component
F280049CPMS
Public Made by Adomby adom
Texas Instruments Microcontrollers (MCU/MPU/SOC), LQFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
27adf46
F280049CPMS
Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
F280049CPMS from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 (default GPIO), multiplexed with SCIA_TX, EPWM7_B, EQEP1_B, SPIB_STE, LINA_RX and ERRORSTS. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 (default GPIO), multiplexed with SCIA_RX, EPWM7_A, EQEP1_A, LINA_TX, SPIB_CLK and ERRORSTS. |
| 3 | XRSn | bidirectional | Device reset input and watchdog reset output (open-drain with internal pullup); a 2.2 kΩ to 10 kΩ resistor should be placed between XRSn and VDDIO, and any noise-filter capacitor should be 100 nF or less. |
| 4 | VDD | power_in | 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins. |
| 5 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 6 | A6/PGA5_OF | input | ADC-A input 6 (also PGA-5 optional output filter, CMPSS-5 comparator input and AIO228); keep the ADC input below VDDA + 0.3 V. |
| 7 | B2/C6/PGA3_OF | input | ADC-B input 2 (also ADC-C input 6, PGA-3 optional output filter and CMPSS-3 input); keep the ADC input below VDDA + 0.3 V. |
| 8 | B3/VDAC | input | ADC-B input 3 and optional external reference for the on-chip DAC; a 100 pF capacitor to VSSA is always present, and at least one 1 µF capacitor is required if used as the DAC reference. |
| 9 | A2/B6/PGA1_OF | input | ADC-A input 2 (also ADC-B input 6, PGA-1 optional output filter and CMPSS-1 input); keep the ADC input below VDDA + 0.3 V. |
| 10 | PGA1_GND | power_in | PGA-1, PGA-3 and PGA-5 ground (Kelvin ground reference, ideally equal to VSSA). |
| 11 | C4/PGA5_IN | input | ADC-C input 4 (also PGA-5 input and CMPSS-5 input); keep the ADC input below VDDA + 0.3 V. |
| 12 | C0/PGA1_IN | input | ADC-C input 0 (also PGA-1 input and CMPSS-1 input); keep the ADC input below VDDA + 0.3 V. |
| 13 | C2/PGA3_IN | input | ADC-C input 2 (also PGA-3 input and CMPSS-3 input); keep the ADC input below VDDA + 0.3 V. |
| 14 | A1/DACB_OUT | input | ADC-A input 1 (also buffered DAC-B output and AIO232); keep the ADC input below VDDA + 0.3 V. |
| 15 | A0/B15/C15/DACA_OUT | input | ADC-A input 0 (also ADC-B input 15, ADC-C input 15, buffered DAC-A output and AIO231); keep the ADC input below VDDA + 0.3 V. |
| 16 | VREFHIA | bidirectional | ADC-A/B/C high reference; drive externally in external-reference mode, device-driven in internal-reference mode, place at least 2.2 µF between each VREFHIx and its VREFLOx pin, and do not load externally. |
| 17 | VREFLOA | input | ADC-A/B/C low reference voltage; unused VREFLOx pins are tied to VSSA. |
| 18 | C1/PGA2_IN | input | ADC-C input 1 (also PGA-2 input and CMPSS-2 input); keep the ADC input below VDDA + 0.3 V. |
| 19 | C3/PGA4_IN | input | ADC-C input 3 (also PGA-4 input and CMPSS-4 input); keep the ADC input below VDDA + 0.3 V. |
| 20 | PGA2_GND | power_in | PGA-2, PGA-4 and PGA-6 ground (Kelvin ground reference, ideally equal to VSSA). |
| 21 | VSSA | power_in | Analog ground. |
| 22 | VDDA | power_in | 3.3 V analog supply; place a minimum 2.2 µF decoupling capacitor connected to VSSA on each VDDA pin. |
| 23 | A4/B8/PGA2_OF | input | ADC-A input 4 (also ADC-B input 8, PGA-2 optional output filter and CMPSS-2 input); keep the ADC input below VDDA + 0.3 V. |
