component
F280036PMRQ1
Public Made by Adomby adom
Texas Instruments Microcontrollers (MCU/MPU/SOC), LQFP-64(10x10). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
355d809
F280036PMRQ1
Texas Instruments · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
F280036PMRQ1 from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates SCIA_TX, EPWM7_B, EQEP1_B, LINA_RX, I2CB_SCL, HIC_NCS and AUXCLKIN. |
| 2 | GPIO28 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates SCIA_RX, EPWM7_A, EQEP1_A, LINA_TX, I2CB_SDA and ERRORSTS, which requires an external pull-down. |
| 3 | XRSn | bidirectional | Open-drain device reset input and watchdog reset output with internal pull-up; it needs a 2.2 kΩ to 10 kΩ resistor to VDDIO and at most 100 nF to VSS, and is driven low for 512 OSCCLK cycles on a watchdog reset. |
| 4 | VDD | power_in | 1.2 V digital logic supply (recommended 1.14 V to 1.32 V), decoupled per the PMM section. |
| 5 | VSS | power_in | Digital ground, to be connected to the board ground. |
| 6 | A6 | input | ADC-A analog input 6 (also CMPSS-1 input and AIO228); keep the input below VDDA + 0.3 V. |
| 7 | B2,C6 | input | ADC-B input 2 / ADC-C input 6 (also CMPSS-3 input and AIO226); keep the input below VDDA + 0.3 V. |
| 8 | A3,B3,C5,VDAC | input | ADC-A input 3, ADC-B input 3, ADC-C input 5, and optional external reference for the on-chip DAC; at least 1 µF is required on VDAC if used as a DAC reference. |
| 9 | A2,B6,C9 | input | ADC-A input 2 / ADC-B input 6 / ADC-C input 9 (also CMPSS-1 input and AIO224); keep the input below VDDA + 0.3 V. |
| 10 | A15,B9,C7 | input | ADC-A input 15 / ADC-B input 9 / ADC-C input 7 (also CMPSS-1 input); keep the input below VDDA + 0.3 V. |
| 11 | A14,B14,C4 | input | ADC-A input 14 / ADC-B input 14 / ADC-C input 4 (also CMPSS-3 input and AIO239); keep the input below VDDA + 0.3 V. |
| 12 | A11,B10,C0 | input | ADC-A input 11 / ADC-B input 10 / ADC-C input 0 (also CMPSS-1 input and AIO237); keep the input below VDDA + 0.3 V. |
| 13 | A5,B12,C2 | input | ADC-A input 5 / ADC-B input 12 / ADC-C input 2 (also CMPSS-2/3 inputs and AIO244); keep the input below VDDA + 0.3 V. |
| 14 | A1,B7,DACB_OUT | input | ADC-A input 1 / ADC-B input 7 (also CMPSS-1 input); this pin is also the buffered DAC-B output, so the ADC use and DAC use are mutually exclusive in practice. |
| 15 | A0,B15,C15,DACA_OUT | input | ADC-A input 0 / ADC-B input 15 / ADC-C input 15 (also CMPSS-3 input); this pin is also the buffered DAC-A output. |
| 16 | VREFHI | input | ADC high reference: driven externally (2.4 V to VDDA) or generated internally (1.65 V or 2.5 V), with at least 2.2 µF placed between VREFHI and VREFLO. |
| 17 | VREFLO | input | ADC low reference, connected to analog ground VSSA. |
| 18 | A12,C1 | input | ADC-A input 12 / ADC-C input 1 (also CMPSS-2/4 inputs and AIO238/AIO248); keep the input below VDDA + 0.3 V. |
| 19 | A7,C3 | input | ADC-A input 7 / ADC-C input 3 (also CMPSS-4 input and AIO245); keep the input below VDDA + 0.3 V. |
| 20 | A8,B0,C11 | input | ADC-A input 8 / ADC-B input 0 / ADC-C input 11 (also CMPSS-2/4 inputs and AIO241); keep the input below VDDA + 0.3 V. |
| 21 | VSSA | power_in | Analog ground for the ADC, comparator and DAC blocks. |
| 22 | VDDA | power_in | 3.3 V analog supply; place at least 2.2 µF decoupling on this pin. |
