component
F280049PZQ
Public Made by Adomby adom
Texas Instruments Pre-ordered MCUs, TQFP-100(14x14). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
7959248
F280049PZQ
Texas Instruments · Pre-ordered MCUs · TQFP-100(14x14)
F280049PZQ from Texas Instruments, in a TQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO28 | bidirectional | General-purpose I/O 28 with SCIA_RX, EPWM7_A, EQEP1_A, SD1_D3 and ERRORSTS alternate functions per the GPIO mux table. |
| 2 | XRSn | bidirectional | Device reset input and watchdog reset output; open-drain with internal pull-up, and an external 2.2kΩ to 10kΩ resistor to VDDIO is required. |
| 3 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF on each VDDIO pin. |
| 4 | VDD | power_in | 1.2V digital logic supply pin; place at least about 20µF total decoupling capacitance on the VDD pins. |
| 5 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 6 | A6/PGA5_OF | input | ADC-A input 6 (also PGA-5 output filter and CMPSS-5 comparator input); analog pin, not a digital I/O by default. |
| 7 | B2/C6/PGA3_OF | input | ADC-B input 2 (also ADC-C input 6 and PGA-3 output filter); analog pin. |
| 8 | B3/VDAC | input | ADC-B input 3 shared with the optional external DAC reference VDAC; a 100pF capacitor to VSSA is fixed on this pin and a 1µF capacitor is needed when used as the DAC reference. |
| 9 | A2/B6/PGA1_OF | input | ADC-A input 2 (also ADC-B input 6 and PGA-1 output filter); analog pin. |
| 10 | A3 | input | ADC-A input 3 with CMPSS-1 comparator inputs and a digital input AIO233. |
| 11 | VDDA | power_in | 3.3V analog supply pin; place a decoupling capacitor of at least 2.2µF to VSSA on each VDDA pin. |
| 12 | VSSA | power_in | Analog ground pin. |
| 13 | PGA5_GND | power_in | Kelvin ground reference for PGA-5 input. |
| 14 | PGA1_GND | power_in | Kelvin ground reference for PGA-1 input. |
| 15 | PGA3_GND | power_in | Kelvin ground reference for PGA-3 input. |
| 16 | PGA5_IN | input | Input to PGA-5, the programmable gain amplifier (gains 3, 6, 12, 24). |
| 17 | C4 | input | ADC-C input 4 with CMPSS-5 comparator inputs and digital input AIO239. |
| 18 | PGA1_IN | input | Input to PGA-1, the programmable gain amplifier (gains 3, 6, 12, 24). |
| 19 | C0 | input | ADC-C input 0 with CMPSS-1 comparator inputs and digital input AIO237. |
| 20 | PGA3_IN | input | Input to PGA-3, the programmable gain amplifier (gains 3, 6, 12, 24). |
| 21 | C2 | input | ADC-C input 2 with CMPSS-3 comparator inputs and digital input AIO244. |
| 22 | A1/DACB_OUT | input | ADC-A input 1, also buffered DAC-B output (output function when DAC enabled). |
| 23 | A0/B15/C15/DACA_OUT | input | ADC-A input 0 (also ADC-B 15, ADC-C 15) shared with buffered DAC-A output. |
| 24 | VREFHIB,VREFHIC | bidirectional | ADC-B and ADC-C high reference voltage; driven externally in external reference mode, and a 2.2µF capacitor is required on the pin. |
| 25 | VREFHIA | bidirectional | ADC-A high reference voltage; driven externally in external reference mode, and a 2.2µF capacitor is required on the pin. |
| 26 | VREFLOB,VREFLOC | input | ADC-B and ADC-C low reference voltage input. |
| 27 | VREFLOA | input | ADC-A low reference voltage input. |
| 28 | C5/PGA6_IN | input | ADC-C input 5 with CMPSS-6 comparator inputs, and input to PGA-6. |
| 29 | C1 | input | ADC-C input 1 with CMPSS-2 comparator inputs and digital input AIO238. |
| 30 | PGA2_IN | input | Input to PGA-2, the programmable gain amplifier (gains 3, 6, 12, 24). |
| 31 | C3/PGA4_IN | input | ADC-C input 3 with CMPSS-4 comparator inputs, also input to PGA-4. |
| 32 | PGA2_GND,PGA4_GND,PGA6_GND | power_in | Kelvin ground reference shared by PGA-2, PGA-4 and PGA-6. |
| 33 | VSSA | power_in | Analog ground pin. |
| 34 | VDDA | power_in | 3.3V analog supply pin; place a decoupling capacitor of at least 2.2µF to VSSA. |
| 35 | A5 | input | ADC-A input 5 with CMPSS-2 comparator inputs and digital input AIO234. |