| 24 | B4/C8/PGA4_OF | input | ADC-B input 4 (also ADC-C input 8, PGA-4 optional output filter and CMPSS-4 input); keep the ADC input below VDDA + 0.3 V. |
| 25 | A10/B1/C10/PGA7_OF | input | ADC-A input 10 (also ADC-B input 1, ADC-C input 10 and PGA-7 optional output filter); keep the ADC input below VDDA + 0.3 V. |
| 26 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 27 | VDD | power_in | 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins. |
| 28 | VDDIO | power_in | 3.3 V digital I/O supply; place a minimum 0.1 µF decoupling capacitor on each VDDIO pin. |
| 29 | GPIO13 | bidirectional | General-purpose I/O 13 (default GPIO), multiplexed with EPWM7_B, CANB_RX, EQEP1_INDEX, SCIB_RX, PMBUSA_ALERT and FSIRXA_CLK. |
| 30 | GPIO12 | bidirectional | General-purpose I/O 12 (default GPIO), multiplexed with EPWM7_A, CANB_TX, EQEP1_STROBE, SCIB_TX, PMBUSA_CTL and FSIRXA_D0. |
| 31 | GPIO11 | bidirectional | General-purpose I/O 11 (default GPIO), multiplexed with EPWM6_B, SCIB_RX, OUTPUTXBAR7, EQEP1_B, SPIA_STE and FSIRXA_D1. |
| 32 | GPIO33 | bidirectional | General-purpose I/O 33 (default GPIO), multiplexed with I2CA_SCL, SPIB_STE, OUTPUTXBAR4, LINA_RX, SD1_C3, FSIRXA_CLK and CANA_RX. |
| 33 | GPIO16 | bidirectional | General-purpose I/O 16 (default GPIO), multiplexed with SPIA_SIMO, CANB_TX, OUTPUTXBAR7, EPWM5_A, SCIA_TX, SD1_D1, EQEP1_STROBE, PMBUSA_SCL and XCLKOUT. |
| 34 | GPIO17 | bidirectional | General-purpose I/O 17 (default GPIO), multiplexed with SPIA_SOMI, CANB_RX, OUTPUTXBAR8, EPWM5_B, SCIA_RX, SD1_C1, EQEP1_INDEX and PMBUSA_SDA. |
| 35 | GPIO24 | bidirectional | General-purpose I/O 24 (default GPIO), multiplexed with OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SD1_D1, PMBUSA_SCL, SCIA_TX and ERRORSTS. |
| 36 | TCK | input | JTAG test clock input with internal pullup. |
| 37 | GPIO37/TDO | output | JTAG test data output (TDO, default function); the pin is tri-stated when there is no JTAG activity, so an internal or external pullup is required to avoid a floating GPIO input. |
| 38 | TMS | bidirectional | JTAG test mode select with internal pullup, clocked on TCK rising edge; a 2.2 kΩ external pullup to VDDIO is recommended on the board. |
| 39 | GPIO35/TDI | input | JTAG test data input (TDI, default function); enable the internal pullup or add an external pullup to avoid a floating input. |
| 40 | GPIO32 | bidirectional | General-purpose I/O 32 (default GPIO), multiplexed with I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3, FSIRXA_D0 and CANA_TX. |
| 41 | GPIO18_X2 | bidirectional | General-purpose I/O 18 also serving as the X2 crystal oscillator output; GPIO18 and its mux options are usable only when INTOSC clocks the system and X1 has an external pull-down (1 kΩ recommended). |
| 42 | X1 | bidirectional | Crystal oscillator or single-ended 3.3 V clock input; device initialization software must configure this pin before enabling the crystal oscillator. |
| 43 | VDDIO | power_in | 3.3 V digital I/O supply; place a minimum 0.1 µF decoupling capacitor on each VDDIO pin. |
| 44 | VDD | power_in | 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins. |
| 45 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 46 | VREGENZ | input | Internal regulator enable with internal pulldown; tie to VSS to enable the internal VREG and to VDDIO to use an external VDD supply. |