| 23 | A4,B8,C14 | input | ADC-A input 4 / ADC-B input 8 / ADC-C input 14 (also CMPSS-2/4 inputs and AIO225); keep the input below VDDA + 0.3 V. |
| 24 | A9,B4,C8 | input | ADC-A input 9 / ADC-B input 4 / ADC-C input 8 (also CMPSS-2/4 inputs and AIO227/AIO236); keep the input below VDDA + 0.3 V. |
| 25 | A10,B1,C10 | input | ADC-A input 10 / ADC-B input 1 / ADC-C input 10 (also CMPSS-2 inputs and AIO230); keep the input below VDDA + 0.3 V. |
| 26 | VSS | power_in | Digital ground, to be connected to the board ground. |
| 27 | VDD | power_in | 1.2 V digital logic supply (recommended 1.14 V to 1.32 V). |
| 28 | VDDIO | power_in | 3.3 V digital I/O supply (2.8 V to 3.63 V, 3.3 V nominal). |
| 29 | GPIO13 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM7_B, MCAN_TX, SCIB_RX, PMBUSA_ALERT, SPIA_SOMI and HIC_D5. |
| 30 | GPIO12 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM7_A, MCAN_RX, SCIB_TX, PMBUSA_CTL, SPIA_CLK and HIC_INT. |
| 31 | GPIO11 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM6_B, EQEP1_B, SCIB_RX, SPIA_STE, LINB_RX and HIC_NBE0. |
| 32 | GPIO33 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates I2CA_SCL, SPIB_STE, LINA_RX, SD1_C2, ADCSOCAO and HIC_D0. |
| 33 | GPIO16 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates SPIA_SIMO, EPWM5_A, SCIA_TX, SD1_D1, XCLKOUT and SPIB_SOMI. |
| 34 | GPIO17 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates SPIA_SOMI, EPWM5_B, SCIA_RX, SD1_C1, CANA_TX and PMBUSA_SDA. |
| 35 | GPIO24 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SCIA_TX and ERRORSTS, which requires an external pull-down. |
| 36 | TCK | input | JTAG test clock with internal pull-up enabled. |
| 37 | GPIO37/TDO | output | JTAG test data output (default function) that is tri-stated when no JTAG activity occurs, so an internal pull-up or external pull-up should be fitted; the pin can be used as GPIO37 in cJTAG mode. |
| 38 | TMS | bidirectional | JTAG test mode select with internal pull-up; a 2.2 kΩ external pull-up to VDDIO is recommended and the device has no TRSTn pin. |
| 39 | GPIO35/TDI | input | JTAG test data input (default function) with internal pull-up disabled by default, so an internal or external pull-up is required when used as TDI; it can be used as GPIO35 in cJTAG mode. |
| 40 | GPIO32 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D2, CANA_TX and HIC_INT. |
| 41 | GPIO18/X2 | bidirectional | General-purpose I/O (GPIO18) or crystal oscillator output X2 when the XTAL is enabled; the XTAL and GPIO functions are mutually exclusive. |
| 42 | GPIO19/X1 | bidirectional | General-purpose I/O (GPIO19) or crystal/single-ended clock input X1; the XTAL must be configured by initialization software before enabling the oscillator. |
| 43 | VDDIO | power_in | 3.3 V digital I/O supply (2.8 V to 3.63 V). |
| 44 | VDD | power_in | 1.2 V digital logic supply (recommended 1.14 V to 1.32 V). |
| 45 | VSS | power_in | Digital ground, to be connected to the board ground. |
| 46 | VREGENZ | input | Internal regulator enable with internal pull-down: tie low to VSS to enable the internal 1.2 V VREG, or tie high to VDDIO to supply VDD externally. |
| 47 | GPIO8 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM5_A, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL and HIC_A0. |
| 48 | GPIO4 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM3_A, MCAN_TX, OUTPUTXBAR3, CANA_TX, SPIB_CLK and EQEP2_STROBE. |
