component
F280040CPMQR
Public Made by Adomby adom
Texas Instruments Microcontroller Units (MCUs/MPUs/SOCs), QFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
dd50b7e
F280040CPMQR
Texas Instruments · Microcontroller Units (MCUs/MPUs/SOCs) · QFP-64(10x10)
F280040CPMQR from Texas Instruments, in a QFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 with mux options SCIA_TX, EPWM7_B, OUTPUTXBAR6, EQEP1_B, SD1_C3, EQEP2_INDEX, LINA_RX, SPIB_STE and ERRORSTS. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 with mux options SCIA_RX, EPWM7_A, OUTPUTXBAR5, EQEP1_A, SD1_D3, EQEP2_STROBE, LINA_TX, SPIB_CLK and ERRORSTS. |
| 3 | XRSn | bidirectional | Device reset input and watchdog reset open-drain output with internal pull-up; place a 2.2k-10k resistor to VDDIO and at most 100nF to VSS. |
| 4 | VDD | power_in | 1.2V digital logic supply; about 20uF total decoupling near the VDD pins is recommended. |
| 5 | VSS | power_in | Digital ground; must be connected to board ground. |
| 6 | A6/PGA5_OF | input | ADC-A input 6, PGA-5 filtered output (optional), CMPSS-5 inputs and AIO228 digital input. |
| 7 | B2/C6/PGA3_OF | input | ADC-B input 2, ADC-C input 6, PGA-3 filtered output (optional), CMPSS-3 inputs and AIO226 digital input. |
| 8 | B3/VDAC | input | ADC-B input 3 or optional external reference for the on-chip DAC; has a non-disableable 100pF capacitor to VSSA, and at least 1uF is required when used as DAC reference. |
| 9 | A2/B6/PGA1_OF | input | ADC-A input 2, ADC-B input 6, PGA-1 filtered output (optional), CMPSS-1 inputs and AIO224 digital input. |
| 10 | PGA1_GND,PGA3_GND,PGA5_GND | power_in | Kelvin ground reference shared by PGA-1, PGA-3 and PGA-5; tie to VSSA if unused. |
| 11 | C4/PGA5_IN | input | ADC-C input 4 and PGA-5 input, with CMPSS-5 inputs and AIO239 digital input. |
| 12 | C0/PGA1_IN | input | ADC-C input 0 and PGA-1 input, with CMPSS-1 inputs and AIO237 digital input. |
| 13 | C2/PGA3_IN | input | ADC-C input 2 and PGA-3 input, with CMPSS-3 inputs and AIO244 digital input. |
| 14 | A1/DACB_OUT | bidirectional | ADC-A input 1, buffered DAC-B output and AIO232 digital input. |
| 15 | A0/B15/C15/DACA_OUT | bidirectional | ADC-A input 0, ADC-B input 15, ADC-C input 15, buffered DAC-A output and AIO231 digital input. |
| 16 | VREFHIA,VREFHIB,VREFHIC | bidirectional | ADC-A/B/C high reference voltage, externally driven or device-driven; place at least 2.2uF to the VREFLO pin and do not load externally. |
| 17 | VREFLOA,VREFLOB,VREFLOC | input | ADC-A/B/C low reference voltage; tie to VSSA. |
| 18 | C1/PGA2_IN | input | ADC-C input 1 and PGA-2 input, with CMPSS-2 inputs and AIO238 digital input. |
| 19 | C3/PGA4_IN | input | ADC-C input 3 and PGA-4 input, with CMPSS-4 inputs and AIO245 digital input. |
| 20 | PGA2_GND,PGA4_GND,PGA6_GND | power_in | Kelvin ground reference shared by PGA-2, PGA-4 and PGA-6; tie to VSSA if unused. |
| 21 | VSSA | power_in | Analog ground. |
| 22 | VDDA | power_in | 3.3V analog supply; place at least 2.2uF decoupling to VSSA. |
| 23 | A4/B8/PGA2_OF | input | ADC-A input 4, ADC-B input 8, PGA-2 filtered output (optional), CMPSS-2 inputs and AIO225 digital input. |
| 24 | B4/C8/PGA4_OF | input | ADC-B input 4, ADC-C input 8, PGA-4 filtered output (optional), CMPSS-4 inputs and AIO227 digital input. |
| 25 | A10/B1/C10/PGA7_OF | input | ADC-A input 10, ADC-B input 1, ADC-C input 10, PGA-7 filtered output, CMPSS-7 inputs and AIO230 digital input. |
| 26 | VSS | power_in | Digital ground; must be connected to board ground. |