| 47 | GPIO8 | bidirectional | General-purpose I/O 8 (default GPIO), multiplexed with EPWM5_A, CANB_TX, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL and FSITXA_D1. |
| 48 | GPIO4 | bidirectional | General-purpose I/O 4 (default GPIO), multiplexed with EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK. |
| 49 | GPIO3 | bidirectional | General-purpose I/O 3 (default GPIO), multiplexed with EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and FSIRXA_D0. |
| 50 | GPIO2 | bidirectional | General-purpose I/O 2 (default GPIO), multiplexed with EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SCIA_TX and FSIRXA_D1. |
| 51 | GPIO1 | bidirectional | General-purpose I/O 1 (default GPIO), multiplexed with EPWM1_B and I2CA_SCL. |
| 52 | GPIO0 | bidirectional | General-purpose I/O 0 (default GPIO), multiplexed with EPWM1_A and I2CA_SDA. |
| 53 | VDDIO_SW | power_in | 3.3 V supply for the internal DC/DC regulator; if the DC/DC is used a 20 µF bulk input capacitor is required, and this pin must be tied to VDDIO. |
| 54 | GPIO23_VSW | bidirectional | General-purpose I/O 23 (default DC/DC mode) that serves as the internal DC/DC switching output VSW when DCDCEN = 1; it has about 100 pF internal capacitance, so an alternate GPIO is recommended where fast switching response is needed. |
| 55 | VSS_SW | power_in | Internal DC/DC regulator ground; must be tied to VSS. |
| 56 | GPIO22_VFBSW | bidirectional | General-purpose I/O 22 (default DC/DC mode) that serves as the internal DC/DC feedback VFBSW when DCDCEN = 1; connect it to the node where L(VSW) meets the VDD rail, as close to the device as possible. |
| 57 | GPIO7 | bidirectional | General-purpose I/O 7 (default GPIO), multiplexed with EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK. |
| 58 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 59 | VDD | power_in | 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins. |
| 60 | VDDIO | power_in | 3.3 V digital I/O supply; place a minimum 0.1 µF decoupling capacitor on each VDDIO pin. |
| 61 | GPIO5 | bidirectional | General-purpose I/O 5 (default GPIO), multiplexed with EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1. |
| 62 | GPIO9 | bidirectional | General-purpose I/O 9 (default GPIO), multiplexed with EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX, SPIA_CLK and FSITXA_D0. |
| 63 | GPIO10 | bidirectional | General-purpose I/O 10 (default GPIO), multiplexed with EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI, I2CA_SDA and FSITXA_CLK. |
| 64 | GPIO6 | bidirectional | General-purpose I/O 6 (default GPIO), multiplexed with EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDDIO 以 VSS 为基准 (供电电压,绝对最大额定值) | VDDIO | -0.3 | 4.6 | V | 以 VSS 为基准 | 58 | |
| VDDA 以 VSSA 为基准 (供电电压,绝对最大额定值) | VDDA | -0.3 | 4.6 | V | 以 VSSA 为基准 | 58 | |
| VDD 以 VSS 为基准 (内核供电电压,绝对最大额定值) | VDD | -0.3 | 1.5 | V | 以 VSS 为基准 | 58 | |
| VDDIO 和 VDDIO_SW 引脚之间的电压差 | -0.3 | 0.3 | V | 58 | |||
| 输入电压 VIN (3.3V) | VIN | -0.3 | 4.6 | V | 58 | ||
| 输出电压 | VO | -0.3 | 4.6 | V | 58 | ||
| 数字输入钳位电流(每引脚) | IIK | -20 | 20 | mA | VIN < VSS 或 VIN > VDDIO | 58 | |
| 模拟输入钳位电流(每引脚) | IIKANALOG | -20 | 20 | mA | VIN < VSSA 或 VIN > VDDA | 58 | |
| 所有输入的总计钳位电流 | IIKTOTAL | -20 | 20 | mA | VIN < VSS/VSSA 或 VIN > VDDIO/VDDA | 58 | |