| 36 | A4/B8/PGA2_OF | input | ADC-A input 4 (also ADC-B input 8 and PGA-2 output filter); analog pin. |
| 37 | A8/PGA6_OF | input | ADC-A input 8 with PGA-6 output filter and CMPSS-6 comparator input. |
| 38 | A9 | input | ADC-A input 9 with CMPSS-6 comparator inputs and digital input AIO236. |
| 39 | B4/C8/PGA4_OF | input | ADC-B input 4 (also ADC-C input 8 and PGA-4 output filter); analog pin. |
| 40 | A10/B1/C10/PGA7_OF | input | ADC-A input 10 (also ADC-B input 1 and ADC-C input 10) with PGA-7 output filter. |
| 41 | B0 | input | ADC-B input 0 with CMPSS-7 comparator inputs and digital input AIO241. |
| 42 | PGA7_GND | power_in | Kelvin ground reference for PGA-7 input. |
| 43 | PGA7_IN | input | Input to PGA-7, the programmable gain amplifier (gains 3, 6, 12, 24). |
| 44 | C14 | input | ADC-C input 14 with CMPSS-7 comparator inputs and digital input AIO246. |
| 45 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 46 | VDD | power_in | 1.2V digital logic supply pin; place decoupling capacitance on each VDD pin. |
| 47 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF. |
| 48 | FLT2 | bidirectional | Flash test pin 2 reserved for TI; must be left unconnected. |
| 49 | FLT1 | bidirectional | Flash test pin 1 reserved for TI; must be left unconnected. |
| 50 | GPIO13 | bidirectional | General-purpose I/O 13 with EPWM7_B, CANB_RX, EQEP1_INDEX, SCIB_RX and PMBUSA_ALERT alternate functions. |
| 51 | GPIO12 | bidirectional | General-purpose I/O 12 with EPWM7_A, CANB_TX, EQEP1_STROBE, SCIB_TX and PMBUSA_CTL alternate functions. |
| 52 | GPIO11 | bidirectional | General-purpose I/O 11 with EPWM6_B, SCIB_RX, EQEP1_B, SPIA_STE and FSIRXA_D1 alternate functions. |
| 53 | GPIO33 | bidirectional | General-purpose I/O 33 with I2CA_SCL, SPIB_STE, LINA_RX, SD1_C3 and CANA_RX alternate functions. |
| 54 | GPIO16 | bidirectional | General-purpose I/O 16 with SPIA_SIMO, CANB_TX, EPWM5_A, SD1_D1 and XCLKOUT alternate functions. |
| 55 | GPIO17 | bidirectional | General-purpose I/O 17 with SPIA_SOMI, CANB_RX, EPWM5_B, SD1_C1 and PMBUSA_SDA alternate functions. |
| 56 | GPIO24 | bidirectional | General-purpose I/O 24 with OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO and ERRORSTS alternate functions. |
| 57 | GPIO25 | bidirectional | General-purpose I/O 25 with OUTPUTXBAR2, EQEP2_B, SPIB_SOMI, SD1_C1 and SCIA_RX alternate functions. |
| 58 | GPIO26 | bidirectional | General-purpose I/O 26 with OUTPUTXBAR3, EQEP2_INDEX, SPIB_CLK, SD1_D2 and I2CA_SDA alternate functions. |
| 59 | GPIO27 | bidirectional | General-purpose I/O 27 with OUTPUTXBAR4, EQEP2_STROBE, SPIB_STE, SD1_C2 and I2CA_SCL alternate functions. |
| 60 | TCK | input | JTAG test clock input with internal pull-up enabled. |
| 61 | GPIO37/TDO | output | JTAG test data output TDO by default (tri-stated when JTAG is inactive); otherwise GPIO37 with OUTPUTXBAR2, I2CA_SCL and SCIA_TX alternate functions. |
| 62 | TMS | bidirectional | JTAG test mode select with internal pull-up; an external 2.2kΩ pull-up to VDDIO is recommended. |
| 63 | GPIO35/TDI | input | JTAG test data input TDI by default; otherwise GPIO35 with SCIA_RX, I2CA_SDA, CANA_RX and EQEP1_A alternate functions. |
| 64 | GPIO32 | bidirectional | General-purpose I/O 32 with I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3 and CANA_TX alternate functions. |
| 65 | GPIO56 | bidirectional | General-purpose I/O 56 with SPIA_CLK, EQEP2_STROBE, SCIB_TX, SD1_D3 and SPIB_SIMO alternate functions. |
| 66 | GPIO57 | bidirectional | General-purpose I/O 57 with SPIA_STE, EQEP2_INDEX, SCIB_RX, SD1_C3 and SPIB_SOMI alternate functions. |
| 67 | GPIO58 | bidirectional | General-purpose I/O 58 with OUTPUTXBAR1, SPIB_CLK, SD1_D4, LINA_TX and CANB_TX alternate functions. |
| 68 | GPIO18_X2 | bidirectional | General-purpose I/O 18 or crystal oscillator output X2; GPIO18 is usable only when the system is clocked by INTOSC and X1 has an external pull-down (recommended 1kΩ). |