| 27 | VDD | power_in | 1.2V digital logic supply; about 20uF total decoupling near the VDD pins is recommended. |
| 28 | VDDIO | power_in | 3.3V digital I/O supply; place at least 0.1uF decoupling on each pin. |
| 29 | FLT2 | unconnected | Flash test pin 2 reserved for TI; must be left unconnected (on PMQ this location is not GPIO13). |
| 30 | FLT1 | unconnected | Flash test pin 1 reserved for TI; must be left unconnected (on PMQ this location is not GPIO12). |
| 31 | GPIO11 | bidirectional | General-purpose I/O 11 with mux options EPWM6_B, SCIB_RX, OUTPUTXBAR7, EQEP1_B, SPIA_STE and FSIRXA_D1. |
| 32 | GPIO33 | bidirectional | General-purpose I/O 33 with mux options I2CA_SCL, SPIB_STE, OUTPUTXBAR4, LINA_RX, SD1_C3, FSIRXA_CLK and CANA_RX. |
| 33 | GPIO16 | bidirectional | General-purpose I/O 16 with mux options SPIA_SIMO, CANB_TX, OUTPUTXBAR7, EPWM5_A, SCIA_TX, SD1_D1, EQEP1_STROBE, PMBUSA_SCL and XCLKOUT. |
| 34 | GPIO17 | bidirectional | General-purpose I/O 17 with mux options SPIA_SOMI, CANB_RX, OUTPUTXBAR8, EPWM5_B, SCIA_RX, SD1_C1, EQEP1_INDEX and PMBUSA_SDA. |
| 35 | GPIO24 | bidirectional | General-purpose I/O 24 with mux options OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SD1_D1, PMBUSA_SCL, SCIA_TX and active-low ERRORSTS. |
| 36 | TCK | input | JTAG test clock with internal pull-up. |
| 37 | GPIO37/TDO | bidirectional | General-purpose I/O 37, default JTAG TDO (tri-stated when no JTAG activity); enable internal pull-up or add external pull-up. |
| 38 | TMS | bidirectional | JTAG test mode select with internal pull-up; add an external pull-up (2.2k recommended) to VDDIO; no TRSTn pin exists. |
| 39 | GPIO35/TDI | bidirectional | General-purpose I/O 35, default JTAG TDI; enable internal pull-up or add external pull-up to avoid a floating input. |
| 40 | GPIO32 | bidirectional | General-purpose I/O 32 with mux options I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3, FSIRXA_D0 and CANA_TX. |
| 41 | GPIO18_X2 | bidirectional | General-purpose I/O 18 or crystal oscillator output X2; GPIO usable only when clocked by INTOSC with X1 pulled down (1k recommended). |
| 42 | X1 | bidirectional | Crystal oscillator or single-ended 3.3V clock input; tie to VSS if unused. |
| 43 | VDDIO | power_in | 3.3V digital I/O supply; place at least 0.1uF decoupling on each pin. |
| 44 | VDD | power_in | 1.2V digital logic supply; about 20uF total decoupling near the VDD pins is recommended. |
| 45 | VSS | power_in | Digital ground; must be connected to board ground. |
| 46 | VREGENZ | input | Internal regulator enable with internal pull-down; tie to VSS to enable internal VREG, or to VDDIO to use an external supply. |
| 47 | GPIO8 | bidirectional | General-purpose I/O 8 with mux options EPWM5_A, CANB_TX, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL and FSITXA_D1. |
| 48 | GPIO4 | bidirectional | General-purpose I/O 4 with mux options EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK. |
| 49 | GPIO3 | bidirectional | General-purpose I/O 3 with mux options EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and FSIRXA_D0. |
| 50 | GPIO2 | bidirectional | General-purpose I/O 2 with mux options EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SCIA_TX and FSIRXA_D1. |
| 51 | GPIO1 | bidirectional | General-purpose I/O 1 with mux options EPWM1_B and I2CA_SCL. |
| 52 | GPIO0 | bidirectional | General-purpose I/O 0 with mux options EPWM1_A and I2CA_SDA. |
| 53 | VDDIO_SW | power_in | 3.3V supply for the internal DC-DC regulator; needs 20uF bulk input capacitance when used and must be connected to VDDIO. |