| 数字输出电流(每引脚) | IOUT | -20 | 20 | mA | 58 | ||
| 自然通风温度 | TA | -40 | 125 | °C | 自然通风 | 58 | |
| 工作结温 | TJ | -40 | 150 | °C | 58 | ||
| 贮存温度 | Tstg | -65 | 150 | °C | 58 | ||
| 器件电源电压 VDDIO 和 VDDA(启用内部 BOR) | VDDIO, VDDA | 3.3 | 3.63 | V | 启用内部 BOR | 59 | |
| 器件电源电压 VDDIO 和 VDDA(禁用内部 BOR) | VDDIO, VDDA | 2.8 | 3.3 | 3.63 | V | 禁用内部 BOR | 59 |
| 器件电源电压 VDD | VDD | 1.14 | 1.2 | 1.32 | V | 59 | |
| VDDIO 电源斜坡时间 | tVDDIO-RAMP | 10 | ms | 从 1V 到 VBOR-VDDIO(MAX) | 59 | ||
| 结温 TJ(S 版本) | TJ | -40 | 125 | °C | S 版本 | 59 | |
| VDD 运行期间的电流消耗(外部电源) | IDD | 61 | 90 | mA | 请参阅节 6.5.4 | 61 | |
| VDDIO 运行期间的电流消耗(外部电源) | IDDIO | 26 | 45 | mA | 61 | ||
| VDDA 运行期间的电流消耗(外部电源) | IDDA | 12 | 30 | mA | 61 | ||
| 器件处于空闲模式时的 VDD 电流消耗 | IDD | 18 | 40 | mA | CPU 处于空闲模式;闪存被断电;XCLKOUT 被关闭 | 61 | |
| 器件处于空闲模式时的 VDDIO 电流消耗 | IDDIO | 1.2 | 4 | mA | 61 | ||
| 器件处于空闲模式时的 VDDA 电流消耗 | IDDA | 0.9 | 1.2 | mA | 61 | ||
| 器件处于停机模式时的 VDD 电流消耗 | IDD | 0.9 | 20 | mA | CPU 处于停机模式;闪存被断电;XCLKOUT 被关闭 | 61 | |
| 器件处于停机模式时的 VDDIO 电流消耗 | IDDIO | 0.8 | 4 | mA | 61 | ||
| 器件处于停机模式时的 VDDA 电流消耗 | IDDA | 0.2 | 0.5 | mA | 61 | ||
| 擦除/编程周期期间的 VDD 电流消耗 | IDD | 40 | 70 | mA | CPU 从闪存运行擦除/编程;禁用 VREG;SYSCLK 100MHz | 61 | |
| 擦除/编程周期期间的 VDDIO 电流消耗 | IDDIO | 33 | 75 | mA | 61 | ||
| 擦除/编程周期期间的 VDDA 电流消耗 | IDDA | 0.1 | 2.5 | mA | 61 | ||
| VDDIO 运行期间的电流消耗(内部 VREG) | IDDIO | 86 | 113 | mA | 请参阅节 6.5.4 | 61 | |
| VDDA 运行期间的电流消耗(内部 VREG) | IDDA | 12 | 30 | mA | 61 | ||
| 低电平输出电压 (IOL=IOL 最大值) | VOL | 0.4 | V | IOL=IOL 最大值 | 67 | ||
| 低电平输出电压 (IOL=100µA) | VOL | 0.2 | V | IOL = 100µA | 67 | ||
| 高电平输入电压 (3.3V) | VIH | 2 | V | 67 | |||
| 低电平输入电压 (3.3V) | VIL | 0.8 | V | 67 | |||
| VDDIO 欠压复位电压 | VBOR-VDDIO | 2.81 | 3 | V | 67 | ||
| 内部稳压器输出 | VVREG | 1.14 | 1.2 | 1.32 | V | 80 | |
| 斜降时的 VDDIO 欠压复位电压 | VBOR-VDDIO-DN | 2.81 | 3 | V | XRSn 释放之后 | 80 | |
| CL1、CL2 负载电容 | CL1, CL2 | 12 | 24 | pF | 93 | ||
| 晶振并联电容 | C0 | 7 | pF | 93 | |||
| fINTOSC 频率,INTOSC1 和 INTOSC2 | fINTOSC | 9.7 | 10 | 10.3 | MHz | 94 | |
| 室温下的频率稳定性 | fINTOSC-STABILITY | -0.1 | 0.1 | % | 30°C,标称 VDD | 95 | |
| VDD 上的频率稳定性 | fINTOSC-STABILITY | -0.2 | 0.2 | % | 30°C | 95 | |
| 频率稳定性 | fINTOSC-STABILITY | -3 | 3 | % | 95 | ||
| ADCCLK(源自 PERx.SYSCLK) | ADCCLK | 5 | 50 | MHz | 123 | ||
| 有效输出电压范围 VOUT (RL=5kΩ) | VOUT | 0.3 | V | RL = 5kΩ | 136 | ||
| 有效输出电压范围 VOUT (RL=1kΩ) | VOUT | 0.6 | V | RL = 1kΩ | 136 | ||
| 负载调整率 | -1 | 1 | mV/V | 136 | |||
| 偏移量误差 | -10 | 10 | mV | 中点 | 136 | ||
| 增益误差 | -2.5 | 2.5 | FSR 百分比 | 136 | |||
| 比较器输入 (CMPINxx) 范围 | 0 | V | 143 | ||||
| 以输入为基准的偏移量误差 | -20 | 20 | mV | 低共模,反相输入设置为 50mV | 143 | ||
| CMPSS DAC 静态偏移量误差 | -25 | 25 | mV | 144 | |||
| CMPSS DAC 静态增益误差 | -2 | 2 | FSR 百分比 | 144 | |||
| CMPSS DAC 静态 INL | INL | -16 | 16 | LSB | 已更正端点 | 144 | |
| CMPSS DAC 输出干扰 | -100 | 100 | LSB | 由同一 CMPSS 模块内的比较器跳闸或 CMPSS DAC 代码更改引起的误差 | 144 | ||
| VDAC 负载 | 6 | 8 | 10 | kΩ | 当 VDAC 为基准时 | 144 | |
| VBOR-GB VDDIO BOR 保护频带 | VBOR-GB | 0.1 | V | 59 |
CAD (KiCad official)
- Symbol:
F280049CPMS - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
f280049cpms-etched.step/f280049cpms-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280049cpms.step/f280049cpms.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (277 pp, sha256
867e7bb5ada6819c, retrieved 2026-11-10, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# F280049CPMS