| 69 | X1 | bidirectional | Crystal oscillator input or single-ended 3.3V clock input; the device initialization software must configure this pin before enabling the oscillator. |
| 70 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF. |
| 71 | VDD | power_in | 1.2V digital logic supply pin; place decoupling capacitance on each VDD pin. |
| 72 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 73 | VREGENZ | input | Internal regulator enable with internal pull-down; tie to VSS to enable the internal VREG or to VDDIO to use an external 1.2V supply. |
| 74 | GPIO8 | bidirectional | General-purpose I/O 8 with EPWM5_A, CANB_TX, ADCSOCAO, SCIA_TX, SPIA_SIMO and I2CA_SCL alternate functions. |
| 75 | GPIO4 | bidirectional | General-purpose I/O 4 with EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK alternate functions. |
| 76 | GPIO3 | bidirectional | General-purpose I/O 3 with EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and FSIRXA_D0 alternate functions. |
| 77 | GPIO2 | bidirectional | General-purpose I/O 2 with EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SCIA_TX and FSIRXA_D1 alternate functions. |
| 78 | GPIO1 | bidirectional | General-purpose I/O 1 with EPWM1_B and I2CA_SCL alternate functions; open-drain on the I2C function. |
| 79 | GPIO0 | bidirectional | General-purpose I/O 0 with EPWM1_A and I2CA_SDA alternate functions; open-drain on the I2C function. |
| 80 | VDDIO_SW | power_in | 3.3V supply for the internal DC/DC regulator; a 20µF bulk input capacitor is required and it must be tied to VDDIO. |
| 81 | GPIO23_VSW | bidirectional | General-purpose I/O 23 that defaults to the DC/DC switching node VSW when DCDCEN=1; internal capacitance is about 100pF. |
| 82 | VSS_SW | power_in | Internal DC/DC regulator ground; must be tied to the VSS pin. |
| 83 | GPIO22_VFBSW | bidirectional | General-purpose I/O 22 that defaults to the DC/DC feedback VFBSW; when the internal DC/DC is used, connect it to the node where L(VSW) connects to the VDD rail. |
| 84 | GPIO7 | bidirectional | General-purpose I/O 7 with EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK alternate functions. |
| 85 | GPIO40 | bidirectional | General-purpose I/O 40 with PMBUSA_SDA, FSIRXA_D0, SCIB_TX and EQEP1_A alternate functions. |
| 86 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 87 | VDD | power_in | 1.2V digital logic supply pin; place decoupling capacitance on each VDD pin. |
| 88 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF. |
| 89 | GPIO5 | bidirectional | General-purpose I/O 5 with EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1 alternate functions. |
| 90 | GPIO9 | bidirectional | General-purpose I/O 9 with EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX and SPIA_CLK alternate functions. |
| 91 | GPIO39 | bidirectional | General-purpose I/O 39 with CANB_RX and FSIRXA_CLK alternate functions. |
| 92 | GPIO59 | bidirectional | General-purpose I/O 59 with OUTPUTXBAR2, SPIB_STE, SD1_C4, LINA_RX, CANB_RX and EQEP1_INDEX alternate functions. |
| 93 | GPIO10 | bidirectional | General-purpose I/O 10 with EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI and I2CA_SDA alternate functions. |
| 94 | GPIO34 | bidirectional | General-purpose I/O 34 with OUTPUTXBAR1 and PMBUSA_SDA alternate functions. |
| 95 | GPIO15 | bidirectional | General-purpose I/O 15 with EPWM8_B, SCIB_RX, OUTPUTXBAR4, PMBUSA_SCL, SPIB_STE and EQEP2_B alternate functions. |
| 96 | GPIO14 | bidirectional | General-purpose I/O 14 with EPWM8_A, SCIB_TX, OUTPUTXBAR3, PMBUSA_SDA, SPIB_CLK and EQEP2_A alternate functions. |
| 97 | GPIO6 | bidirectional | General-purpose I/O 6 with EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0 alternate functions. |
| 98 | GPIO30 | bidirectional | General-purpose I/O 30 with CANA_RX, SPIB_SIMO, OUTPUTXBAR7, EQEP1_STROBE and SD1_D4 alternate functions. |
| 99 | GPIO31 | bidirectional | General-purpose I/O 31 with CANA_TX, SPIB_SOMI, OUTPUTXBAR8, EQEP1_INDEX, SD1_C4 and FSIRXA_D1 alternate functions. |