| 54 | GPIO23_VSW | bidirectional | GPIO23 or internal DC-DC switch output VSW (DC-DC mode by default); about 100pF internal capacitance. |
| 55 | VSS_SW | power_in | Internal DC-DC regulator ground; must be connected to VSS. |
| 56 | GPIO22_VFBSW | bidirectional | GPIO22 or internal DC-DC feedback VFBSW (DC-DC mode by default); connect to the node where L(VSW) meets the VDD rail when DC-DC is used. |
| 57 | GPIO7 | bidirectional | General-purpose I/O 7 with mux options EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK. |
| 58 | VSS | power_in | Digital ground; must be connected to board ground. |
| 59 | VDD | power_in | 1.2V digital logic supply; about 20uF total decoupling near the VDD pins is recommended. |
| 60 | VDDIO | power_in | 3.3V digital I/O supply; place at least 0.1uF decoupling on each pin. |
| 61 | GPIO5 | bidirectional | General-purpose I/O 5 with mux options EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1. |
| 62 | GPIO9 | bidirectional | General-purpose I/O 9 with mux options EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX, SPIA_CLK and FSITXA_D0. |
| 63 | GPIO10 | bidirectional | General-purpose I/O 10 with mux options EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI, I2CA_SDA and FSITXA_CLK. |
| 64 | GPIO6 | bidirectional | General-purpose I/O 6 with mux options EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | QFP-64(10x10) |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDDIO | VDDIO | -0.3 | 4.6 | V | 以 VSS 为基准 | 59 | |
| Supply voltage VDDA | VDDA | -0.3 | 4.6 | V | 以 VSSA 为基准 | 59 | |
| Supply voltage VDD | VDD | -0.3 | 1.5 | V | 以 VSS 为基准 | 59 | |
| Voltage difference between VDDIO and VDDIO_SW pins | -0.3 | 0.3 | V | VDDIO 和 VDDIO_SW 引脚之间的电压差 | 59 | ||
| Input voltage | VIN | -0.3 | 4.6 | V | (3.3V) | 59 | |
| Output voltage | VO | -0.3 | 4.6 | V | 59 | ||
| Digital input clamp current (per pin) | IIK | -20 | 20 | mA | 数字输入(每引脚), VIN < VSS 或 VIN > VDDIO | 59 | |
| Analog input clamp current (per pin) | IIKANALOG | -20 | 20 | mA | 模拟输入(每引脚), VIN < VSSA 或 VIN > VDDA | 59 | |
| Total input clamp current (all inputs) | IIKTOTAL | -20 | 20 | mA | 所有输入的总计 | 59 | |
| Digital output current (per pin) | IOUT | -20 | 20 | mA | 数字输出(每引脚) | 59 | |
| Natural ventilation temperature | TA | -40 | 125 | °C | 自然通风 | 59 | |
| Operating junction temperature | TJ | -40 | 150 | °C | 工作结温 | 59 | |
| Storage temperature | Tstg | -65 | 150 | °C | 贮存温度 | 59 | |
| Device supply voltage VDDIO and VDDA, internal BOR enabled | VDDIO, VDDA | 3.3 | 3.63 | V | 启用内部 BOR(最小值为公式 VBOR-VDDIO(MAX)+VBOR-GB) | 60 | |
| Device supply voltage VDDIO and VDDA, internal BOR disabled | VDDIO, VDDA | 2.8 | 3.3 | 3.63 | V | 禁用内部 BOR | 60 |
| Device supply voltage VDD | VDD | 1.14 | 1.2 | 1.32 | V | 60 | |
| Natural ventilation temperature (Q version, AEC Q100 qualified) | TA | -40 | 125 | °C | Q 版本(AEC Q100 认证) | 60 | |
| Operating current IDD during operation | IDD | 61 | 90 | mA | 运行期间的 VDD 电流消耗,请参阅节 7.5.4 | 62 | |
| Operating current IDDIO during operation | IDDIO | 26 | 45 | mA | 运行期间的 VDDIO 电流消耗,请参阅节 7.5.4 | 62 | |
| Operating current IDDA during operation | IDDA | 12 | 30 | mA | 运行期间的 VDDA 电流消耗,请参阅节 7.5.4 | 62 | |
| Idle mode current IDD | IDD | 18 | 40 | mA | 空闲模式:CPU 处于空闲模式,闪存被断电,XCLKOUT 被关闭 | 62 | |
| Idle mode current IDDIO | IDDIO | 1.2 | 4 | mA | 空闲模式 | 62 | |
| Idle mode current IDDA | IDDA | 0.9 | 1.2 | mA | 空闲模式 | 62 | |