**Texas Instruments** · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
F280049CPMS from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 (default GPIO), multiplexed with SCIA_TX, EPWM7_B, EQEP1_B, SPIB_STE, LINA_RX and ERRORSTS. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 (default GPIO), multiplexed with SCIA_RX, EPWM7_A, EQEP1_A, LINA_TX, SPIB_CLK and ERRORSTS. |
| 3 | XRSn | bidirectional | Device reset input and watchdog reset output (open-drain with internal pullup); a 2.2 kΩ to 10 kΩ resistor should be placed between XRSn and VDDIO, and any noise-filter capacitor should be 100 nF or less. |
| 4 | VDD | power_in | 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins. |
| 5 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 6 | A6/PGA5_OF | input | ADC-A input 6 (also PGA-5 optional output filter, CMPSS-5 comparator input and AIO228); keep the ADC input below VDDA + 0.3 V. |
| 7 | B2/C6/PGA3_OF | input | ADC-B input 2 (also ADC-C input 6, PGA-3 optional output filter and CMPSS-3 input); keep the ADC input below VDDA + 0.3 V. |
| 8 | B3/VDAC | input | ADC-B input 3 and optional external reference for the on-chip DAC; a 100 pF capacitor to VSSA is always present, and at least one 1 µF capacitor is required if used as the DAC reference. |
| 9 | A2/B6/PGA1_OF | input | ADC-A input 2 (also ADC-B input 6, PGA-1 optional output filter and CMPSS-1 input); keep the ADC input below VDDA + 0.3 V. |
| 10 | PGA1_GND | power_in | PGA-1, PGA-3 and PGA-5 ground (Kelvin ground reference, ideally equal to VSSA). |
| 11 | C4/PGA5_IN | input | ADC-C input 4 (also PGA-5 input and CMPSS-5 input); keep the ADC input below VDDA + 0.3 V. |
| 12 | C0/PGA1_IN | input | ADC-C input 0 (also PGA-1 input and CMPSS-1 input); keep the ADC input below VDDA + 0.3 V. |
| 13 | C2/PGA3_IN | input | ADC-C input 2 (also PGA-3 input and CMPSS-3 input); keep the ADC input below VDDA + 0.3 V. |
| 14 | A1/DACB_OUT | input | ADC-A input 1 (also buffered DAC-B output and AIO232); keep the ADC input below VDDA + 0.3 V. |
| 15 | A0/B15/C15/DACA_OUT | input | ADC-A input 0 (also ADC-B input 15, ADC-C input 15, buffered DAC-A output and AIO231); keep the ADC input below VDDA + 0.3 V. |
| 16 | VREFHIA | bidirectional | ADC-A/B/C high reference; drive externally in external-reference mode, device-driven in internal-reference mode, place at least 2.2 µF between each VREFHIx and its VREFLOx pin, and do not load externally. |
| 17 | VREFLOA | input | ADC-A/B/C low reference voltage; unused VREFLOx pins are tied to VSSA. |
| 18 | C1/PGA2_IN | input | ADC-C input 1 (also PGA-2 input and CMPSS-2 input); keep the ADC input below VDDA + 0.3 V. |
| 19 | C3/PGA4_IN | input | ADC-C input 3 (also PGA-4 input and CMPSS-4 input); keep the ADC input below VDDA + 0.3 V. |
| 20 | PGA2_GND | power_in | PGA-2, PGA-4 and PGA-6 ground (Kelvin ground reference, ideally equal to VSSA). |
| 21 | VSSA | power_in | Analog ground. |
| 22 | VDDA | power_in | 3.3 V analog supply; place a minimum 2.2 µF decoupling capacitor connected to VSSA on each VDDA pin. |
| 23 | A4/B8/PGA2_OF | input | ADC-A input 4 (also ADC-B input 8, PGA-2 optional output filter and CMPSS-2 input); keep the ADC input below VDDA + 0.3 V. |
| 24 | B4/C8/PGA4_OF | input | ADC-B input 4 (also ADC-C input 8, PGA-4 optional output filter and CMPSS-4 input); keep the ADC input below VDDA + 0.3 V. |