| 100 | GPIO29 | bidirectional | General-purpose I/O 29 with SCIA_TX, EPWM7_B, OUTPUTXBAR6, EQEP1_B, SD1_C3, LINA_RX and ERRORSTS alternate functions. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TQFP-100(14x14) |
| Category | Embedded Processors & Controllers |
| Pins | 100 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDDIO 电源电压 | VDDIO | -0.3 | 4.6 | V | 以 VSS 为基准 | 59 | |
| VDDA 电源电压 | VDDA | -0.3 | 4.6 | V | 以 VSSA 为基准 | 59 | |
| VDD 电源电压 | VDD | -0.3 | 1.5 | V | 以 VSS 为基准 | 59 | |
| 输入电压 (3.3V) | VIN | -0.3 | 4.6 | V | 59 | ||
| 输出电压 | VO | -0.3 | 4.6 | V | 59 | ||
| 数字输入钳位电流(每引脚) | IIK | -20 | 20 | mA | VIN < VSS 或 VIN > VDDIO | 59 | |
| 模拟输入钳位电流(每引脚) | IIKANALOG | -20 | 20 | mA | VIN < VSSA 或 VIN > VDDA | 59 | |
| 所有输入钳位电流总计 | IIKTOTAL | -20 | 20 | mA | VIN < VSS/VSSA 或 VIN > VDDIO/VDDA | 59 | |
| 数字输出电流(每引脚) | IOUT | -20 | 20 | mA | 59 | ||
| 自然通风温度 | TA | -40 | 125 | °C | 59 | ||
| 工作结温 | TJ | -40 | 150 | °C | 59 | ||
| 贮存温度 | Tstg | -65 | 150 | °C | 59 | ||
| 器件电源电压 VDDIO 和 VDDA | VDDIO | 3.3 | 3.63 | V | 启用内部 BOR | 60 | |
| 器件电源电压 VDDIO 和 VDDA | VDDIO | 2.8 | 3.3 | 3.63 | V | 禁用内部 BOR | 60 |
| 器件电源电压 VDD | VDD | 1.14 | 1.2 | 1.32 | V | 60 | |
| 结温 TJ(S 版本) | TJ | -40 | 125 | °C | S 版本 | 60 | |
| 自然通风温度 TA(Q 版本) | TA | -40 | 125 | °C | Q 版本(AEC Q100 认证) | 60 | |
| 高电平输入电压 (3.3V) | VIH | 2 | V | 68 | |||
| 低电平输入电压 (3.3V) | VIL | 0.8 | V | 68 | |||
| 输入迟滞 | VHYSTERESIS | 150 | mV | 68 | |||
| VDDIO 欠压复位电压 | VBOR-VDDIO | 2.81 | 3 | V | 68 | ||
| 运行模式 VDD 电流消耗 | IDD | 61 | 90 | mA | 运行模式 | 62 | |
| 运行模式 VDDIO 电流消耗 | IDDIO | 26 | 45 | mA | 运行模式 | 62 | |
| 运行模式 VDDA 电流消耗 | IDDA | 12 | 30 | mA | 运行模式 | 62 | |
| 空闲模式 VDD 电流消耗 | IDD | 18 | 40 | mA | 空闲模式 | 62 | |
| 空闲模式 VDDIO 电流消耗 | IDDIO | 1.2 | 4 | mA | 空闲模式 | 62 | |
| 空闲模式 VDDA 电流消耗 | IDDA | 0.9 | 1.2 | mA | 空闲模式 | 62 | |
| 停机模式 VDD 电流消耗 | IDD | 0.9 | 20 | mA | 停机模式 | 62 | |
| 停机模式 VDDIO 电流消耗 | IDDIO | 0.8 | 4 | mA | 停机模式 | 62 | |
| 停机模式 VDDA 电流消耗 | IDDA | 0.2 | 0.5 | mA | 停机模式 | 62 | |
| 闪存擦除/编程 VDD 电流消耗 | IDD | 40 | 70 | mA | 擦除/编程周期 | 62 | |
| 闪存擦除/编程 VDDIO 电流消耗 | IDDIO | 33 | 75 | mA | 擦除/编程周期 | 62 | |
| 闪存擦除/编程 VDDA 电流消耗 | IDDA | 0.1 | 2.5 | mA | 擦除/编程周期 | 62 | |
| 内部稳压器输出 | VVREG | 1.14 | 1.2 | 1.32 | V | 81 | |
| 内部振荡器频率 INTOSC1 和 INTOSC2 | fINTOSC | 9.7 | 10 | 10.3 | MHz | 95 | |
| 频率稳定性 | fINTOSC-STABILITY | -3 | 3 | % | 96 | ||
| ADCCLK(源自 PERx.SYSCLK) | 5 | 50 | MHz | 124 | |||
| VREFHI 外部基准 | VREFHI | 2.4 | V | 外部基准 | 124 | ||
| ADC 增益误差(内部基准电压) | -45 | 45 | LSB | 内部基准电压 | 125 | ||
| ADC 增益误差(外部基准) | -5 | 5 | LSB | 外部基准 | 125 | ||
| ADC 偏移量误差 | -5 | 5 | LSB | 125 | |||
| ADC DNL 误差 | -1 | 1 | LSB | 125 | |||
| ADC INL 误差 | -2 | 2 | LSB | 125 | |||
| 缓冲 DAC 有效输出电压范围 (RL=5kΩ) | VOUT | 0.3 | V | RL = 5kΩ | 137 | ||
| 缓冲 DAC 有效输出电压范围 (RL=1kΩ) | VOUT | 0.6 | V | RL = 1kΩ | 137 | ||
| 缓冲 DAC 增益误差 | -2.5 | 2.5 | FSR 百分比 | 138 | |||
| 缓冲 DAC DNL | -1 | 1 | LSB | 已更正端点 | 138 | ||
| 缓冲 DAC INL | -5 | 5 | LSB | 已更正端点 | 138 | ||
| 比较器以输入为基准的偏移量误差 | -20 | 20 | mV | 低共模,反相输入设置为 50mV | 144 | ||
| CMPSS DAC 静态偏移量误差 | -25 | 25 | mV | 145 | |||
| CMPSS DAC 静态增益误差 | -2 | 2 | FSR 百分比 | 145 | |||
| CMPSS DAC 静态 DNL | -1 | 4 | LSB | 已更正端点 | 145 | ||
| CMPSS DAC 静态 INL | -16 | 16 | LSB | 已更正端点 | 145 | ||
| SCL 时钟频率(PMBus 快速模式) | fSCL | 10 | 400 | kHz | 快速模式 | 177 | |
| SCL 时钟频率(PMBus 标准模式) | fSCL | 10 | 100 | kHz | 标准模式 | 178 | |
| 结至外壳热阻 | RΘJC | 7.6 | °C/W | PZ 封装 | 69 | ||
| 结至电路板热阻 | RΘJB | 24.2 | °C/W | PZ 封装 | 69 | ||
| 结至大气热阻(高 k PCB) | RΘJA | 46.1 | °C/W | 高 k PCB,0 lfm,PZ 封装 | 69 |
CAD (KiCad official)
- Symbol:
F280049PZQ - Footprint:
Package_QFP:TQFP-100_14x14mm_P0.5mm - 3D model: TQFP-100(14x14) (KiCad packages3D, STEP)
- 3D model files:
f280049pzq-etched.step/f280049pzq-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280049pzq.step/f280049pzq.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (270 pp, sha256
f0eccdafc7ec75fa, retrieved 2026-11-02, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# F280049PZQ