| Halt mode current IDD | IDD | 0.9 | 20 | mA | 停机模式:CPU 处于停机模式,闪存被断电,XCLKOUT 被关闭 | 62 | |
| Halt mode current IDDIO | IDDIO | 0.8 | 4 | mA | 停机模式 | 62 | |
| Halt mode current IDDA | IDDA | 0.2 | 0.5 | mA | 停机模式 | 62 | |
| Flash erase/program current IDD | IDD | 40 | 70 | mA | 擦除/编程周期期间,SYSCLK 为 100MHz,禁用 VREG | 62 | |
| Flash erase/program current IDDIO | IDDIO | 33 | 75 | mA | 擦除/编程周期期间 | 62 | |
| Flash erase/program current IDDA | IDDA | 0.1 | 2.5 | mA | 擦除/编程周期期间 | 62 | |
| Low-level output voltage | VOL | 0.4 | V | IOL=IOL 最大值 | 68 | ||
| Low-level output voltage | VOL | 0.2 | V | IOL = 100µA | 68 | ||
| High-level output source current, all output pins | IOH | -4 | mA | 所有输出引脚的高电平输出源电流 | 68 | ||
| Low-level output sink current, all output pins | IOL | 4 | mA | 所有输出引脚的低电平输出灌电流 | 68 | ||
| High-level output impedance, all output pins | ROH | 70 | Ω | 所有输出引脚的高电平输出阻抗 | 68 | ||
| Low-level output impedance, all output pins | ROL | 70 | Ω | 所有输出引脚的低电平输出阻抗 | 68 | ||
| High-level input voltage | VIH | 2 | V | (3.3V),max 为公式 VDDIO+0.3 | 68 | ||
| Low-level input voltage | VIL | 0.8 | V | (3.3V),min 为公式 VSS-0.3 | 68 | ||
| Input hysteresis | VHYSTERESIS | 150 | mV | 输入迟滞 | 68 | ||
| Input current with pulldown | IPULLDOWN | 100 | µA | 带下拉的输入;VDDIO = 3.3V,VIN = VDDIO | 68 | ||
| Input current with pullup, digital input | IPULLUP | 160 | µA | 启用上拉的数字输入;VDDIO = 3.3V,VIN = 0V | 68 | ||
| Input current with pullup, analog input | IPULLUP | 160 | µA | 启用上拉的模拟输入;VDDA = 3.3V,VIN = 0V | 68 | ||
| Pin leakage current, GPIO excluding GPIO23_VSW | ILEAK | 2 | µA | 除 GPIO23_VSW 外的所有 GPIO 上拉和输出被禁用;0V ≤ VIN ≤ VDDIO | 68 | ||
| Pin leakage current, GPIO23_VSW | ILEAK | 45 | µA | 0V ≤ VIN ≤ VDDIO | 68 | ||
| Pin leakage current, analog pins (excluding ADCINB3/VDAC and PGAx_OF) | ILEAK | 0.1 | µA | 模拟驱动器禁用;0V ≤ VIN ≤ VDDA | 68 | ||
| Input capacitance, digital GPIO excluding GPIO23_VSW | CI | 2 | pF | 除 GPIO23_VSW 外的所有数字 GPIO | 68 | ||
| VDDIO power-on reset voltage | VPOR-VDDIO | 2.3 | V | VDDIO 上电复位电压 | 68 | ||
| VDDIO brown-out reset voltage | VBOR-VDDIO | 2.81 | 3 | V | VDDIO 欠压复位电压 | 68 | |
| Internal regulator output | VVREG | 1.2 | V | 内部 VREG 打开 | 68 | ||
| Crystal oscillator load capacitance | CL1, CL2 | 12 | 24 | pF | 晶体振荡器负载电容 | 94 | |
| Crystal shunt capacitance | C0 | 7 | pF | 晶振并联电容 | 94 | ||
| INTOSC1 and INTOSC2 frequency | fINTOSC | 9.7 | 10 | 10.3 | MHz | INTOSC1 和 INTOSC2 | 95 |
| INTOSC frequency stability at room temperature | fINTOSC-STABILITY | -0.1 | 0.1 | % | 30°C,标称 VDD | 96 | |
| INTOSC frequency stability over VDD | fINTOSC-STABILITY | -0.2 | 0.2 | % | VDD 上的频率稳定性,30°C | 96 | |
| INTOSC frequency stability over temperature | fINTOSC-STABILITY | -3 | 3 | % | 频率稳定性 | 96 | |
| ESD human body model (HBM), all pins | V(ESD) | -2000 | 2000 | V | 64 引脚 PM 封装,Q 温度范围,符合 AEC Q100-002,所有引脚 | 60 | |
| ESD charged device model (CDM), all pins | V(ESD) | -500 | 500 | V | 64 引脚 PM 封装,Q 温度范围,符合 AEC Q100-011,所有引脚 | 60 | |
| ESD charged device model (CDM), corner pins | V(ESD) | -750 | 750 | V | 64 引脚 PM 上的转角引脚 1、16、17、32、33、48、49、64 | 60 |
CAD (KiCad official)
- Symbol:
F280040CPMQR - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: QFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
f280040cpmqr-etched.step/f280040cpmqr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280040cpmqr.step/f280040cpmqr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (270 pp, sha256
f0eccdafc7ec75fa, retrieved 2026-11-10, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# F280040CPMQR