| 49 | GPIO3 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and I2CB_SCL. |
| 50 | GPIO2 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SPIA_SIMO, SCIA_TX and I2CB_SDA. |
| 51 | GPIO1 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM1_B, I2CA_SCL, SPIA_SOMI, MCAN_TX and CLB_OUTPUTXBAR7. |
| 52 | GPIO0 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM1_A, I2CA_SDA, SPIA_STE, MCAN_RX and EQEP1_INDEX. |
| 53 | GPIO40 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates SPIB_SIMO, EPWM2_B, PMBUSA_SDA, SCIB_TX, EQEP1_A and LINB_TX. |
| 54 | GPIO23 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EQEP1_INDEX, SCIB_RX, SPIB_STE, SD1_C4, LINA_RX and EPWM4_B. |
| 55 | GPIO41 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM2_A, PMBUSA_SCL, FSIRXA_D1, SCIB_RX, EQEP1_B and SPIB_SOMI. |
| 56 | GPIO22 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EQEP1_STROBE, SCIB_TX, SPIB_CLK, SD1_D4, LINA_TX and EPWM4_A. |
| 57 | GPIO7 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM4_B, OUTPUTXBAR5, EQEP1_B, SPIB_SIMO, FSITXA_CLK and HIC_A6. |
| 58 | VSS | power_in | Digital ground, to be connected to the board ground. |
| 59 | VDD | power_in | 1.2 V digital logic supply (recommended 1.14 V to 1.32 V). |
| 60 | VDDIO | power_in | 3.3 V digital I/O supply (2.8 V to 3.63 V). |
| 61 | GPIO5 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM3_B, OUTPUTXBAR3, MCAN_RX, CANA_RX, SPIA_STE and FSITXA_D1. |
| 62 | GPIO9 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX and I2CB_SCL. |
| 63 | GPIO10 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM6_A, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI and I2CA_SDA. |
| 64 | GPIO6 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, SPIB_SOMI and FSITXA_D0. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Low-level output voltage | VOL | 0.4 | V | IOL = IOL max | 71 | ||
| Low-level output voltage | VOL | 0.2 | V | IOL = 100 µA | 71 | ||
| High-level output source current, all output pins | IOH | -4 | mA | 71 | |||
| Low-level output sink current, all output pins | IOL | 4 | mA | 71 | |||
| High-level output impedance, all output pins | ROH | 50 | 66 | 96 | Ω | VOH = VDDIO-0.4V | 71 |
| Low-level output impedance, all output pins | ROL | 48 | 60 | 84 | Ω | VOL = 0.4V | 71 |
| High-level input voltage | VIH | 2 | V | 71 | |||
| Low-level input voltage | VIL | 0.8 | V | 71 | |||
| Weak pulldown resistance | RPULLDOWN | 22 | 31 | 62 | kΩ | 71 | |
| Weak pullup resistance | RPULLUP | 19 | 30 | 54 | kΩ | 71 | |
| Internal regulator output | VVREG | 1.14 | 1.2 | 1.32 | V | 83 | |
| VDDIO supply ramp-up rate | SRVDDIO-UP | 8 | 100 | mV/μs | 83 | ||
| VDDIO supply ramp-down rate | SRVDDIO-DN | 20 | 100 | mV/μs | 83 | ||
| VDD (1.2V rail) supply ramp-up rate | SRVDD-UP | 3.5 | 100 | mV/μs | External VREG | 83 | |
| VDD (1.2V rail) supply ramp-down rate | SRVDD-DN | 10 | 100 | mV/μs | External VREG | 83 | |
| INTOSC1/INTOSC2 frequency | fINTOSC | 9.82 | 10 | 10.1 | MHz | -40℃ to 125℃ | 100 |
| INTOSC1/INTOSC2 frequency | fINTOSC | 9.86 | 10 | 10.1 | MHz | -30℃ to 90℃ | 100 |
| INTOSC1/INTOSC2 frequency | fINTOSC | 9.9 | 10 | 10.1 | MHz | -10℃ to 85℃ | 100 |
| Crystal load capacitance | CL1, CL2 | 12 | 24 | pF | 98 | ||
| Crystal shunt capacitance | C0 | 7 | pF | 98 | |||
| PMBus low-level input voltage | VIL | 0.8 | V | 171 | |||