| 25 | A10/B1/C10/PGA7_OF | input | ADC-A input 10 (also ADC-B input 1, ADC-C input 10 and PGA-7 optional output filter); keep the ADC input below VDDA + 0.3 V. |
| 26 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 27 | VDD | power_in | 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins. |
| 28 | VDDIO | power_in | 3.3 V digital I/O supply; place a minimum 0.1 µF decoupling capacitor on each VDDIO pin. |
| 29 | GPIO13 | bidirectional | General-purpose I/O 13 (default GPIO), multiplexed with EPWM7_B, CANB_RX, EQEP1_INDEX, SCIB_RX, PMBUSA_ALERT and FSIRXA_CLK. |
| 30 | GPIO12 | bidirectional | General-purpose I/O 12 (default GPIO), multiplexed with EPWM7_A, CANB_TX, EQEP1_STROBE, SCIB_TX, PMBUSA_CTL and FSIRXA_D0. |
| 31 | GPIO11 | bidirectional | General-purpose I/O 11 (default GPIO), multiplexed with EPWM6_B, SCIB_RX, OUTPUTXBAR7, EQEP1_B, SPIA_STE and FSIRXA_D1. |
| 32 | GPIO33 | bidirectional | General-purpose I/O 33 (default GPIO), multiplexed with I2CA_SCL, SPIB_STE, OUTPUTXBAR4, LINA_RX, SD1_C3, FSIRXA_CLK and CANA_RX. |
| 33 | GPIO16 | bidirectional | General-purpose I/O 16 (default GPIO), multiplexed with SPIA_SIMO, CANB_TX, OUTPUTXBAR7, EPWM5_A, SCIA_TX, SD1_D1, EQEP1_STROBE, PMBUSA_SCL and XCLKOUT. |
| 34 | GPIO17 | bidirectional | General-purpose I/O 17 (default GPIO), multiplexed with SPIA_SOMI, CANB_RX, OUTPUTXBAR8, EPWM5_B, SCIA_RX, SD1_C1, EQEP1_INDEX and PMBUSA_SDA. |
| 35 | GPIO24 | bidirectional | General-purpose I/O 24 (default GPIO), multiplexed with OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SD1_D1, PMBUSA_SCL, SCIA_TX and ERRORSTS. |
| 36 | TCK | input | JTAG test clock input with internal pullup. |
| 37 | GPIO37/TDO | output | JTAG test data output (TDO, default function); the pin is tri-stated when there is no JTAG activity, so an internal or external pullup is required to avoid a floating GPIO input. |
| 38 | TMS | bidirectional | JTAG test mode select with internal pullup, clocked on TCK rising edge; a 2.2 kΩ external pullup to VDDIO is recommended on the board. |
| 39 | GPIO35/TDI | input | JTAG test data input (TDI, default function); enable the internal pullup or add an external pullup to avoid a floating input. |
| 40 | GPIO32 | bidirectional | General-purpose I/O 32 (default GPIO), multiplexed with I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3, FSIRXA_D0 and CANA_TX. |
| 41 | GPIO18_X2 | bidirectional | General-purpose I/O 18 also serving as the X2 crystal oscillator output; GPIO18 and its mux options are usable only when INTOSC clocks the system and X1 has an external pull-down (1 kΩ recommended). |
| 42 | X1 | bidirectional | Crystal oscillator or single-ended 3.3 V clock input; device initialization software must configure this pin before enabling the crystal oscillator. |
| 43 | VDDIO | power_in | 3.3 V digital I/O supply; place a minimum 0.1 µF decoupling capacitor on each VDDIO pin. |
| 44 | VDD | power_in | 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins. |
| 45 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 46 | VREGENZ | input | Internal regulator enable with internal pulldown; tie to VSS to enable the internal VREG and to VDDIO to use an external VDD supply. |
| 47 | GPIO8 | bidirectional | General-purpose I/O 8 (default GPIO), multiplexed with EPWM5_A, CANB_TX, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL and FSITXA_D1. |