**Texas Instruments** · Microcontroller Units (MCUs/MPUs/SOCs) · QFP-64(10x10)
F280040CPMQR from Texas Instruments, in a QFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O 29 with mux options SCIA_TX, EPWM7_B, OUTPUTXBAR6, EQEP1_B, SD1_C3, EQEP2_INDEX, LINA_RX, SPIB_STE and ERRORSTS. |
| 2 | GPIO28 | bidirectional | General-purpose I/O 28 with mux options SCIA_RX, EPWM7_A, OUTPUTXBAR5, EQEP1_A, SD1_D3, EQEP2_STROBE, LINA_TX, SPIB_CLK and ERRORSTS. |
| 3 | XRSn | bidirectional | Device reset input and watchdog reset open-drain output with internal pull-up; place a 2.2k-10k resistor to VDDIO and at most 100nF to VSS. |
| 4 | VDD | power_in | 1.2V digital logic supply; about 20uF total decoupling near the VDD pins is recommended. |
| 5 | VSS | power_in | Digital ground; must be connected to board ground. |
| 6 | A6/PGA5_OF | input | ADC-A input 6, PGA-5 filtered output (optional), CMPSS-5 inputs and AIO228 digital input. |
| 7 | B2/C6/PGA3_OF | input | ADC-B input 2, ADC-C input 6, PGA-3 filtered output (optional), CMPSS-3 inputs and AIO226 digital input. |
| 8 | B3/VDAC | input | ADC-B input 3 or optional external reference for the on-chip DAC; has a non-disableable 100pF capacitor to VSSA, and at least 1uF is required when used as DAC reference. |
| 9 | A2/B6/PGA1_OF | input | ADC-A input 2, ADC-B input 6, PGA-1 filtered output (optional), CMPSS-1 inputs and AIO224 digital input. |
| 10 | PGA1_GND,PGA3_GND,PGA5_GND | power_in | Kelvin ground reference shared by PGA-1, PGA-3 and PGA-5; tie to VSSA if unused. |
| 11 | C4/PGA5_IN | input | ADC-C input 4 and PGA-5 input, with CMPSS-5 inputs and AIO239 digital input. |
| 12 | C0/PGA1_IN | input | ADC-C input 0 and PGA-1 input, with CMPSS-1 inputs and AIO237 digital input. |
| 13 | C2/PGA3_IN | input | ADC-C input 2 and PGA-3 input, with CMPSS-3 inputs and AIO244 digital input. |
| 14 | A1/DACB_OUT | bidirectional | ADC-A input 1, buffered DAC-B output and AIO232 digital input. |
| 15 | A0/B15/C15/DACA_OUT | bidirectional | ADC-A input 0, ADC-B input 15, ADC-C input 15, buffered DAC-A output and AIO231 digital input. |
| 16 | VREFHIA,VREFHIB,VREFHIC | bidirectional | ADC-A/B/C high reference voltage, externally driven or device-driven; place at least 2.2uF to the VREFLO pin and do not load externally. |
| 17 | VREFLOA,VREFLOB,VREFLOC | input | ADC-A/B/C low reference voltage; tie to VSSA. |
| 18 | C1/PGA2_IN | input | ADC-C input 1 and PGA-2 input, with CMPSS-2 inputs and AIO238 digital input. |
| 19 | C3/PGA4_IN | input | ADC-C input 3 and PGA-4 input, with CMPSS-4 inputs and AIO245 digital input. |
| 20 | PGA2_GND,PGA4_GND,PGA6_GND | power_in | Kelvin ground reference shared by PGA-2, PGA-4 and PGA-6; tie to VSSA if unused. |
| 21 | VSSA | power_in | Analog ground. |
| 22 | VDDA | power_in | 3.3V analog supply; place at least 2.2uF decoupling to VSSA. |
| 23 | A4/B8/PGA2_OF | input | ADC-A input 4, ADC-B input 8, PGA-2 filtered output (optional), CMPSS-2 inputs and AIO225 digital input. |
| 24 | B4/C8/PGA4_OF | input | ADC-B input 4, ADC-C input 8, PGA-4 filtered output (optional), CMPSS-4 inputs and AIO227 digital input. |
| 25 | A10/B1/C10/PGA7_OF | input | ADC-A input 10, ADC-B input 1, ADC-C input 10, PGA-7 filtered output, CMPSS-7 inputs and AIO230 digital input. |
| 26 | VSS | power_in | Digital ground; must be connected to board ground. |
| 27 | VDD | power_in | 1.2V digital logic supply; about 20uF total decoupling near the VDD pins is recommended. |
| 28 | VDDIO | power_in | 3.3V digital I/O supply; place at least 0.1uF decoupling on each pin. |