| PMBus high-level input voltage | VIH | 2.1 | V | 171 | |||
| PMBus low-level output voltage | VOL | 0.4 | V | Ipullup = 4mA | 171 | ||
| Suppressed spike pulse width (input filter) | tSP | 0 | 50 | ns | 171 | ||
| Input leakage current per pin (PMBus) | Ii | -10 | 10 | µA | 0.1Vbus < Vi < 0.9Vbus | 171 | |
| SCL clock frequency, fast mode | fSCL | 10 | 400 | kHz | 171 | ||
| SCL clock frequency, standard mode | fSCL | 10 | 100 | kHz | 172 | ||
| SDA and SCL rise time, fast mode | tr | 20 | 300 | ns | 5% to 95% | 171 | |
| SDA and SCL fall time, fast mode | tf | 20 | 300 | ns | 95% to 5% | 171 | |
| CMPSS comparator input-referred offset | -20 | 20 | mV | Low common mode, inverting input set at 50mV | 141 | ||
| CMPSS DAC static offset error | -25 | 25 | mV | 142 | |||
| CMPSS DAC static gain error | -2 | 2 | FSR 百分比 | 142 | |||
| CMPSS DAC static INL | -16 | 16 | LSB | corrected endpoints | 142 | ||
| CMPSS DAC static DNL | -1 | 4 | LSB | corrected endpoints | 142 | ||
| CMPSS DAC output interference error | -100 | 100 | LSB | 142 | |||
| VDAC reference load | VDAC | 6 | 8 | 10 | kΩ | When VDAC is used as reference | 142 |
| Buffered DAC midpoint offset error | -10 | 10 | mV | Midpoint | 146 | ||
| Buffered DAC gain error | -2.5 | 2.5 | FSR 百分比 | 146 | |||
| Buffered DAC DNL | -1 | 1 | LSB | corrected endpoints | 146 | ||
| Buffered DAC INL | -5 | 5 | LSB | corrected endpoints | 146 | ||
| Buffered DAC load regulation | -1 | 1 | mV/V | 146 | |||
| Buffered DAC reference input resistance | VDAC or VREFHI | 160 | 200 | 240 | kΩ | VDAC or VREFHI | 146 |
| Buffered DAC valid output voltage range | VOUT | 0.3 | V | RL = 5kΩ | 146 | ||
| Buffered DAC valid output voltage range | VOUT | 0.6 | V | RL = 1kΩ | 146 |
CAD (KiCad official)
- Symbol:
F280036PMRQ1 - Footprint:
Package_QFP:LQFP-64_10x10mm_P0.5mm - 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files:
f280036pmrq1-etched.step/f280036pmrq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);f280036pmrq1.step/f280036pmrq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (285 pp, sha256
4385cb7a74ef5d7f, retrieved 2026-11-13, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# F280036PMRQ1
**Texas Instruments** · Microcontrollers (MCU/MPU/SOC) · LQFP-64(10x10)
F280036PMRQ1 from Texas Instruments, in a LQFP-64(10x10). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GPIO29 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates SCIA_TX, EPWM7_B, EQEP1_B, LINA_RX, I2CB_SCL, HIC_NCS and AUXCLKIN. |
| 2 | GPIO28 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates SCIA_RX, EPWM7_A, EQEP1_A, LINA_TX, I2CB_SDA and ERRORSTS, which requires an external pull-down. |
| 3 | XRSn | bidirectional | Open-drain device reset input and watchdog reset output with internal pull-up; it needs a 2.2 kΩ to 10 kΩ resistor to VDDIO and at most 100 nF to VSS, and is driven low for 512 OSCCLK cycles on a watchdog reset. |
| 4 | VDD | power_in | 1.2 V digital logic supply (recommended 1.14 V to 1.32 V), decoupled per the PMM section. |
| 5 | VSS | power_in | Digital ground, to be connected to the board ground. |
| 6 | A6 | input | ADC-A analog input 6 (also CMPSS-1 input and AIO228); keep the input below VDDA + 0.3 V. |
| 7 | B2,C6 | input | ADC-B input 2 / ADC-C input 6 (also CMPSS-3 input and AIO226); keep the input below VDDA + 0.3 V. |
