component
F280049PMSR
Public Made by Adomby adom
Texas Instruments Microcontrollers (MCU/MPU/SOC), LQFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
ffbbc29
F280049PMSR
Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
F280049PMSR from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 (default GPIO function, multiplexed with SCIA_TX, EPWM7_B, EQEP1_B, LINA_RX, ERRORSTS and others); 3.3 V I/O with ±4 mA output drive. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 (default GPIO function, multiplexed with SCIA_RX, EPWM7_A, EQEP1_A, LINA_TX, ERRORSTS and others); 3.3 V I/O with ±4 mA output drive. |
| 3 | XRSn | bidirectional | Device reset input and watchdog reset output (open-drain with internal pullup); a 2.2 kΩ to 10 kΩ resistor must be placed between XRSn and VDDIO, and a capacitor of 100 nF or less may be placed to VSS for noise filtering. |
| 4 | VDD | power_in | 1.2 V digital logic supply pin; TI recommends a total decoupling capacitance of about 20 µF near the VDD pins. |
| 5 | VSS | power_in | Digital ground; must be connected to the board ground. |
| 6 | A6 | input | ADC-A analog input 6 (also PGA5_OF filter output and CMPSS-5 comparator input, and AIO228 digital input); 3.3 V analog input referenced to VSSA. |
| 7 | B2 | input | ADC-B analog input 2, also multiplexed with C6 (ADC-C input 6) and PGA3_OF filter output, and AIO226 digital input. |
| 8 | B3 | input | ADC-B analog input 3, also multiplexed with VDAC, an optional external reference for the on-chip DAC; a 100 pF capacitor to VSSA is always present and at least one 1 µF capacitor is required if VDAC is used as DAC reference. |
| 9 | A2 | input | ADC-A analog input 2, also multiplexed with B6 (ADC-B input 6), PGA1_OF filter output and AIO224 digital input. |
| 10 | PGA1_GND | power_in | PGA-1 Kelvin ground reference shared with PGA3_GND and PGA5_GND; ideally equal to VSSA and should be bound to VSSA when unused. |
| 11 | C4 | input | ADC-C analog input 4, also multiplexed with PGA5_IN (PGA-5 input) and CMPSS-5 comparator inputs, and AIO239 digital input. |
| 12 | C0 | input | ADC-C analog input 0, also multiplexed with PGA1_IN (PGA-1 input) and CMPSS-1 comparator inputs, and AIO237 digital input. |
| 13 | C2 | input | ADC-C analog input 2, also multiplexed with PGA3_IN (PGA-3 input) and CMPSS-3 comparator inputs, and AIO244 digital input. |
| 14 | A1 | input | ADC-A analog input 1, also multiplexed with buffered DAC-B output DACB_OUT and AIO232 digital input. |
| 15 | A0 | input | ADC-A analog input 0, also multiplexed with ADC-B input B15, ADC-C input C15, buffered DAC-A output DACA_OUT and AIO231 digital input. |
| 16 | VREFHIA | bidirectional | ADC-A high reference; driven externally in external-reference mode or generated by the device in internal-reference mode, with at least one 2.2 µF capacitor between VREFHIA and VREFLOA, and must not be loaded externally. Shared pin position with VREFHIB/VREFHIC on this package. |
| 17 | VREFLOA | input | ADC-A low reference, shared with VREFLOB and VREFLOC on this package; bind to VSSA when used. |
| 18 | C1 | input | ADC-C analog input 1, also multiplexed with PGA2_IN (PGA-2 input) and CMPSS-2 comparator inputs, and AIO238 digital input. |
| 19 | C3 | input | ADC-C analog input 3, also multiplexed with PGA4_IN (PGA-4 input) and CMPSS-4 comparator inputs, and AIO245 digital input. |
| 20 | PGA2_GND | power_in | Shared PGA-2, PGA-4 and PGA-6 Kelvin ground reference; ideally equal to VSSA and should be bound to VSSA when unused. |
| 21 | VSSA | power_in | Analog ground for the ADC, DAC, PGA and CMPSS subsystems. |
| 22 | VDDA | power_in | 3.3 V analog supply pin; a decoupling capacitor of at least 2.2 µF to VSSA is required on each VDDA pin. |