| 29 | FLT2 | unconnected | Flash test pin 2 reserved for TI; must be left unconnected (on PMQ this location is not GPIO13). |
| 30 | FLT1 | unconnected | Flash test pin 1 reserved for TI; must be left unconnected (on PMQ this location is not GPIO12). |
| 31 | GPIO11 | bidirectional | General-purpose I/O 11 with mux options EPWM6_B, SCIB_RX, OUTPUTXBAR7, EQEP1_B, SPIA_STE and FSIRXA_D1. |
| 32 | GPIO33 | bidirectional | General-purpose I/O 33 with mux options I2CA_SCL, SPIB_STE, OUTPUTXBAR4, LINA_RX, SD1_C3, FSIRXA_CLK and CANA_RX. |
| 33 | GPIO16 | bidirectional | General-purpose I/O 16 with mux options SPIA_SIMO, CANB_TX, OUTPUTXBAR7, EPWM5_A, SCIA_TX, SD1_D1, EQEP1_STROBE, PMBUSA_SCL and XCLKOUT. |
| 34 | GPIO17 | bidirectional | General-purpose I/O 17 with mux options SPIA_SOMI, CANB_RX, OUTPUTXBAR8, EPWM5_B, SCIA_RX, SD1_C1, EQEP1_INDEX and PMBUSA_SDA. |
| 35 | GPIO24 | bidirectional | General-purpose I/O 24 with mux options OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SD1_D1, PMBUSA_SCL, SCIA_TX and active-low ERRORSTS. |
| 36 | TCK | input | JTAG test clock with internal pull-up. |
| 37 | GPIO37/TDO | bidirectional | General-purpose I/O 37, default JTAG TDO (tri-stated when no JTAG activity); enable internal pull-up or add external pull-up. |
| 38 | TMS | bidirectional | JTAG test mode select with internal pull-up; add an external pull-up (2.2k recommended) to VDDIO; no TRSTn pin exists. |
| 39 | GPIO35/TDI | bidirectional | General-purpose I/O 35, default JTAG TDI; enable internal pull-up or add external pull-up to avoid a floating input. |
| 40 | GPIO32 | bidirectional | General-purpose I/O 32 with mux options I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D3, FSIRXA_D0 and CANA_TX. |
| 41 | GPIO18_X2 | bidirectional | General-purpose I/O 18 or crystal oscillator output X2; GPIO usable only when clocked by INTOSC with X1 pulled down (1k recommended). |
| 42 | X1 | bidirectional | Crystal oscillator or single-ended 3.3V clock input; tie to VSS if unused. |
| 43 | VDDIO | power_in | 3.3V digital I/O supply; place at least 0.1uF decoupling on each pin. |
| 44 | VDD | power_in | 1.2V digital logic supply; about 20uF total decoupling near the VDD pins is recommended. |
| 45 | VSS | power_in | Digital ground; must be connected to board ground. |
| 46 | VREGENZ | input | Internal regulator enable with internal pull-down; tie to VSS to enable internal VREG, or to VDDIO to use an external supply. |
| 47 | GPIO8 | bidirectional | General-purpose I/O 8 with mux options EPWM5_A, CANB_TX, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL and FSITXA_D1. |
| 48 | GPIO4 | bidirectional | General-purpose I/O 4 with mux options EPWM3_A, OUTPUTXBAR3, CANA_TX and FSIRXA_CLK. |
| 49 | GPIO3 | bidirectional | General-purpose I/O 3 with mux options EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and FSIRXA_D0. |
| 50 | GPIO2 | bidirectional | General-purpose I/O 2 with mux options EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SCIA_TX and FSIRXA_D1. |
| 51 | GPIO1 | bidirectional | General-purpose I/O 1 with mux options EPWM1_B and I2CA_SCL. |
| 52 | GPIO0 | bidirectional | General-purpose I/O 0 with mux options EPWM1_A and I2CA_SDA. |
| 53 | VDDIO_SW | power_in | 3.3V supply for the internal DC-DC regulator; needs 20uF bulk input capacitance when used and must be connected to VDDIO. |
| 54 | GPIO23_VSW | bidirectional | GPIO23 or internal DC-DC switch output VSW (DC-DC mode by default); about 100pF internal capacitance. |