**Texas Instruments** · Pre-ordered MCUs · TQFP-100(14x14)
F280049PZQ from Texas Instruments, in a TQFP-100(14x14). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO28 | bidirectional | General-purpose I/O 28 with SCIA_RX, EPWM7_A, EQEP1_A, SD1_D3 and ERRORSTS alternate functions per the GPIO mux table. |
| 2 | XRSn | bidirectional | Device reset input and watchdog reset output; open-drain with internal pull-up, and an external 2.2kΩ to 10kΩ resistor to VDDIO is required. |
| 3 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF on each VDDIO pin. |
| 4 | VDD | power_in | 1.2V digital logic supply pin; place at least about 20µF total decoupling capacitance on the VDD pins. |
| 5 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 6 | A6/PGA5_OF | input | ADC-A input 6 (also PGA-5 output filter and CMPSS-5 comparator input); analog pin, not a digital I/O by default. |
| 7 | B2/C6/PGA3_OF | input | ADC-B input 2 (also ADC-C input 6 and PGA-3 output filter); analog pin. |
| 8 | B3/VDAC | input | ADC-B input 3 shared with the optional external DAC reference VDAC; a 100pF capacitor to VSSA is fixed on this pin and a 1µF capacitor is needed when used as the DAC reference. |
| 9 | A2/B6/PGA1_OF | input | ADC-A input 2 (also ADC-B input 6 and PGA-1 output filter); analog pin. |
| 10 | A3 | input | ADC-A input 3 with CMPSS-1 comparator inputs and a digital input AIO233. |
| 11 | VDDA | power_in | 3.3V analog supply pin; place a decoupling capacitor of at least 2.2µF to VSSA on each VDDA pin. |
| 12 | VSSA | power_in | Analog ground pin. |
| 13 | PGA5_GND | power_in | Kelvin ground reference for PGA-5 input. |
| 14 | PGA1_GND | power_in | Kelvin ground reference for PGA-1 input. |
| 15 | PGA3_GND | power_in | Kelvin ground reference for PGA-3 input. |
| 16 | PGA5_IN | input | Input to PGA-5, the programmable gain amplifier (gains 3, 6, 12, 24). |
| 17 | C4 | input | ADC-C input 4 with CMPSS-5 comparator inputs and digital input AIO239. |
| 18 | PGA1_IN | input | Input to PGA-1, the programmable gain amplifier (gains 3, 6, 12, 24). |
| 19 | C0 | input | ADC-C input 0 with CMPSS-1 comparator inputs and digital input AIO237. |
| 20 | PGA3_IN | input | Input to PGA-3, the programmable gain amplifier (gains 3, 6, 12, 24). |
| 21 | C2 | input | ADC-C input 2 with CMPSS-3 comparator inputs and digital input AIO244. |
| 22 | A1/DACB_OUT | input | ADC-A input 1, also buffered DAC-B output (output function when DAC enabled). |
| 23 | A0/B15/C15/DACA_OUT | input | ADC-A input 0 (also ADC-B 15, ADC-C 15) shared with buffered DAC-A output. |
| 24 | VREFHIB,VREFHIC | bidirectional | ADC-B and ADC-C high reference voltage; driven externally in external reference mode, and a 2.2µF capacitor is required on the pin. |
| 25 | VREFHIA | bidirectional | ADC-A high reference voltage; driven externally in external reference mode, and a 2.2µF capacitor is required on the pin. |
| 26 | VREFLOB,VREFLOC | input | ADC-B and ADC-C low reference voltage input. |
| 27 | VREFLOA | input | ADC-A low reference voltage input. |
| 28 | C5/PGA6_IN | input | ADC-C input 5 with CMPSS-6 comparator inputs, and input to PGA-6. |
| 29 | C1 | input | ADC-C input 1 with CMPSS-2 comparator inputs and digital input AIO238. |
| 30 | PGA2_IN | input | Input to PGA-2, the programmable gain amplifier (gains 3, 6, 12, 24). |
| 31 | C3/PGA4_IN | input | ADC-C input 3 with CMPSS-4 comparator inputs, also input to PGA-4. |
| 32 | PGA2_GND,PGA4_GND,PGA6_GND | power_in | Kelvin ground reference shared by PGA-2, PGA-4 and PGA-6. |
| 33 | VSSA | power_in | Analog ground pin. |
| 34 | VDDA | power_in | 3.3V analog supply pin; place a decoupling capacitor of at least 2.2µF to VSSA. |
| 35 | A5 | input | ADC-A input 5 with CMPSS-2 comparator inputs and digital input AIO234. |
| 36 | A4/B8/PGA2_OF | input | ADC-A input 4 (also ADC-B input 8 and PGA-2 output filter); analog pin. |
| 37 | A8/PGA6_OF | input | ADC-A input 8 with PGA-6 output filter and CMPSS-6 comparator input. |