| 23 | A4 | input | ADC-A analog input 4, also multiplexed with B8 (ADC-B input 8), PGA2_OF filter output and AIO225 digital input. |
| 24 | B4 | input | ADC-B analog input 4, also multiplexed with C8 (ADC-C input 8), PGA4_OF filter output and AIO227 digital input. |
| 25 | A10 | input | ADC-A analog input 10, also multiplexed with B1, C10 and PGA7_OF filter output, and AIO230 digital input. |
| 26 | VSS | power_in | Digital ground pin; must be connected to the board ground. |
| 27 | VDD | power_in | 1.2 V digital logic supply pin; decoupling capacitance required near each VDD pin. |
| 28 | VDDIO | power_in | 3.3 V digital I/O supply pin; a decoupling capacitor of at least 0.1 µF is required on each VDDIO pin. |
| 29 | GPIO13 | bidirectional | General-purpose I/O 13 (multiplexed with EPWM7_B, CANB_RX, EQEP1_INDEX, SCIB_RX, PMBUSA_ALERT as open-drain and FSIRXA_CLK); 3.3 V I/O with ±4 mA output drive. |
| 30 | GPIO12 | bidirectional | General-purpose I/O 12 (multiplexed with EPWM7_A, CANB_TX, EQEP1_STROBE, SCIB_TX, PMBUSA_CTL and FSIRXA_D0); 3.3 V I/O with ±4 mA output drive. |
| 31 | GPIO11 | bidirectional | General-purpose I/O 11 (multiplexed with EPWM6_B, SCIB_RX, OUTPUTXBAR7, EQEP1_B, SPIA_STE and FSIRXA_D1); 3.3 V I/O with ±4 mA output drive. |
| 32 | GPIO33 | bidirectional | General-purpose I/O 33 (multiplexed with I2CA_SCL open-drain, SPIB_STE, OUTPUTXBAR4, LINA_RX, SD1_C3, FSIRXA_CLK and CANA_RX); 3.3 V I/O with ±4 mA output drive. |
| 33 | GPIO16 | bidirectional | General-purpose I/O 16 (multiplexed with SPIA_SIMO, CANB_TX, OUTPUTXBAR7, EPWM5_A, SCIA_TX, SD1_D1, XCLKOUT and others); 3.3 V I/O with ±4 mA output drive. |
| 34 | GPIO17 | bidirectional | General-purpose I/O 17 (multiplexed with SPIA_SOMI, CANB_RX, OUTPUTXBAR8, EPWM5_B, SCIA_RX, SD1_C1, EQEP1_INDEX and PMBUSA_SDA); 3.3 V I/O with ±4 mA output drive. |
| 35 | GPIO24 | bidirectional | General-purpose I/O 24 (multiplexed with OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SD1_D1, PMBUSA_SCL, SCIA_TX and ERRORSTS); 3.3 V I/O with ±4 mA output drive. |
| 36 | TCK | input | JTAG test clock input with internal pullup enabled at reset. |
| 37 | GPIO37/TDO | output | JTAG test data output (TDO) by default; the pin is tri-stated when no JTAG activity is present, so an internal pullup or external pullup is recommended; can alternatively be used as GPIO37. |
| 38 | TMS | bidirectional | JTAG test mode select with internal pullup; an external pullup of about 2.2 kΩ to VDDIO is recommended to hold JTAG in reset during normal operation. |
| 39 | GPIO35/TDI | input | JTAG test data input (TDI) by default with internal pullup disabled; enable the internal pullup or add an external pullup when used as TDI to avoid a floating input; can alternatively be used as GPIO35. |
| 40 | GPIO32 | bidirectional | General-purpose I/O 32 (multiplexed with I2CA_SDA open-drain, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3, FSIRXA_D0 and CANA_TX); 3.3 V I/O with ±4 mA output drive. |
| 41 | GPIO18_X2 | bidirectional | General-purpose I/O 18 or crystal oscillator output X2; the GPIO function is only usable when the system is clocked from INTOSC and X1 has an external pulldown (recommended 1 kΩ). |
| 42 | X1 | bidirectional | Crystal oscillator input or single-ended 3.3 V clock input; the device initialization software must configure this pin before enabling the crystal oscillator, and GPIO19 must not be used on this pin. |
| 43 | VDDIO | power_in | 3.3 V digital I/O supply pin; a decoupling capacitor of at least 0.1 µF is required on each VDDIO pin. |
| 44 | VDD | power_in | 1.2 V digital logic supply pin; decoupling capacitance required near each VDD pin. |