| 8 | A3,B3,C5,VDAC | input | ADC-A input 3, ADC-B input 3, ADC-C input 5, and optional external reference for the on-chip DAC; at least 1 µF is required on VDAC if used as a DAC reference. |
| 9 | A2,B6,C9 | input | ADC-A input 2 / ADC-B input 6 / ADC-C input 9 (also CMPSS-1 input and AIO224); keep the input below VDDA + 0.3 V. |
| 10 | A15,B9,C7 | input | ADC-A input 15 / ADC-B input 9 / ADC-C input 7 (also CMPSS-1 input); keep the input below VDDA + 0.3 V. |
| 11 | A14,B14,C4 | input | ADC-A input 14 / ADC-B input 14 / ADC-C input 4 (also CMPSS-3 input and AIO239); keep the input below VDDA + 0.3 V. |
| 12 | A11,B10,C0 | input | ADC-A input 11 / ADC-B input 10 / ADC-C input 0 (also CMPSS-1 input and AIO237); keep the input below VDDA + 0.3 V. |
| 13 | A5,B12,C2 | input | ADC-A input 5 / ADC-B input 12 / ADC-C input 2 (also CMPSS-2/3 inputs and AIO244); keep the input below VDDA + 0.3 V. |
| 14 | A1,B7,DACB_OUT | input | ADC-A input 1 / ADC-B input 7 (also CMPSS-1 input); this pin is also the buffered DAC-B output, so the ADC use and DAC use are mutually exclusive in practice. |
| 15 | A0,B15,C15,DACA_OUT | input | ADC-A input 0 / ADC-B input 15 / ADC-C input 15 (also CMPSS-3 input); this pin is also the buffered DAC-A output. |
| 16 | VREFHI | input | ADC high reference: driven externally (2.4 V to VDDA) or generated internally (1.65 V or 2.5 V), with at least 2.2 µF placed between VREFHI and VREFLO. |
| 17 | VREFLO | input | ADC low reference, connected to analog ground VSSA. |
| 18 | A12,C1 | input | ADC-A input 12 / ADC-C input 1 (also CMPSS-2/4 inputs and AIO238/AIO248); keep the input below VDDA + 0.3 V. |
| 19 | A7,C3 | input | ADC-A input 7 / ADC-C input 3 (also CMPSS-4 input and AIO245); keep the input below VDDA + 0.3 V. |
| 20 | A8,B0,C11 | input | ADC-A input 8 / ADC-B input 0 / ADC-C input 11 (also CMPSS-2/4 inputs and AIO241); keep the input below VDDA + 0.3 V. |
| 21 | VSSA | power_in | Analog ground for the ADC, comparator and DAC blocks. |
| 22 | VDDA | power_in | 3.3 V analog supply; place at least 2.2 µF decoupling on this pin. |
| 23 | A4,B8,C14 | input | ADC-A input 4 / ADC-B input 8 / ADC-C input 14 (also CMPSS-2/4 inputs and AIO225); keep the input below VDDA + 0.3 V. |
| 24 | A9,B4,C8 | input | ADC-A input 9 / ADC-B input 4 / ADC-C input 8 (also CMPSS-2/4 inputs and AIO227/AIO236); keep the input below VDDA + 0.3 V. |
| 25 | A10,B1,C10 | input | ADC-A input 10 / ADC-B input 1 / ADC-C input 10 (also CMPSS-2 inputs and AIO230); keep the input below VDDA + 0.3 V. |
| 26 | VSS | power_in | Digital ground, to be connected to the board ground. |
| 27 | VDD | power_in | 1.2 V digital logic supply (recommended 1.14 V to 1.32 V). |
| 28 | VDDIO | power_in | 3.3 V digital I/O supply (2.8 V to 3.63 V, 3.3 V nominal). |
| 29 | GPIO13 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM7_B, MCAN_TX, SCIB_RX, PMBUSA_ALERT, SPIA_SOMI and HIC_D5. |
| 30 | GPIO12 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM7_A, MCAN_RX, SCIB_TX, PMBUSA_CTL, SPIA_CLK and HIC_INT. |
| 31 | GPIO11 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM6_B, EQEP1_B, SCIB_RX, SPIA_STE, LINB_RX and HIC_NBE0. |
| 32 | GPIO33 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates I2CA_SCL, SPIB_STE, LINA_RX, SD1_C2, ADCSOCAO and HIC_D0. |
| 33 | GPIO16 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates SPIA_SIMO, EPWM5_A, SCIA_TX, SD1_D1, XCLKOUT and SPIB_SOMI. |