| 38 | A9 | input | ADC-A input 9 with CMPSS-6 comparator inputs and digital input AIO236. |
| 39 | B4/C8/PGA4_OF | input | ADC-B input 4 (also ADC-C input 8 and PGA-4 output filter); analog pin. |
| 40 | A10/B1/C10/PGA7_OF | input | ADC-A input 10 (also ADC-B input 1 and ADC-C input 10) with PGA-7 output filter. |
| 41 | B0 | input | ADC-B input 0 with CMPSS-7 comparator inputs and digital input AIO241. |
| 42 | PGA7_GND | power_in | Kelvin ground reference for PGA-7 input. |
| 43 | PGA7_IN | input | Input to PGA-7, the programmable gain amplifier (gains 3, 6, 12, 24). |
| 44 | C14 | input | ADC-C input 14 with CMPSS-7 comparator inputs and digital input AIO246. |
| 45 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 46 | VDD | power_in | 1.2V digital logic supply pin; place decoupling capacitance on each VDD pin. |
| 47 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF. |
| 48 | FLT2 | bidirectional | Flash test pin 2 reserved for TI; must be left unconnected. |
| 49 | FLT1 | bidirectional | Flash test pin 1 reserved for TI; must be left unconnected. |
| 50 | GPIO13 | bidirectional | General-purpose I/O 13 with EPWM7_B, CANB_RX, EQEP1_INDEX, SCIB_RX and PMBUSA_ALERT alternate functions. |
| 51 | GPIO12 | bidirectional | General-purpose I/O 12 with EPWM7_A, CANB_TX, EQEP1_STROBE, SCIB_TX and PMBUSA_CTL alternate functions. |
| 52 | GPIO11 | bidirectional | General-purpose I/O 11 with EPWM6_B, SCIB_RX, EQEP1_B, SPIA_STE and FSIRXA_D1 alternate functions. |
| 53 | GPIO33 | bidirectional | General-purpose I/O 33 with I2CA_SCL, SPIB_STE, LINA_RX, SD1_C3 and CANA_RX alternate functions. |
| 54 | GPIO16 | bidirectional | General-purpose I/O 16 with SPIA_SIMO, CANB_TX, EPWM5_A, SD1_D1 and XCLKOUT alternate functions. |
| 55 | GPIO17 | bidirectional | General-purpose I/O 17 with SPIA_SOMI, CANB_RX, EPWM5_B, SD1_C1 and PMBUSA_SDA alternate functions. |
| 56 | GPIO24 | bidirectional | General-purpose I/O 24 with OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO and ERRORSTS alternate functions. |
| 57 | GPIO25 | bidirectional | General-purpose I/O 25 with OUTPUTXBAR2, EQEP2_B, SPIB_SOMI, SD1_C1 and SCIA_RX alternate functions. |
| 58 | GPIO26 | bidirectional | General-purpose I/O 26 with OUTPUTXBAR3, EQEP2_INDEX, SPIB_CLK, SD1_D2 and I2CA_SDA alternate functions. |
| 59 | GPIO27 | bidirectional | General-purpose I/O 27 with OUTPUTXBAR4, EQEP2_STROBE, SPIB_STE, SD1_C2 and I2CA_SCL alternate functions. |
| 60 | TCK | input | JTAG test clock input with internal pull-up enabled. |
| 61 | GPIO37/TDO | output | JTAG test data output TDO by default (tri-stated when JTAG is inactive); otherwise GPIO37 with OUTPUTXBAR2, I2CA_SCL and SCIA_TX alternate functions. |
| 62 | TMS | bidirectional | JTAG test mode select with internal pull-up; an external 2.2kΩ pull-up to VDDIO is recommended. |
| 63 | GPIO35/TDI | input | JTAG test data input TDI by default; otherwise GPIO35 with SCIA_RX, I2CA_SDA, CANA_RX and EQEP1_A alternate functions. |
| 64 | GPIO32 | bidirectional | General-purpose I/O 32 with I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3 and CANA_TX alternate functions. |
| 65 | GPIO56 | bidirectional | General-purpose I/O 56 with SPIA_CLK, EQEP2_STROBE, SCIB_TX, SD1_D3 and SPIB_SIMO alternate functions. |
| 66 | GPIO57 | bidirectional | General-purpose I/O 57 with SPIA_STE, EQEP2_INDEX, SCIB_RX, SD1_C3 and SPIB_SOMI alternate functions. |
| 67 | GPIO58 | bidirectional | General-purpose I/O 58 with OUTPUTXBAR1, SPIB_CLK, SD1_D4, LINA_TX and CANB_TX alternate functions. |
| 68 | GPIO18_X2 | bidirectional | General-purpose I/O 18 or crystal oscillator output X2; GPIO18 is usable only when the system is clocked by INTOSC and X1 has an external pull-down (recommended 1kΩ). |
| 69 | X1 | bidirectional | Crystal oscillator input or single-ended 3.3V clock input; the device initialization software must configure this pin before enabling the oscillator. |