| 45 | VSS | power_in | Digital ground pin; must be connected to the board ground. |
| 46 | VREGENZ | input | Internal regulator enable with internal pulldown; tie to VSS to enable the internal VREG, or to VDDIO to use an external VDD supply. |
| 47 | GPIO8 | bidirectional | General-purpose I/O 8 (multiplexed with EPWM5_A, CANB_TX, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL open-drain and FSITXA_D1); 3.3 V I/O with ±4 mA output drive. |
| 48 | GPIO4 | bidirectional | General-purpose I/O 4 (multiplexed with EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK); 3.3 V I/O with ±4 mA output drive. |
| 49 | GPIO3 | bidirectional | General-purpose I/O 3 (multiplexed with EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL open-drain, SPIA_CLK, SCIA_RX and FSIRXA_D0); 3.3 V I/O with ±4 mA output drive. |
| 50 | GPIO2 | bidirectional | General-purpose I/O 2 (multiplexed with EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA open-drain, SCIA_TX and FSIRXA_D1); 3.3 V I/O with ±4 mA output drive. |
| 51 | GPIO1 | bidirectional | General-purpose I/O 1 (multiplexed with EPWM1_B and I2CA_SCL open-drain); 3.3 V I/O with ±4 mA output drive. |
| 52 | GPIO0 | bidirectional | General-purpose I/O 0 (multiplexed with EPWM1_A and I2CA_SDA open-drain); 3.3 V I/O with ±4 mA output drive. |
| 53 | VDDIO_SW | power_in | 3.3 V supply for the internal DC/DC regulator; a 20 µF bulk input capacitor is required when the DC/DC is used and this pin must be connected to VDDIO. |
| 54 | GPIO23_VSW | bidirectional | General-purpose I/O 23 by default configured as the DC/DC switch output VSW when the internal DC/DC regulator is enabled; the pin has about 100 pF internal capacitance and is not recommended for fast-switching GPIO use. |
| 55 | VSS_SW | power_in | Internal DC/DC regulator ground; must be connected to the VSS pin. |
| 56 | GPIO22_VFBSW | bidirectional | General-purpose I/O 22 by default configured as the DC/DC feedback input VFBSW when the internal DC/DC regulator is enabled; if the DC/DC is unused it can be used as GPIO22. |
| 57 | GPIO7 | bidirectional | General-purpose I/O 7 (multiplexed with EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK); 3.3 V I/O with ±4 mA output drive. |
| 58 | VSS | power_in | Digital ground pin; must be connected to the board ground. |
| 59 | VDD | power_in | 1.2 V digital logic supply pin; decoupling capacitance required near each VDD pin. |
| 60 | VDDIO | power_in | 3.3 V digital I/O supply pin; a decoupling capacitor of at least 0.1 µF is required on each VDDIO pin. |
| 61 | GPIO5 | bidirectional | General-purpose I/O 5 (multiplexed with EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1); 3.3 V I/O with ±4 mA output drive. |
| 62 | GPIO9 | bidirectional | General-purpose I/O 9 (multiplexed with EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX, SPIA_CLK and FSITXA_D0); 3.3 V I/O with ±4 mA output drive. |
| 63 | GPIO10 | bidirectional | General-purpose I/O 10 (multiplexed with EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI, I2CA_SDA open-drain and FSITXA_CLK); 3.3 V I/O with ±4 mA output drive. |
| 64 | GPIO6 | bidirectional | General-purpose I/O 6 (multiplexed with EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0); 3.3 V I/O with ±4 mA output drive. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 电源电压 VDDIO(以 VSS 为基准) | VDDIO | -0.3 | 4.6 | V | 以 VSS 为基准 | 58 | |
| 电源电压 VDDA(以 VSSA 为基准) | VDDA | -0.3 | 4.6 | V | 以 VSSA 为基准 | 58 | |
| 电源电压 VDD(以 VSS 为基准) | VDD | -0.3 | 1.5 | V | 以 VSS 为基准 | 58 | |
| 输入电压 VIN (3.3V) | VIN | -0.3 | 4.6 | V | 3.3V 输入 | 58 | |
| 输出电压 | VO | -0.3 | 4.6 | V | 58 | ||
| 数字输入钳位电流(每引脚) | IIK | -20 | 20 | mA | VIN < VSS 或 VIN > VDDIO | 58 | |
