE, SD1_D4. |
| 99 | GPIO31 | bidirectional | General-purpose I/O 31 with mux options CANA_TX, SPIB_SOMI, OUTPUTXBAR8, EQEP1_INDEX, SD1_C4, FSIRXA_D1. |
| 100 | GPIO29 | bidirectional | General-purpose I/O 29 with mux options SCIA_TX, EPWM7_B, OUTPUTXBAR6, EQEP1_B, SD1_C3, EQEP2_INDEX, LINA_RX, SPIB_STE and ERRORSTS. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-100(14x14) |
| Category | Embedded Processors & Controllers |
| Pins | 100 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDDIO to VSS | VDDIO | -0.3 | 4.6 | V | referenced to VSS | 58 | |
| Supply voltage VDDA to VSSA | VDDA | -0.3 | 4.6 | V | referenced to VSSA | 58 | |
| Supply voltage VDD to VSS | VDD | -0.3 | 1.5 | V | referenced to VSS | 58 | |
| Voltage difference between VDDIO and VDDIO_SW pins | -0.3 | 0.3 | V | 58 | |||
| Input voltage (3.3V) | VIN | -0.3 | 4.6 | V | 3.3V | 58 | |
| Output voltage | VO | -0.3 | 4.6 | V | 58 | ||
| Digital input clamp current per pin | IIK | -20 | 20 | mA | VIN < VSS or VIN > VDDIO | 58 | |
| Analog input clamp current per pin | IIKANALOG | -20 | 20 | mA | VIN < VSSA or VIN > VDDA | 58 | |
| Total clamp current for all inputs | IIKTOTAL | -20 | 20 | mA | VIN < VSS/VSSA or VIN > VDDIO/VDDA | 58 | |
| Digital output current per pin | IOUT | -20 | 20 | mA | 58 | ||
| Natural ventilation temperature | TA | -40 | 125 | °C | 58 | ||
| Operating junction temperature | TJ | -40 | 150 | °C | 58 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 58 | ||
| Device supply voltage VDDIO and VDDA | 3.3 | 3.63 | V | internal BOR enabled; printed min is VBOR-VDDIO(MAX)+VBOR-GB | 59 | ||
| Device supply voltage VDDIO and VDDA | 2.8 | 3.3 | 3.63 | V | internal BOR disabled | 59 | |
| Device supply voltage VDD | VDD | 1.14 | 1.2 | 1.32 | V | 59 | |
| Junction temperature TJ (S version) | TJ | -40 | 125 | °C | S version | 59 | |
| Low-level output voltage VOL | VOL | 0.4 | V | IOL=IOL max | 67 | ||
| Low-level output voltage VOL | VOL | 0.2 | V | IOL = 100µA | 67 | ||
| High-level input voltage (3.3V) | VIH | 2 | V | 3.3V | 67 | ||
| Low-level input voltage (3.3V) | VIL | 0.8 | V | 3.3V | 67 | ||
| VDDIO undervoltage reset voltage | VBOR-VDDIO | 2.81 | 3 | V | 80 | ||
| Internal regulator output | VVREG | 1.14 | 1.2 | 1.32 | V | 80 | |
| Crystal load capacitance CL1, CL2 | CL1, CL2 | 12 | 24 | pF | 93 | ||
| Crystal shunt capacitance | C0 | 7 | pF | 93 | |||
| INTOSC frequency, INTOSC1 and INTOSC2 | fINTOSC | 9.7 | 10 | 10.3 | MHz | 94 | |
| Frequency stability | fINTOSC-STABILITY | -3 | 3 | % | frequency stability | 95 | |
| ADC external reference VREFHI - VREFLO | VREFHI - VREFLO | 2.4 | V | external reference; printed max is VDDA | 123 | ||
| ADC conversion range, internal reference 3.3V range | 0 | 3.3 | V | internal reference 3.3V range | 123 | ||
| ADC gain error, internal reference | -45 | 45 | LSB | internal reference voltage | 124 | ||
| ADC gain error, external reference | -5 | 3 | 5 | LSB | external reference | 124 | |
| ADC offset error | -5 | 2 | 5 | LSB | 124 | ||
| ADC DNL error | DNL | -1 | 0.5 | 1 | LSB | 124 | |
| ADC INL error | INL | -2 | 1 | 2 | LSB | 124 | |
| ADC clock ADCCLK (from PERx.SYSCLK) | ADCCLK | 5 | 50 | MHz | 123 | ||
| Buffered DAC offset error | -10 | 10 | mV | midpoint | 136 | ||
| Buffered DAC gain error | Gain | -2.5 | 2.5 | FSR 百分比 | 136 | ||
| Buffered DAC DNL | DNL | -1 | 0.4 | 1 | LSB | corrected endpoints | 136 |
| Buffered DAC INL | INL | -5 | 2 | 5 | LSB | corrected endpoints | 136 |
| Comparator input referred offset error | -20 | 20 | mV | low common mode, inverting input set to 50mV | 143 | ||
| CMPSS DAC static offset error | -25 | 25 | mV | 144 | |||
| CMPSS DAC static gain error | -2 | 2 | FSR 百分比 | 144 | |||
| CMPSS DAC static DNL | DNL | -1 | 4 | LSB | corrected endpoints | 144 | |
| CMPSS DAC static INL | INL | -16 | 16 | LSB | corrected endpoints | 144 | |
| CMPSS DAC output disturbance error | -100 | 100 | LSB | caused by comparator trip or DAC code change in same CMPSS module | 144 | ||
| PMBus low-level input voltage | VIL | 0.8 | V | 176 | |||
| PMBus high-level input voltage | VIH | 2.1 | V | printed max is VDDIO | 176 | ||
| PMBus low-level output voltage | VOL | 0.4 | V | Ipullup = 4mA | 176 | ||
| PMBus input leakage current per pin | Ii | -10 | 10 | µA | 0.1Vbus < Vi < 0.9Vbus | 176 | |
| PMBus SCL clock frequency, fast mode | fSCL | 10 | 400 | kHz | fast mode | 176 | |
| PMBus SCL clock frequency, standard mode | fSCL | 10 | 100 | kHz | standard mode | 177 | |
| Junction-to-ambient thermal resistance RΘJA (high-k PCB) | RΘJA | 46.1 | °C/W | 0 lfm | 68 | ||
| Junction-to-case thermal resistance RΘJC | RΘJC | 7.6 | °C/W | 68 | |||
| Junction-to-board thermal resistance RΘJB | RΘJB | 24.2 | °C/W | 68 | |||
| Junction-to-moving-air thermal resistance RΘJMA | RΘJMA | 37.3 | °C/W | 150 lfm | 68 | ||
| Junction-to-moving-air thermal resistance RΘJMA | RΘJMA | 34.8 | °C/W | 250 lfm | 68 | ||
| Junction-to-moving-air thermal resistance RΘJMA | RΘJMA | 32.6 | °C/W | 500 lfm | 68 |
CAD (KiCad official)
- Symbol:
F280049PZS - Footprint:
Package_QFP:LQFP-100_14x14mm_P0.5mm - 3D model: LQFP-100(14x14) (KiCad packages3D, STEP)
- 3D model files:
f280049pzs-etched.step/f280049pzs-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280049pzs.step/f280049pzs.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (277 pp, sha256
867e7bb5ada6819c, retrieved 2026-11-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-4-5-20251001(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).