| 55 | VSS_SW | power_in | Internal DC-DC regulator ground; must be connected to VSS. |
| 56 | GPIO22_VFBSW | bidirectional | GPIO22 or internal DC-DC feedback VFBSW (DC-DC mode by default); connect to the node where L(VSW) meets the VDD rail when DC-DC is used. |
| 57 | GPIO7 | bidirectional | General-purpose I/O 7 with mux options EPWM4_B, OUTPUTXBAR5, EQEP1_B, CANB_RX, SPIB_SIMO and FSITXA_CLK. |
| 58 | VSS | power_in | Digital ground; must be connected to board ground. |
| 59 | VDD | power_in | 1.2V digital logic supply; about 20uF total decoupling near the VDD pins is recommended. |
| 60 | VDDIO | power_in | 3.3V digital I/O supply; place at least 0.1uF decoupling on each pin. |
| 61 | GPIO5 | bidirectional | General-purpose I/O 5 with mux options EPWM3_B, OUTPUTXBAR3, CANA_RX, SPIA_STE and FSITXA_D1. |
| 62 | GPIO9 | bidirectional | General-purpose I/O 9 with mux options EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX, SPIA_CLK and FSITXA_D0. |
| 63 | GPIO10 | bidirectional | General-purpose I/O 10 with mux options EPWM6_A, CANB_RX, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI, I2CA_SDA and FSITXA_CLK. |
| 64 | GPIO6 | bidirectional | General-purpose I/O 6 with mux options EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, CANB_TX, SPIB_SOMI and FSITXA_D0. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | QFP-64(10x10) |
| Category | Single Chip Microcomputer/Microcontroller |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VDDIO | VDDIO | -0.3 | | 4.6 | V | 以 VSS 为基准 | 59 |
| Supply voltage VDDA | VDDA | -0.3 | | 4.6 | V | 以 VSSA 为基准 | 59 |
| Supply voltage VDD | VDD | -0.3 | | 1.5 | V | 以 VSS 为基准 | 59 |
| Voltage difference between VDDIO and VDDIO_SW pins | | -0.3 | | 0.3 | V | VDDIO 和 VDDIO_SW 引脚之间的电压差 | 59 |
| Input voltage | VIN | -0.3 | | 4.6 | V | (3.3V) | 59 |
| Output voltage | VO | -0.3 | | 4.6 | V | | 59 |
| Digital input clamp current (per pin) | IIK | -20 | | 20 | mA | 数字输入(每引脚), VIN < VSS 或 VIN > VDDIO | 59 |
| Analog input clamp current (per pin) | IIKANALOG | -20 | | 20 | mA | 模拟输入(每引脚), VIN < VSSA 或 VIN > VDDA | 59 |
| Total input clamp current (all inputs) | IIKTOTAL | -20 | | 20 | mA | 所有输入的总计 | 59 |
| Digital output current (per pin) | IOUT | -20 | | 20 | mA | 数字输出(每引脚) | 59 |
| Natural ventilation temperature | TA | -40 | | 125 | °C | 自然通风 | 59 |
| Operating junction temperature | TJ | -40 | | 150 | °C | 工作结温 | 59 |
| Storage temperature | Tstg | -65 | | 150 | °C | 贮存温度 | 59 |
| Device supply voltage VDDIO and VDDA, internal BOR enabled | VDDIO, VDDA | | 3.3 | 3.63 | V | 启用内部 BOR(最小值为公式 VBOR-VDDIO(MAX)+VBOR-GB) | 60 |
| Device supply voltage VDDIO and VDDA, internal BOR disabled | VDDIO, VDDA | 2.8 | 3.3 | 3.63 | V | 禁用内部 BOR | 60 |
| Device supply voltage VDD | VDD | 1.14 | 1.2 | 1.32 | V | | 60 |
| Natural ventilation temperature (Q version, AEC Q100 qualified) | TA | -40 | | 125 | °C | Q 版本(AEC Q100 认证) | 60 |
| Operating current IDD during operation | IDD | | 61 | 90 | mA | 运行期间的 VDD 电流消耗,请参阅节 7.5.4 | 62 |
| Operating current IDDIO during operation | IDDIO | | 26 | 45 | mA | 运行期间的 VDDIO 电流消耗,请参阅节 7.5.4 | 62 |
| Operating current IDDA during operation | IDDA | | 12 | 30 | mA | 运行期间的 VDDA 电流消耗,请参阅节 7.5.4 | 62 |
| Idle mode current IDD | IDD | | 18 | 40 | mA | 空闲模式:CPU 处于空闲模式,闪存被断电,XCLKOUT 被关闭 | 62 |
| Idle mode current IDDIO | IDDIO | | 1.2 | 4 | mA | 空闲模式 | 62 |
| Idle mode current IDDA | IDDA | | 0.9 | 1.2 | mA | 空闲模式 | 62 |
| Halt mode current IDD | IDD | | 0.9 | 20 | mA | 停机模式:CPU 处于停机模式,闪存被断电,XCLKOUT 被关闭 | 62 |