| 模拟输入钳位电流(每引脚) | IIKANALOG | -20 | 20 | mA | VIN < VSSA 或 VIN > VDDA | 58 | |
| 所有输入钳位电流总计 | IIKTOTAL | -20 | 20 | mA | VIN < VSS/VSSA 或 VIN > VDDIO/VDDA | 58 | |
| 数字输出电流(每引脚) | IOUT | -20 | 20 | mA | 数字输出(每引脚) | 58 | |
| 自然通风温度 | TA | -40 | 125 | °C | 58 | ||
| 工作结温 | TJ | -40 | 150 | °C | 58 | ||
| 贮存温度 | Tstg | -65 | 150 | °C | 58 | ||
| 器件电源电压 VDDIO 和 VDDA(启用内部 BOR) | VDDIO, VDDA | 3.3 | 3.63 | V | 启用内部 BOR | 59 | |
| 器件电源电压 VDDIO 和 VDDA(禁用内部 BOR) | VDDIO, VDDA | 2.8 | 3.3 | 3.63 | V | 禁用内部 BOR | 59 |
| 器件电源电压 VDD | VDD | 1.14 | 1.2 | 1.32 | V | 59 | |
| 结温 TJ(S 版本) | TJ | -40 | 125 | °C | S 版本 | 59 | |
| VDD 运行期间电流消耗 | IDD | 61 | 90 | mA | 运行期间;请参阅节 6.5.4 | 61 | |
| VDDIO 运行期间电流消耗 | IDDIO | 26 | 45 | mA | 运行期间;请参阅节 6.5.4 | 61 | |
| VDDA 运行期间电流消耗 | IDDA | 12 | 30 | mA | 运行期间;请参阅节 6.5.4 | 61 | |
| VDD 空闲模式电流消耗 | IDD | 18 | 40 | mA | CPU 处于空闲模式;闪存断电;XCLKOUT 关闭 | 61 | |
| VDDIO 空闲模式电流消耗 | IDDIO | 1.2 | 4 | mA | CPU 处于空闲模式;闪存断电;XCLKOUT 关闭 | 61 | |
| VDDA 空闲模式电流消耗 | IDDA | 0.9 | 1.2 | mA | CPU 处于空闲模式;闪存断电;XCLKOUT 关闭 | 61 | |
| VDD 停机模式电流消耗 | IDD | 0.9 | 20 | mA | CPU 处于停机模式;闪存断电;XCLKOUT 关闭 | 61 | |
| VDDIO 停机模式电流消耗 | IDDIO | 0.8 | 4 | mA | CPU 处于停机模式;闪存断电;XCLKOUT 关闭 | 61 | |
| VDDA 停机模式电流消耗 | IDDA | 0.2 | 0.5 | mA | CPU 处于停机模式;闪存断电;XCLKOUT 关闭 | 61 | |
| VDD 擦除/编程周期电流消耗 | IDD | 40 | 70 | mA | 擦除/编程周期;禁用 VREG;SYSCLK 100MHz | 61 | |
| VDDIO 擦除/编程周期电流消耗 | IDDIO | 33 | 75 | mA | 擦除/编程周期;禁用 VREG;SYSCLK 100MHz | 61 | |
| VDDA 擦除/编程周期电流消耗 | IDDA | 0.1 | 2.5 | mA | 擦除/编程周期;禁用 VREG;SYSCLK 100MHz | 61 | |
| VDDIO 运行期间电流消耗(内部 VREG) | IDDIO | 86 | 113 | mA | 内部 VREG;请参阅节 6.5.4 | 61 | |
| VDDA 运行期间电流消耗(内部 VREG) | IDDA | 12 | 30 | mA | 内部 VREG;请参阅节 6.5.4 | 61 | |
| 低电平输出电压 | VOL | 0.4 | V | IOL=IOL 最大值 | 67 | ||
| 低电平输出电压 | VOL | 0.2 | V | IOL = 100µA | 67 | ||
| 高电平输入电压 (3.3V) | VIH | 2 | V | (3.3V) | 67 | ||
| 低电平输入电压 (3.3V) | VIL | 0.8 | V | (3.3V) | 67 | ||
| VDDIO 欠压复位电压 | VBOR-VDDIO | 2.81 | 3 | V | 67 | ||
| 晶振负载电容 | CL1、CL2 | 12 | 24 | pF | 93 | ||
| 晶振并联电容 | C0 | 7 | pF | 93 | |||
| 内部振荡器频率 INTOSC1 和 INTOSC2 | fINTOSC | 9.7 | 10 | 10.3 | MHz | 94 | |
| 室温下的频率稳定性 | fINTOSC-STABILITY | -0.1 | 0.1 | % | 30°C,标称 VDD | 95 | |
| VDD 上的频率稳定性 | fINTOSC-STABILITY | -0.2 | 0.2 | % | 30°C | 95 | |
| 频率稳定性 | fINTOSC-STABILITY | -3 | 3 | % | 95 | ||
| 内部稳压器输出 VVREG | VVREG | 1.14 | 1.2 | 1.32 | V | 80 | |
| VDDIO 斜降欠压复位电压 | VBOR-VDDIO-DN | 2.81 | 3 | V | XRSn 释放之后 | 80 | |
| 低功耗唤醒脉冲持续时间 tw(WAKE)(无输入限定器) | tw(WAKE) | 2 | tc(SYSCLK) 周期 | 无输入限定器 | 108 | ||
| ADCCLK(源自 PERx.SYSCLK) | ADCCLK | 5 | 50 | MHz | 123 | ||
| VREFHI 外部基准 | VREFHI | 2.4 | V | 外部基准 | 123 | ||
| VREFHI - VREFLO 外部基准 | VREFHI - VREFLO | 2.4 | V | 外部基准 | 123 | ||
| ADC 转换范围 | 0 | 3.3 | V | 内部基准电压 = 3.3V 范围 | 123 | ||
| ADC 转换范围 | 0 | 2.5 | V | 内部基准电压 = 2.5V 范围 | 123 | ||
| ADC 转换周期 | 10.1 | 11 | ADCCLK | 100MHz SYSCLK | 124 | ||
| 增益误差 | -45 | 45 | LSB | 内部基准电压 | 124 | ||
| 增益误差 | -5 | 5 | LSB | 外部基准 | 124 | ||
| 偏移量误差 | -5 | 5 | LSB | 124 | |||
| DNL 误差 | DNL | -1 | 1 | LSB | 124 | ||
| INL 误差 | INL | -2 | 2 | LSB | 124 | ||
| ADC 间隔离 | -1 | 1 | LSB | VREFHI = 2.5V,同步 ADC | 124 | ||
| 缓冲 DAC 有效输出电压(下限) | VOUT | 0.3 | V | RL = 5kΩ | 136 | ||
| 缓冲 DAC 有效输出电压(下限) | VOUT | 0.6 | V | RL = 1kΩ | 136 | ||
| 缓冲 DAC 基准电压 | 2.4 | V | VDAC 或 VREFHI | 136 | |||
| 输入电流(PMBus 每引脚) | Ii | -10 | 10 | µA | 0.1Vbus < Vi < 0.9Vbus | 176 |
CAD (KiCad official)
- Symbol:
F280049PMSR - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
f280049pmsr-etched.step/f280049pmsr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280049pmsr.step/f280049pmsr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (277 pp, sha256
867e7bb5ada6819c, retrieved 2026-11-10, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# F280049PMSR