| 48 | GPIO4 | bidirectional | General-purpose I/O 4 (default GPIO), multiplexed with EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK. |
| 49 | GPIO3 | bidirectional | General-purpose I/O 3 (default GPIO), multiplexed with EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and FSIRXA_D0. |
| 50 | GPIO2 | bidirectional | General-purpose I/O 2 (default GPIO), multiplexed with EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SCIA_TX and FSIRXA_D1. |
| 51 | GPIO1 | bidirectional | General-purpose I/O 1 (default GPIO), multiplexed with EPWM1_B and I2CA_SCL. |
| 52 | GPIO0 | bidirectional | General-purpose I/O 0 (default GPIO), multiplexed with EPWM1_A and I2CA_SDA. |
| 53 | VDDIO_SW | power_in | 3.3 V supply for the internal DC/DC regulator; if the DC/DC is used a 20 µF bulk input capacitor is required, and this pin must be tied to VDDIO. |
| 54 | GPIO23_VSW | bidirectional | General-purpose I/O 23 (default DC/DC mode) that serves as the internal DC/DC switching output VSW when DCDCEN = 1; it has about 100 pF internal capacitance, so an alternate GPIO is recommended where fast switching response is needed. |
| 55 | VSS_SW | power_in | Internal DC/DC regulator ground; must be tied to VSS. |
| 56 | GPIO22_VFBSW | bidirectional | General-purpose I/O 22 (default DC/DC mode) that serves as the internal DC/DC feedback VFBSW when DCDCEN = 1; connect it to the node where L(VSW) meets the VDD rail, as close to the device as possible. |
| 57 | GPIO7 | bidirectional | General-purpose I/O 7 (default GPIO), multiplexed with EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK. |
| 58 | VSS | power_in | Digital ground; all VSS pins must be connected to the board ground. |
| 59 | VDD | power_in | 1.2 V digital logic supply; TI recommends a minimum total capacitance of about 20 µF near the VDD pins. |
| 60 | VDDIO | power_in | 3.3 V digital I/O supply; place a minimum 0.1 µF decoupling capacitor on each VDDIO pin. |
| 61 | GPIO5 | bidirectional | General-purpose I/O 5 (default GPIO), multiplexed with EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1. |
| 62 | GPIO9 | bidirectional | General-purpose I/O 9 (default GPIO), multiplexed with EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX, SPIA_CLK and FSITXA_D0. |
| 63 | GPIO10 | bidirectional | General-purpose I/O 10 (default GPIO), multiplexed with EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI, I2CA_SDA and FSITXA_CLK. |
| 64 | GPIO6 | bidirectional | General-purpose I/O 6 (default GPIO), multiplexed with EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VDDIO 以 VSS 为基准 (供电电压,绝对最大额定值) | VDDIO | -0.3 | | 4.6 | V | 以 VSS 为基准 | 58 |
| VDDA 以 VSSA 为基准 (供电电压,绝对最大额定值) | VDDA | -0.3 | | 4.6 | V | 以 VSSA 为基准 | 58 |
| VDD 以 VSS 为基准 (内核供电电压,绝对最大额定值) | VDD | -0.3 | | 1.5 | V | 以 VSS 为基准 | 58 |
| VDDIO 和 VDDIO_SW 引脚之间的电压差 | | -0.3 | | 0.3 | V | | 58 |
| 输入电压 VIN (3.3V) | VIN | -0.3 | | 4.6 | V | | 58 |
| 输出电压 | VO | -0.3 | | 4.6 | V | | 58 |
| 数字输入钳位电流(每引脚) | IIK | -20 | | 20 | mA | VIN < VSS 或 VIN > VDDIO | 58 |
| 模拟输入钳位电流(每引脚) | IIKANALOG | -20 | | 20 | mA | VIN < VSSA 或 VIN > VDDA | 58 |
| 所有输入的总计钳位电流 | IIKTOTAL | -20 | | 20 | mA | VIN < VSS/VSSA 或 VIN > VDDIO/VDDA | 58 |
| 数字输出电流(每引脚) | IOUT | -20 | | 20 | mA | | 58 |
| 自然通风温度 | TA | -40 | | 125 | °C | 自然通风 | 58 |