| Halt mode current IDDIO | IDDIO | | 0.8 | 4 | mA | 停机模式 | 62 |
| Halt mode current IDDA | IDDA | | 0.2 | 0.5 | mA | 停机模式 | 62 |
| Flash erase/program current IDD | IDD | | 40 | 70 | mA | 擦除/编程周期期间,SYSCLK 为 100MHz,禁用 VREG | 62 |
| Flash erase/program current IDDIO | IDDIO | | 33 | 75 | mA | 擦除/编程周期期间 | 62 |
| Flash erase/program current IDDA | IDDA | | 0.1 | 2.5 | mA | 擦除/编程周期期间 | 62 |
| Low-level output voltage | VOL | | | 0.4 | V | IOL=IOL 最大值 | 68 |
| Low-level output voltage | VOL | | | 0.2 | V | IOL = 100µA | 68 |
| High-level output source current, all output pins | IOH | | -4 | | mA | 所有输出引脚的高电平输出源电流 | 68 |
| Low-level output sink current, all output pins | IOL | | 4 | | mA | 所有输出引脚的低电平输出灌电流 | 68 |
| High-level output impedance, all output pins | ROH | | 70 | | Ω | 所有输出引脚的高电平输出阻抗 | 68 |
| Low-level output impedance, all output pins | ROL | | 70 | | Ω | 所有输出引脚的低电平输出阻抗 | 68 |
| High-level input voltage | VIH | 2 | | | V | (3.3V),max 为公式 VDDIO+0.3 | 68 |
| Low-level input voltage | VIL | | | 0.8 | V | (3.3V),min 为公式 VSS-0.3 | 68 |
| Input hysteresis | VHYSTERESIS | 150 | | | mV | 输入迟滞 | 68 |
| Input current with pulldown | IPULLDOWN | | 100 | | µA | 带下拉的输入;VDDIO = 3.3V,VIN = VDDIO | 68 |
| Input current with pullup, digital input | IPULLUP | | 160 | | µA | 启用上拉的数字输入;VDDIO = 3.3V,VIN = 0V | 68 |
| Input current with pullup, analog input | IPULLUP | | 160 | | µA | 启用上拉的模拟输入;VDDA = 3.3V,VIN = 0V | 68 |
| Pin leakage current, GPIO excluding GPIO23_VSW | ILEAK | | 2 | | µA | 除 GPIO23_VSW 外的所有 GPIO 上拉和输出被禁用;0V ≤ VIN ≤ VDDIO | 68 |
| Pin leakage current, GPIO23_VSW | ILEAK | | 45 | | µA | 0V ≤ VIN ≤ VDDIO | 68 |
| Pin leakage current, analog pins (excluding ADCINB3/VDAC and PGAx_OF) | ILEAK | | 0.1 | | µA | 模拟驱动器禁用;0V ≤ VIN ≤ VDDA | 68 |
| Input capacitance, digital GPIO excluding GPIO23_VSW | CI | | 2 | | pF | 除 GPIO23_VSW 外的所有数字 GPIO | 68 |
| VDDIO power-on reset voltage | VPOR-VDDIO | | 2.3 | | V | VDDIO 上电复位电压 | 68 |
| VDDIO brown-out reset voltage | VBOR-VDDIO | 2.81 | 3 | | V | VDDIO 欠压复位电压 | 68 |
| Internal regulator output | VVREG | | 1.2 | | V | 内部 VREG 打开 | 68 |
| Crystal oscillator load capacitance | CL1, CL2 | 12 | | 24 | pF | 晶体振荡器负载电容 | 94 |
| Crystal shunt capacitance | C0 | | | 7 | pF | 晶振并联电容 | 94 |
| INTOSC1 and INTOSC2 frequency | fINTOSC | 9.7 | 10 | 10.3 | MHz | INTOSC1 和 INTOSC2 | 95 |
| INTOSC frequency stability at room temperature | fINTOSC-STABILITY | -0.1 | | 0.1 | % | 30°C,标称 VDD | 96 |
| INTOSC frequency stability over VDD | fINTOSC-STABILITY | -0.2 | | 0.2 | % | VDD 上的频率稳定性,30°C | 96 |
| INTOSC frequency stability over temperature | fINTOSC-STABILITY | -3 | | 3 | % | 频率稳定性 | 96 |
| ESD human body model (HBM), all pins | V(ESD) | -2000 | | 2000 | V | 64 引脚 PM 封装,Q 温度范围,符合 AEC Q100-002,所有引脚 | 60 |
| ESD charged device model (CDM), all pins | V(ESD) | -500 | | 500 | V | 64 引脚 PM 封装,Q 温度范围,符合 AEC Q100-011,所有引脚 | 60 |
| ESD charged device model (CDM), corner pins | V(ESD) | -750 | | 750 | V | 64 引脚 PM 上的转角引脚 1、16、17、32、33、48、49、64 | 60 |
## CAD (KiCad official)
- Symbol: `F280040CPMQR`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: QFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `f280040cpmqr-etched.step` / `f280040cpmqr-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `f280040cpmqr.step` / `f280040cpmqr.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/f280040cpmqr.pdf) (270 pp, sha256 `f0eccdafc7ec75fa`, retrieved 2026-11-10, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/f280040cpmqr-datasheet.pdf)