**Texas Instruments** · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
F280049PMSR from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 (default GPIO function, multiplexed with SCIA_TX, EPWM7_B, EQEP1_B, LINA_RX, ERRORSTS and others); 3.3 V I/O with ±4 mA output drive. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 (default GPIO function, multiplexed with SCIA_RX, EPWM7_A, EQEP1_A, LINA_TX, ERRORSTS and others); 3.3 V I/O with ±4 mA output drive. |
| 3 | XRSn | bidirectional | Device reset input and watchdog reset output (open-drain with internal pullup); a 2.2 kΩ to 10 kΩ resistor must be placed between XRSn and VDDIO, and a capacitor of 100 nF or less may be placed to VSS for noise filtering. |
| 4 | VDD | power_in | 1.2 V digital logic supply pin; TI recommends a total decoupling capacitance of about 20 µF near the VDD pins. |
| 5 | VSS | power_in | Digital ground; must be connected to the board ground. |
| 6 | A6 | input | ADC-A analog input 6 (also PGA5_OF filter output and CMPSS-5 comparator input, and AIO228 digital input); 3.3 V analog input referenced to VSSA. |
| 7 | B2 | input | ADC-B analog input 2, also multiplexed with C6 (ADC-C input 6) and PGA3_OF filter output, and AIO226 digital input. |
| 8 | B3 | input | ADC-B analog input 3, also multiplexed with VDAC, an optional external reference for the on-chip DAC; a 100 pF capacitor to VSSA is always present and at least one 1 µF capacitor is required if VDAC is used as DAC reference. |
| 9 | A2 | input | ADC-A analog input 2, also multiplexed with B6 (ADC-B input 6), PGA1_OF filter output and AIO224 digital input. |
| 10 | PGA1_GND | power_in | PGA-1 Kelvin ground reference shared with PGA3_GND and PGA5_GND; ideally equal to VSSA and should be bound to VSSA when unused. |
| 11 | C4 | input | ADC-C analog input 4, also multiplexed with PGA5_IN (PGA-5 input) and CMPSS-5 comparator inputs, and AIO239 digital input. |
| 12 | C0 | input | ADC-C analog input 0, also multiplexed with PGA1_IN (PGA-1 input) and CMPSS-1 comparator inputs, and AIO237 digital input. |
| 13 | C2 | input | ADC-C analog input 2, also multiplexed with PGA3_IN (PGA-3 input) and CMPSS-3 comparator inputs, and AIO244 digital input. |
| 14 | A1 | input | ADC-A analog input 1, also multiplexed with buffered DAC-B output DACB_OUT and AIO232 digital input. |
| 15 | A0 | input | ADC-A analog input 0, also multiplexed with ADC-B input B15, ADC-C input C15, buffered DAC-A output DACA_OUT and AIO231 digital input. |
| 16 | VREFHIA | bidirectional | ADC-A high reference; driven externally in external-reference mode or generated by the device in internal-reference mode, with at least one 2.2 µF capacitor between VREFHIA and VREFLOA, and must not be loaded externally. Shared pin position with VREFHIB/VREFHIC on this package. |
| 17 | VREFLOA | input | ADC-A low reference, shared with VREFLOB and VREFLOC on this package; bind to VSSA when used. |
| 18 | C1 | input | ADC-C analog input 1, also multiplexed with PGA2_IN (PGA-2 input) and CMPSS-2 comparator inputs, and AIO238 digital input. |
| 19 | C3 | input | ADC-C analog input 3, also multiplexed with PGA4_IN (PGA-4 input) and CMPSS-4 comparator inputs, and AIO245 digital input. |
| 20 | PGA2_GND | power_in | Shared PGA-2, PGA-4 and PGA-6 Kelvin ground reference; ideally equal to VSSA and should be bound to VSSA when unused. |
| 21 | VSSA | power_in | Analog ground for the ADC, DAC, PGA and CMPSS subsystems. |
| 22 | VDDA | power_in | 3.3 V analog supply pin; a decoupling capacitor of at least 2.2 µF to VSSA is required on each VDDA pin. |
| 23 | A4 | input | ADC-A analog input 4, also multiplexed with B8 (ADC-B input 8), PGA2_OF filter output and AIO225 digital input. |