| 工作结温 | TJ | -40 | | 150 | °C | | 58 |
| 贮存温度 | Tstg | -65 | | 150 | °C | | 58 |
| 器件电源电压 VDDIO 和 VDDA(启用内部 BOR) | VDDIO, VDDA | | 3.3 | 3.63 | V | 启用内部 BOR | 59 |
| 器件电源电压 VDDIO 和 VDDA(禁用内部 BOR) | VDDIO, VDDA | 2.8 | 3.3 | 3.63 | V | 禁用内部 BOR | 59 |
| 器件电源电压 VDD | VDD | 1.14 | 1.2 | 1.32 | V | | 59 |
| VDDIO 电源斜坡时间 | tVDDIO-RAMP | 10 | | | ms | 从 1V 到 VBOR-VDDIO(MAX) | 59 |
| 结温 TJ(S 版本) | TJ | -40 | | 125 | °C | S 版本 | 59 |
| VDD 运行期间的电流消耗(外部电源) | IDD | | 61 | 90 | mA | 请参阅节 6.5.4 | 61 |
| VDDIO 运行期间的电流消耗(外部电源) | IDDIO | | 26 | 45 | mA | | 61 |
| VDDA 运行期间的电流消耗(外部电源) | IDDA | | 12 | 30 | mA | | 61 |
| 器件处于空闲模式时的 VDD 电流消耗 | IDD | | 18 | 40 | mA | CPU 处于空闲模式;闪存被断电;XCLKOUT 被关闭 | 61 |
| 器件处于空闲模式时的 VDDIO 电流消耗 | IDDIO | | 1.2 | 4 | mA | | 61 |
| 器件处于空闲模式时的 VDDA 电流消耗 | IDDA | | 0.9 | 1.2 | mA | | 61 |
| 器件处于停机模式时的 VDD 电流消耗 | IDD | | 0.9 | 20 | mA | CPU 处于停机模式;闪存被断电;XCLKOUT 被关闭 | 61 |
| 器件处于停机模式时的 VDDIO 电流消耗 | IDDIO | | 0.8 | 4 | mA | | 61 |
| 器件处于停机模式时的 VDDA 电流消耗 | IDDA | | 0.2 | 0.5 | mA | | 61 |
| 擦除/编程周期期间的 VDD 电流消耗 | IDD | | 40 | 70 | mA | CPU 从闪存运行擦除/编程;禁用 VREG;SYSCLK 100MHz | 61 |
| 擦除/编程周期期间的 VDDIO 电流消耗 | IDDIO | | 33 | 75 | mA | | 61 |
| 擦除/编程周期期间的 VDDA 电流消耗 | IDDA | | 0.1 | 2.5 | mA | | 61 |
| VDDIO 运行期间的电流消耗(内部 VREG) | IDDIO | | 86 | 113 | mA | 请参阅节 6.5.4 | 61 |
| VDDA 运行期间的电流消耗(内部 VREG) | IDDA | | 12 | 30 | mA | | 61 |
| 低电平输出电压 (IOL=IOL 最大值) | VOL | | | 0.4 | V | IOL=IOL 最大值 | 67 |
| 低电平输出电压 (IOL=100µA) | VOL | | | 0.2 | V | IOL = 100µA | 67 |
| 高电平输入电压 (3.3V) | VIH | 2 | | | V | | 67 |
| 低电平输入电压 (3.3V) | VIL | | | 0.8 | V | | 67 |
| VDDIO 欠压复位电压 | VBOR-VDDIO | 2.81 | | 3 | V | | 67 |
| 内部稳压器输出 | VVREG | 1.14 | 1.2 | 1.32 | V | | 80 |
| 斜降时的 VDDIO 欠压复位电压 | VBOR-VDDIO-DN | 2.81 | | 3 | V | XRSn 释放之后 | 80 |
| CL1、CL2 负载电容 | CL1, CL2 | 12 | | 24 | pF | | 93 |
| 晶振并联电容 | C0 | | | 7 | pF | | 93 |
| fINTOSC 频率,INTOSC1 和 INTOSC2 | fINTOSC | 9.7 | 10 | 10.3 | MHz | | 94 |
| 室温下的频率稳定性 | fINTOSC-STABILITY | -0.1 | | 0.1 | % | 30°C,标称 VDD | 95 |
| VDD 上的频率稳定性 | fINTOSC-STABILITY | -0.2 | | 0.2 | % | 30°C | 95 |
| 频率稳定性 | fINTOSC-STABILITY | -3 | | 3 | % | | 95 |
| ADCCLK(源自 PERx.SYSCLK) | ADCCLK | 5 | | 50 | MHz | | 123 |
| 有效输出电压范围 VOUT (RL=5kΩ) | VOUT | 0.3 | | | V | RL = 5kΩ | 136 |
| 有效输出电压范围 VOUT (RL=1kΩ) | VOUT | 0.6 | | | V | RL = 1kΩ | 136 |
| 负载调整率 | | -1 | | 1 | mV/V | | 136 |
| 偏移量误差 | | -10 | | 10 | mV | 中点 | 136 |
| 增益误差 | | -2.5 | | 2.5 | FSR 百分比 | | 136 |
| 比较器输入 (CMPINxx) 范围 | | 0 | | | V | | 143 |
| 以输入为基准的偏移量误差 | | -20 | | 20 | mV | 低共模,反相输入设置为 50mV | 143 |
| CMPSS DAC 静态偏移量误差 | | -25 | | 25 | mV | | 144 |
| CMPSS DAC 静态增益误差 | | -2 | | 2 | FSR 百分比 | | 144 |
| CMPSS DAC 静态 INL | INL | -16 | | 16 | LSB | 已更正端点 | 144 |
| CMPSS DAC 输出干扰 | | -100 | | 100 | LSB | 由同一 CMPSS 模块内的比较器跳闸或 CMPSS DAC 代码更改引起的误差 | 144 |
| VDAC 负载 | | 6 | 8 | 10 | kΩ | 当 VDAC 为基准时 | 144 |
| VBOR-GB VDDIO BOR 保护频带 | VBOR-GB | | 0.1 | | V | | 59 |
## CAD (KiCad official)
- Symbol: `F280049CPMS`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `f280049cpms-etched.step` / `f280049cpms-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `f280049cpms.step` / `f280049cpms.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/cn/lit/gpn/tms320f280049) (277 pp, sha256 `867e7bb5ada6819c`, retrieved 2026-11-10, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/f280049cpms-datasheet.pdf)