| 34 | GPIO17 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates SPIA_SOMI, EPWM5_B, SCIA_RX, SD1_C1, CANA_TX and PMBUSA_SDA. |
| 35 | GPIO24 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates OUTPUTXBAR1, EQEP2_A, EPWM8_A, SPIB_SIMO, SCIA_TX and ERRORSTS, which requires an external pull-down. |
| 36 | TCK | input | JTAG test clock with internal pull-up enabled. |
| 37 | GPIO37/TDO | output | JTAG test data output (default function) that is tri-stated when no JTAG activity occurs, so an internal pull-up or external pull-up should be fitted; the pin can be used as GPIO37 in cJTAG mode. |
| 38 | TMS | bidirectional | JTAG test mode select with internal pull-up; a 2.2 kΩ external pull-up to VDDIO is recommended and the device has no TRSTn pin. |
| 39 | GPIO35/TDI | input | JTAG test data input (default function) with internal pull-up disabled by default, so an internal or external pull-up is required when used as TDI; it can be used as GPIO35 in cJTAG mode. |
| 40 | GPIO32 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates I2CA_SDA, SPIB_CLK, EPWM8_B, LINA_TX, SD1_D2, CANA_TX and HIC_INT. |
| 41 | GPIO18/X2 | bidirectional | General-purpose I/O (GPIO18) or crystal oscillator output X2 when the XTAL is enabled; the XTAL and GPIO functions are mutually exclusive. |
| 42 | GPIO19/X1 | bidirectional | General-purpose I/O (GPIO19) or crystal/single-ended clock input X1; the XTAL must be configured by initialization software before enabling the oscillator. |
| 43 | VDDIO | power_in | 3.3 V digital I/O supply (2.8 V to 3.63 V). |
| 44 | VDD | power_in | 1.2 V digital logic supply (recommended 1.14 V to 1.32 V). |
| 45 | VSS | power_in | Digital ground, to be connected to the board ground. |
| 46 | VREGENZ | input | Internal regulator enable with internal pull-down: tie low to VSS to enable the internal 1.2 V VREG, or tie high to VDDIO to supply VDD externally. |
| 47 | GPIO8 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM5_A, ADCSOCAO, EQEP1_STROBE, SCIA_TX, SPIA_SIMO, I2CA_SCL and HIC_A0. |
| 48 | GPIO4 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM3_A, MCAN_TX, OUTPUTXBAR3, CANA_TX, SPIB_CLK and EQEP2_STROBE. |
| 49 | GPIO3 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM2_B, OUTPUTXBAR2, PMBUSA_SCL, SPIA_CLK, SCIA_RX and I2CB_SCL. |
| 50 | GPIO2 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM2_A, OUTPUTXBAR1, PMBUSA_SDA, SPIA_SIMO, SCIA_TX and I2CB_SDA. |
| 51 | GPIO1 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM1_B, I2CA_SCL, SPIA_SOMI, MCAN_TX and CLB_OUTPUTXBAR7. |
| 52 | GPIO0 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM1_A, I2CA_SDA, SPIA_STE, MCAN_RX and EQEP1_INDEX. |
| 53 | GPIO40 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates SPIB_SIMO, EPWM2_B, PMBUSA_SDA, SCIB_TX, EQEP1_A and LINB_TX. |
| 54 | GPIO23 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EQEP1_INDEX, SCIB_RX, SPIB_STE, SD1_C4, LINA_RX and EPWM4_B. |
| 55 | GPIO41 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM2_A, PMBUSA_SCL, FSIRXA_D1, SCIB_RX, EQEP1_B and SPIB_SOMI. |
| 56 | GPIO22 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EQEP1_STROBE, SCIB_TX, SPIB_CLK, SD1_D4, LINA_TX and EPWM4_A. |
| 57 | GPIO7 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM4_B, OUTPUTXBAR5, EQEP1_B, SPIB_SIMO, FSITXA_CLK and HIC_A6. |