| 24 | B4 | input | ADC-B analog input 4, also multiplexed with C8 (ADC-C input 8), PGA4_OF filter output and AIO227 digital input. |
| 25 | A10 | input | ADC-A analog input 10, also multiplexed with B1, C10 and PGA7_OF filter output, and AIO230 digital input. |
| 26 | VSS | power_in | Digital ground pin; must be connected to the board ground. |
| 27 | VDD | power_in | 1.2 V digital logic supply pin; decoupling capacitance required near each VDD pin. |
| 28 | VDDIO | power_in | 3.3 V digital I/O supply pin; a decoupling capacitor of at least 0.1 µF is required on each VDDIO pin. |
| 29 | GPIO13 | bidirectional | General-purpose I/O 13 (multiplexed with EPWM7_B, CANB_RX, EQEP1_INDEX, SCIB_RX, PMBUSA_ALERT as open-drain and FSIRXA_CLK); 3.3 V I/O with ±4 mA output drive. |
| 30 | GPIO12 | bidirectional | General-purpose I/O 12 (multiplexed with EPWM7_A, CANB_TX, EQEP1_STROBE, SCIB_TX, PMBUSA_CTL and FSIRXA_D0); 3.3 V I/O with ±4 mA output drive. |
| 31 | GPIO11 | bidirectional | General-purpose I/O 11 (multiplexed with EPWM6_B, SCIB_RX, OUTPUTXBAR7, EQEP1_B, SPIA_STE and FSIRXA_D1); 3.3 V I/O with ±4 mA output drive. |
| 32 | GPIO33 | bidirectional | General-purpose I/O 33 (multiplexed with I2CA_SCL open-drain, SPIB_STE, OUTPUTXBAR4, LINA_RX, SD1_C3, FSIRXA_CLK and CANA_RX); 3.3 V I/O with ±4 mA output drive. |
| 33 | GPIO16 | bidirectional | General-purpose I/O 16 (multiplexed with SPIA_SIMO, CANB_TX, OUTPUTXBAR7, EPWM5_A, SCIA_TX, SD1_D1, XCLKOUT and others); 3.3 V I/O with ±4 mA output drive. |
| 34 | GPIO17 | bidirectional | General-purpose I/O 17 (multiplexed with SPIA_SOMI, CANB_RX, OUTPUTXBAR8, EPWM5_B, SCIA_RX, SD1_C1, EQEP1_INDEX and PMBUSA_SDA); 3.3 V I/O with ±4 mA output drive. |
| 35 | GPIO24 | bidirectional | General-purpose I/O 24 (multiplexed with OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SD1_D1, PMBUSA_SCL, SCIA_TX and ERRORSTS); 3.3 V I/O with ±4 mA output drive. |
| 36 | TCK | input | JTAG test clock input with internal pullup enabled at reset. |
| 37 | GPIO37/TDO | output | JTAG test data output (TDO) by default; the pin is tri-stated when no JTAG activity is present, so an internal pullup or external pullup is recommended; can alternatively be used as GPIO37. |
| 38 | TMS | bidirectional | JTAG test mode select with internal pullup; an external pullup of about 2.2 kΩ to VDDIO is recommended to hold JTAG in reset during normal operation. |
| 39 | GPIO35/TDI | input | JTAG test data input (TDI) by default with internal pullup disabled; enable the internal pullup or add an external pullup when used as TDI to avoid a floating input; can alternatively be used as GPIO35. |
| 40 | GPIO32 | bidirectional | General-purpose I/O 32 (multiplexed with I2CA_SDA open-drain, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3, FSIRXA_D0 and CANA_TX); 3.3 V I/O with ±4 mA output drive. |
| 41 | GPIO18_X2 | bidirectional | General-purpose I/O 18 or crystal oscillator output X2; the GPIO function is only usable when the system is clocked from INTOSC and X1 has an external pulldown (recommended 1 kΩ). |
| 42 | X1 | bidirectional | Crystal oscillator input or single-ended 3.3 V clock input; the device initialization software must configure this pin before enabling the crystal oscillator, and GPIO19 must not be used on this pin. |
| 43 | VDDIO | power_in | 3.3 V digital I/O supply pin; a decoupling capacitor of at least 0.1 µF is required on each VDDIO pin. |
| 44 | VDD | power_in | 1.2 V digital logic supply pin; decoupling capacitance required near each VDD pin. |
| 45 | VSS | power_in | Digital ground pin; must be connected to the board ground. |