| 70 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF. |
| 71 | VDD | power_in | 1.2V digital logic supply pin; place decoupling capacitance on each VDD pin. |
| 72 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 73 | VREGENZ | input | Internal regulator enable with internal pull-down; tie to VSS to enable the internal VREG or to VDDIO to use an external 1.2V supply. |
| 74 | GPIO8 | bidirectional | General-purpose I/O 8 with EPWM5_A, CANB_TX, ADCSOCAO, SCIA_TX, SPIA_SIMO and I2CA_SCL alternate functions. |
| 75 | GPIO4 | bidirectional | General-purpose I/O 4 with EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK alternate functions. |
| 76 | GPIO3 | bidirectional | General-purpose I/O 3 with EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and FSIRXA_D0 alternate functions. |
| 77 | GPIO2 | bidirectional | General-purpose I/O 2 with EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SCIA_TX and FSIRXA_D1 alternate functions. |
| 78 | GPIO1 | bidirectional | General-purpose I/O 1 with EPWM1_B and I2CA_SCL alternate functions; open-drain on the I2C function. |
| 79 | GPIO0 | bidirectional | General-purpose I/O 0 with EPWM1_A and I2CA_SDA alternate functions; open-drain on the I2C function. |
| 80 | VDDIO_SW | power_in | 3.3V supply for the internal DC/DC regulator; a 20µF bulk input capacitor is required and it must be tied to VDDIO. |
| 81 | GPIO23_VSW | bidirectional | General-purpose I/O 23 that defaults to the DC/DC switching node VSW when DCDCEN=1; internal capacitance is about 100pF. |
| 82 | VSS_SW | power_in | Internal DC/DC regulator ground; must be tied to the VSS pin. |
| 83 | GPIO22_VFBSW | bidirectional | General-purpose I/O 22 that defaults to the DC/DC feedback VFBSW; when the internal DC/DC is used, connect it to the node where L(VSW) connects to the VDD rail. |
| 84 | GPIO7 | bidirectional | General-purpose I/O 7 with EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK alternate functions. |
| 85 | GPIO40 | bidirectional | General-purpose I/O 40 with PMBUSA_SDA, FSIRXA_D0, SCIB_TX and EQEP1_A alternate functions. |
| 86 | VSS | power_in | Digital ground pin that must be connected to the board ground. |
| 87 | VDD | power_in | 1.2V digital logic supply pin; place decoupling capacitance on each VDD pin. |
| 88 | VDDIO | power_in | 3.3V digital I/O supply pin; place a decoupling capacitor of at least 0.1µF. |
| 89 | GPIO5 | bidirectional | General-purpose I/O 5 with EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1 alternate functions. |
| 90 | GPIO9 | bidirectional | General-purpose I/O 9 with EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX and SPIA_CLK alternate functions. |
| 91 | GPIO39 | bidirectional | General-purpose I/O 39 with CANB_RX and FSIRXA_CLK alternate functions. |
| 92 | GPIO59 | bidirectional | General-purpose I/O 59 with OUTPUTXBAR2, SPIB_STE, SD1_C4, LINA_RX, CANB_RX and EQEP1_INDEX alternate functions. |
| 93 | GPIO10 | bidirectional | General-purpose I/O 10 with EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI and I2CA_SDA alternate functions. |
| 94 | GPIO34 | bidirectional | General-purpose I/O 34 with OUTPUTXBAR1 and PMBUSA_SDA alternate functions. |
| 95 | GPIO15 | bidirectional | General-purpose I/O 15 with EPWM8_B, SCIB_RX, OUTPUTXBAR4, PMBUSA_SCL, SPIB_STE and EQEP2_B alternate functions. |
| 96 | GPIO14 | bidirectional | General-purpose I/O 14 with EPWM8_A, SCIB_TX, OUTPUTXBAR3, PMBUSA_SDA, SPIB_CLK and EQEP2_A alternate functions. |
| 97 | GPIO6 | bidirectional | General-purpose I/O 6 with EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0 alternate functions. |
| 98 | GPIO30 | bidirectional | General-purpose I/O 30 with CANA_RX, SPIB_SIMO, OUTPUTXBAR7, EQEP1_STROBE and SD1_D4 alternate functions. |
| 99 | GPIO31 | bidirectional | General-purpose I/O 31 with CANA_TX, SPIB_SOMI, OUTPUTXBAR8, EQEP1_INDEX, SD1_C4 and FSIRXA_D1 alternate functions. |