| 46 | VREGENZ | input | Internal regulator enable with internal pulldown; tie to VSS to enable the internal VREG, or to VDDIO to use an external VDD supply. |
| 47 | GPIO8 | bidirectional | General-purpose I/O 8 (multiplexed with EPWM5_A, CANB_TX, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL open-drain and FSITXA_D1); 3.3 V I/O with ±4 mA output drive. |
| 48 | GPIO4 | bidirectional | General-purpose I/O 4 (multiplexed with EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK); 3.3 V I/O with ±4 mA output drive. |
| 49 | GPIO3 | bidirectional | General-purpose I/O 3 (multiplexed with EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL open-drain, SPIA_CLK, SCIA_RX and FSIRXA_D0); 3.3 V I/O with ±4 mA output drive. |
| 50 | GPIO2 | bidirectional | General-purpose I/O 2 (multiplexed with EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA open-drain, SCIA_TX and FSIRXA_D1); 3.3 V I/O with ±4 mA output drive. |
| 51 | GPIO1 | bidirectional | General-purpose I/O 1 (multiplexed with EPWM1_B and I2CA_SCL open-drain); 3.3 V I/O with ±4 mA output drive. |
| 52 | GPIO0 | bidirectional | General-purpose I/O 0 (multiplexed with EPWM1_A and I2CA_SDA open-drain); 3.3 V I/O with ±4 mA output drive. |
| 53 | VDDIO_SW | power_in | 3.3 V supply for the internal DC/DC regulator; a 20 µF bulk input capacitor is required when the DC/DC is used and this pin must be connected to VDDIO. |
| 54 | GPIO23_VSW | bidirectional | General-purpose I/O 23 by default configured as the DC/DC switch output VSW when the internal DC/DC regulator is enabled; the pin has about 100 pF internal capacitance and is not recommended for fast-switching GPIO use. |
| 55 | VSS_SW | power_in | Internal DC/DC regulator ground; must be connected to the VSS pin. |
| 56 | GPIO22_VFBSW | bidirectional | General-purpose I/O 22 by default configured as the DC/DC feedback input VFBSW when the internal DC/DC regulator is enabled; if the DC/DC is unused it can be used as GPIO22. |
| 57 | GPIO7 | bidirectional | General-purpose I/O 7 (multiplexed with EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK); 3.3 V I/O with ±4 mA output drive. |
| 58 | VSS | power_in | Digital ground pin; must be connected to the board ground. |
| 59 | VDD | power_in | 1.2 V digital logic supply pin; decoupling capacitance required near each VDD pin. |
| 60 | VDDIO | power_in | 3.3 V digital I/O supply pin; a decoupling capacitor of at least 0.1 µF is required on each VDDIO pin. |
| 61 | GPIO5 | bidirectional | General-purpose I/O 5 (multiplexed with EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1); 3.3 V I/O with ±4 mA output drive. |
| 62 | GPIO9 | bidirectional | General-purpose I/O 9 (multiplexed with EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX, SPIA_CLK and FSITXA_D0); 3.3 V I/O with ±4 mA output drive. |
| 63 | GPIO10 | bidirectional | General-purpose I/O 10 (multiplexed with EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI, I2CA_SDA open-drain and FSITXA_CLK); 3.3 V I/O with ±4 mA output drive. |
| 64 | GPIO6 | bidirectional | General-purpose I/O 6 (multiplexed with EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0); 3.3 V I/O with ±4 mA output drive. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| 电源电压 VDDIO(以 VSS 为基准) | VDDIO | -0.3 | | 4.6 | V | 以 VSS 为基准 | 58 |
| 电源电压 VDDA(以 VSSA 为基准) | VDDA | -0.3 | | 4.6 | V | 以 VSSA 为基准 | 58 |
| 电源电压 VDD(以 VSS 为基准) | VDD | -0.3 | | 1.5 | V | 以 VSS 为基准 | 58 |
| 输入电压 VIN (3.3V) | VIN | -0.3 | | 4.6 | V | 3.3V 输入 | 58 |
| 输出电压 | VO | -0.3 | | 4.6 | V | | 58 |
| 数字输入钳位电流(每引脚) | IIK | -20 | | 20 | mA | VIN < VSS 或 VIN > VDDIO | 58 |
| 模拟输入钳位电流(每引脚) | IIKANALOG | -20 | | 20 | mA | VIN < VSSA 或 VIN > VDDA | 58 |
| 所有输入钳位电流总计 | IIKTOTAL | -20 | | 20 | mA | VIN < VSS/VSSA 或 VIN > VDDIO/VDDA | 58 |
| 数字输出电流(每引脚) | IOUT | -20 | | 20 | mA | 数字输出(每引脚) | 58 |
| 自然通风温度 | TA | -40 | | 125 | °C | | 58 |
| 工作结温 | TJ | -40 | | 150 | °C | | 58 |
| 贮存温度 | Tstg | -65 | | 150 | °C | | 58 |
| 器件电源电压 VDDIO 和 VDDA(启用内部 BOR) | VDDIO, VDDA | | 3.3 | 3.63 | V | 启用内部 BOR | 59 |
| 器件电源电压 VDDIO 和 VDDA(禁用内部 BOR) | VDDIO, VDDA | 2.8 | 3.3 | 3.63 | V | 禁用内部 BOR | 59 |
| 器件电源电压 VDD | VDD | 1.14 | 1.2 | 1.32 | V | | 59 |
| 结温 TJ(S 版本) | TJ | -40 | | 125 | °C | S 版本 | 59 |
| VDD 运行期间电流消耗 | IDD | | 61 | 90 | mA | 运行期间;请参阅节 6.5.4 | 61 |
| VDDIO 运行期间电流消耗 | IDDIO | | 26 | 45 | mA | 运行期间;请参阅节 6.5.4 | 61 |
| VDDA 运行期间电流消耗 | IDDA | | 12 | 30 | mA | 运行期间;请参阅节 6.5.4 | 61 |
| VDD 空闲模式电流消耗 | IDD | | 18 | 40 | mA | CPU 处于空闲模式;闪存断电;XCLKOUT 关闭 | 61 |
| VDDIO 空闲模式电流消耗 | IDDIO | | 1.2 | 4 | mA | CPU 处于空闲模式;闪存断电;XCLKOUT 关闭 | 61 |
| VDDA 空闲模式电流消耗 | IDDA | | 0.9 | 1.2 | mA | CPU 处于空闲模式;闪存断电;XCLKOUT 关闭 | 61 |
| VDD 停机模式电流消耗 | IDD | | 0.9 | 20 | mA | CPU 处于停机模式;闪存断电;XCLKOUT 关闭 | 61 |
| VDDIO 停机模式电流消耗 | IDDIO | | 0.8 | 4 | mA | CPU 处于停机模式;闪存断电;XCLKOUT 关闭 | 61 |
| VDDA 停机模式电流消耗 | IDDA | | 0.2 | 0.5 | mA | CPU 处于停机模式;闪存断电;XCLKOUT 关闭 | 61 |
| VDD 擦除/编程周期电流消耗 | IDD | | 40 | 70 | mA | 擦除/编程周期;禁用 VREG;SYSCLK 100MHz | 61 |
| VDDIO 擦除/编程周期电流消耗 | IDDIO | | 33 | 75 | mA | 擦除/编程周期;禁用 VREG;SYSCLK 100MHz | 61 |
| VDDA 擦除/编程周期电流消耗 | IDDA | | 0.1 | 2.5 | mA | 擦除/编程周期;禁用 VREG;SYSCLK 100MHz | 61 |
| VDDIO 运行期间电流消耗(内部 VREG) | IDDIO | | 86 | 113 | mA | 内部 VREG;请参阅节 6.5.4 | 61 |
| VDDA 运行期间电流消耗(内部 VREG) | IDDA | | 12 | 30 | mA | 内部 VREG;请参阅节 6.5.4 | 61 |
| 低电平输出电压 | VOL | | | 0.4 | V | IOL=IOL 最大值 | 67 |
| 低电平输出电压 | VOL | | | 0.2 | V | IOL = 100µA | 67 |
| 高电平输入电压 (3.3V) | VIH | 2 | | | V | (3.3V) | 67 |
| 低电平输入电压 (3.3V) | VIL | | | 0.8 | V | (3.3V) | 67 |
| VDDIO 欠压复位电压 | VBOR-VDDIO | 2.81 | | 3 | V | | 67 |
| 晶振负载电容 | CL1、CL2 | 12 | | 24 | pF | | 93 |
| 晶振并联电容 | C0 | | | 7 | pF | | 93 |
| 内部振荡器频率 INTOSC1 和 INTOSC2 | fINTOSC | 9.7 | 10 | 10.3 | MHz | | 94 |
| 室温下的频率稳定性 | fINTOSC-STABILITY | -0.1 | | 0.1 | % | 30°C,标称 VDD | 95 |
| VDD 上的频率稳定性 | fINTOSC-STABILITY | -0.2 | | 0.2 | % | 30°C | 95 |
| 频率稳定性 | fINTOSC-STABILITY | -3 | | 3 | % | | 95 |
| 内部稳压器输出 VVREG | VVREG | 1.14 | 1.2 | 1.32 | V | | 80 |
| VDDIO 斜降欠压复位电压 | VBOR-VDDIO-DN | 2.81 | | 3 | V | XRSn 释放之后 | 80 |
| 低功耗唤醒脉冲持续时间 tw(WAKE)(无输入限定器) | tw(WAKE) | 2 | | | tc(SYSCLK) 周期 | 无输入限定器 | 108 |
| ADCCLK(源自 PERx.SYSCLK) | ADCCLK | 5 | | 50 | MHz | | 123 |
| VREFHI 外部基准 | VREFHI | 2.4 | | | V | 外部基准 | 123 |
| VREFHI - VREFLO 外部基准 | VREFHI - VREFLO | 2.4 | | | V | 外部基准 | 123 |
| ADC 转换范围 | | 0 | | 3.3 | V | 内部基准电压 = 3.3V 范围 | 123 |
| ADC 转换范围 | | 0 | | 2.5 | V | 内部基准电压 = 2.5V 范围 | 123 |
| ADC 转换周期 | | 10.1 | | 11 | ADCCLK | 100MHz SYSCLK | 124 |
| 增益误差 | | -45 | | 45 | LSB | 内部基准电压 | 124 |
| 增益误差 | | -5 | | 5 | LSB | 外部基准 | 124 |
| 偏移量误差 | | -5 | | 5 | LSB | | 124 |
| DNL 误差 | DNL | -1 | | 1 | LSB | | 124 |
| INL 误差 | INL | -2 | | 2 | LSB | | 124 |
| ADC 间隔离 | | -1 | | 1 | LSB | VREFHI = 2.5V,同步 ADC | 124 |
| 缓冲 DAC 有效输出电压(下限) | VOUT | 0.3 | | | V | RL = 5kΩ | 136 |
| 缓冲 DAC 有效输出电压(下限) | VOUT | 0.6 | | | V | RL = 1kΩ | 136 |
| 缓冲 DAC 基准电压 | | 2.4 | | | V | VDAC 或 VREFHI | 136 |
| 输入电流(PMBus 每引脚) | Ii | -10 | | 10 | µA | 0.1Vbus < Vi < 0.9Vbus | 176 |
## CAD (KiCad official)
- Symbol: `F280049PMSR`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `f280049pmsr-etched.step` / `f280049pmsr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `f280049pmsr.step` / `f280049pmsr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tms320f280045) (277 pp, sha256 `867e7bb5ada6819c`, retrieved 2026-11-10, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/f280049pmsr-datasheet.pdf)