| 100 | GPIO29 | bidirectional | General-purpose I/O 29 with SCIA_TX, EPWM7_B, OUTPUTXBAR6, EQEP1_B, SD1_C3, LINA_RX and ERRORSTS alternate functions. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TQFP-100(14x14) |
| Category | Embedded Processors & Controllers |
| Pins | 100 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDDIO 电源电压 | VDDIO | -0.3 | | 4.6 | V | 以 VSS 为基准 | 59 |
| VDDA 电源电压 | VDDA | -0.3 | | 4.6 | V | 以 VSSA 为基准 | 59 |
| VDD 电源电压 | VDD | -0.3 | | 1.5 | V | 以 VSS 为基准 | 59 |
| 输入电压 (3.3V) | VIN | -0.3 | | 4.6 | V | | 59 |
| 输出电压 | VO | -0.3 | | 4.6 | V | | 59 |
| 数字输入钳位电流(每引脚) | IIK | -20 | | 20 | mA | VIN < VSS 或 VIN > VDDIO | 59 |
| 模拟输入钳位电流(每引脚) | IIKANALOG | -20 | | 20 | mA | VIN < VSSA 或 VIN > VDDA | 59 |
| 所有输入钳位电流总计 | IIKTOTAL | -20 | | 20 | mA | VIN < VSS/VSSA 或 VIN > VDDIO/VDDA | 59 |
| 数字输出电流(每引脚) | IOUT | -20 | | 20 | mA | | 59 |
| 自然通风温度 | TA | -40 | | 125 | °C | | 59 |
| 工作结温 | TJ | -40 | | 150 | °C | | 59 |
| 贮存温度 | Tstg | -65 | | 150 | °C | | 59 |
| 器件电源电压 VDDIO 和 VDDA | VDDIO | | 3.3 | 3.63 | V | 启用内部 BOR | 60 |
| 器件电源电压 VDDIO 和 VDDA | VDDIO | 2.8 | 3.3 | 3.63 | V | 禁用内部 BOR | 60 |
| 器件电源电压 VDD | VDD | 1.14 | 1.2 | 1.32 | V | | 60 |
| 结温 TJ(S 版本) | TJ | -40 | | 125 | °C | S 版本 | 60 |
| 自然通风温度 TA(Q 版本) | TA | -40 | | 125 | °C | Q 版本(AEC Q100 认证) | 60 |
| 高电平输入电压 (3.3V) | VIH | 2 | | | V | | 68 |
| 低电平输入电压 (3.3V) | VIL | | | 0.8 | V | | 68 |
| 输入迟滞 | VHYSTERESIS | 150 | | | mV | | 68 |
| VDDIO 欠压复位电压 | VBOR-VDDIO | 2.81 | | 3 | V | | 68 |
| 运行模式 VDD 电流消耗 | IDD | | 61 | 90 | mA | 运行模式 | 62 |
| 运行模式 VDDIO 电流消耗 | IDDIO | | 26 | 45 | mA | 运行模式 | 62 |
| 运行模式 VDDA 电流消耗 | IDDA | | 12 | 30 | mA | 运行模式 | 62 |
| 空闲模式 VDD 电流消耗 | IDD | | 18 | 40 | mA | 空闲模式 | 62 |
| 空闲模式 VDDIO 电流消耗 | IDDIO | | 1.2 | 4 | mA | 空闲模式 | 62 |
| 空闲模式 VDDA 电流消耗 | IDDA | | 0.9 | 1.2 | mA | 空闲模式 | 62 |
| 停机模式 VDD 电流消耗 | IDD | | 0.9 | 20 | mA | 停机模式 | 62 |
| 停机模式 VDDIO 电流消耗 | IDDIO | | 0.8 | 4 | mA | 停机模式 | 62 |
| 停机模式 VDDA 电流消耗 | IDDA | | 0.2 | 0.5 | mA | 停机模式 | 62 |
| 闪存擦除/编程 VDD 电流消耗 | IDD | | 40 | 70 | mA | 擦除/编程周期 | 62 |
| 闪存擦除/编程 VDDIO 电流消耗 | IDDIO | | 33 | 75 | mA | 擦除/编程周期 | 62 |
| 闪存擦除/编程 VDDA 电流消耗 | IDDA | | 0.1 | 2.5 | mA | 擦除/编程周期 | 62 |
| 内部稳压器输出 | VVREG | 1.14 | 1.2 | 1.32 | V | | 81 |
| 内部振荡器频率 INTOSC1 和 INTOSC2 | fINTOSC | 9.7 | 10 | 10.3 | MHz | | 95 |
| 频率稳定性 | fINTOSC-STABILITY | -3 | | 3 | % | | 96 |
| ADCCLK(源自 PERx.SYSCLK) | | 5 | | 50 | MHz | | 124 |
| VREFHI 外部基准 | VREFHI | 2.4 | | | V | 外部基准 | 124 |
| ADC 增益误差(内部基准电压) | | -45 | | 45 | LSB | 内部基准电压 | 125 |
| ADC 增益误差(外部基准) | | -5 | | 5 | LSB | 外部基准 | 125 |
| ADC 偏移量误差 | | -5 | | 5 | LSB | | 125 |
| ADC DNL 误差 | | -1 | | 1 | LSB | | 125 |
| ADC INL 误差 | | -2 | | 2 | LSB | | 125 |
| 缓冲 DAC 有效输出电压范围 (RL=5kΩ) | VOUT | 0.3 | | | V | RL = 5kΩ | 137 |
| 缓冲 DAC 有效输出电压范围 (RL=1kΩ) | VOUT | 0.6 | | | V | RL = 1kΩ | 137 |
| 缓冲 DAC 增益误差 | | -2.5 | | 2.5 | FSR 百分比 | | 138 |
| 缓冲 DAC DNL | | -1 | | 1 | LSB | 已更正端点 | 138 |
| 缓冲 DAC INL | | -5 | | 5 | LSB | 已更正端点 | 138 |
| 比较器以输入为基准的偏移量误差 | | -20 | | 20 | mV | 低共模,反相输入设置为 50mV | 144 |
| CMPSS DAC 静态偏移量误差 | | -25 | | 25 | mV | | 145 |
| CMPSS DAC 静态增益误差 | | -2 | | 2 | FSR 百分比 | | 145 |
| CMPSS DAC 静态 DNL | | -1 | | 4 | LSB | 已更正端点 | 145 |
| CMPSS DAC 静态 INL | | -16 | | 16 | LSB | 已更正端点 | 145 |
| SCL 时钟频率(PMBus 快速模式) | fSCL | 10 | | 400 | kHz | 快速模式 | 177 |
| SCL 时钟频率(PMBus 标准模式) | fSCL | 10 | | 100 | kHz | 标准模式 | 178 |
| 结至外壳热阻 | RΘJC | | 7.6 | | °C/W | PZ 封装 | 69 |
| 结至电路板热阻 | RΘJB | | 24.2 | | °C/W | PZ 封装 | 69 |
| 结至大气热阻(高 k PCB) | RΘJA | | 46.1 | | °C/W | 高 k PCB,0 lfm,PZ 封装 | 69 |
## CAD (KiCad official)
- Symbol: `F280049PZQ`
- Footprint: `Package_QFP:TQFP-100_14x14mm_P0.5mm`
- 3D model: TQFP-100(14x14) (KiCad packages3D, STEP)
- 3D model files: `f280049pzq-etched.step` / `f280049pzq-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `f280049pzq.step` / `f280049pzq.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/f280049pzq.pdf) (270 pp, sha256 `f0eccdafc7ec75fa`, retrieved 2026-11-02, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/f280049pzq-datasheet.pdf)