| 58 | VSS | power_in | Digital ground, to be connected to the board ground. |
| 59 | VDD | power_in | 1.2 V digital logic supply (recommended 1.14 V to 1.32 V). |
| 60 | VDDIO | power_in | 3.3 V digital I/O supply (2.8 V to 3.63 V). |
| 61 | GPIO5 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM3_B, OUTPUTXBAR3, MCAN_RX, CANA_RX, SPIA_STE and FSITXA_D1. |
| 62 | GPIO9 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM5_B, SCIB_TX, OUTPUTXBAR6, EQEP1_INDEX, SCIA_RX and I2CB_SCL. |
| 63 | GPIO10 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM6_A, ADCSOCBO, EQEP1_A, SCIB_TX, SPIA_SOMI and I2CA_SDA. |
| 64 | GPIO6 | bidirectional | General-purpose I/O referenced to VDDIO (3.3 V) with alternates EPWM4_A, OUTPUTXBAR4, SYNCOUT, EQEP1_A, SPIB_SOMI and FSITXA_D0. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | LQFP-64(10x10) |
| Category | Embedded Processors & Controllers |
| Pins | 64 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Low-level output voltage | VOL | | | 0.4 | V | IOL = IOL max | 71 |
| Low-level output voltage | VOL | | | 0.2 | V | IOL = 100 µA | 71 |
| High-level output source current, all output pins | IOH | -4 | | | mA | | 71 |
| Low-level output sink current, all output pins | IOL | 4 | | | mA | | 71 |
| High-level output impedance, all output pins | ROH | 50 | 66 | 96 | Ω | VOH = VDDIO-0.4V | 71 |
| Low-level output impedance, all output pins | ROL | 48 | 60 | 84 | Ω | VOL = 0.4V | 71 |
| High-level input voltage | VIH | 2 | | | V | | 71 |
| Low-level input voltage | VIL | | | 0.8 | V | | 71 |
| Weak pulldown resistance | RPULLDOWN | 22 | 31 | 62 | kΩ | | 71 |
| Weak pullup resistance | RPULLUP | 19 | 30 | 54 | kΩ | | 71 |
| Internal regulator output | VVREG | 1.14 | 1.2 | 1.32 | V | | 83 |
| VDDIO supply ramp-up rate | SRVDDIO-UP | 8 | | 100 | mV/μs | | 83 |
| VDDIO supply ramp-down rate | SRVDDIO-DN | 20 | | 100 | mV/μs | | 83 |
| VDD (1.2V rail) supply ramp-up rate | SRVDD-UP | 3.5 | | 100 | mV/μs | External VREG | 83 |
| VDD (1.2V rail) supply ramp-down rate | SRVDD-DN | 10 | | 100 | mV/μs | External VREG | 83 |
| INTOSC1/INTOSC2 frequency | fINTOSC | 9.82 | 10 | 10.1 | MHz | -40℃ to 125℃ | 100 |
| INTOSC1/INTOSC2 frequency | fINTOSC | 9.86 | 10 | 10.1 | MHz | -30℃ to 90℃ | 100 |
| INTOSC1/INTOSC2 frequency | fINTOSC | 9.9 | 10 | 10.1 | MHz | -10℃ to 85℃ | 100 |
| Crystal load capacitance | CL1, CL2 | 12 | | 24 | pF | | 98 |
| Crystal shunt capacitance | C0 | | | 7 | pF | | 98 |
| PMBus low-level input voltage | VIL | | | 0.8 | V | | 171 |
| PMBus high-level input voltage | VIH | 2.1 | | | V | | 171 |
| PMBus low-level output voltage | VOL | | | 0.4 | V | Ipullup = 4mA | 171 |
| Suppressed spike pulse width (input filter) | tSP | 0 | | 50 | ns | | 171 |
| Input leakage current per pin (PMBus) | Ii | -10 | | 10 | µA | 0.1Vbus < Vi < 0.9Vbus | 171 |
| SCL clock frequency, fast mode | fSCL | 10 | | 400 | kHz | | 171 |
| SCL clock frequency, standard mode | fSCL | 10 | | 100 | kHz | | 172 |
| SDA and SCL rise time, fast mode | tr | 20 | | 300 | ns | 5% to 95% | 171 |
| SDA and SCL fall time, fast mode | tf | 20 | | 300 | ns | 95% to 5% | 171 |
| CMPSS comparator input-referred offset | | -20 | | 20 | mV | Low common mode, inverting input set at 50mV | 141 |
| CMPSS DAC static offset error | | -25 | | 25 | mV | | 142 |
| CMPSS DAC static gain error | | -2 | | 2 | FSR 百分比 | | 142 |
| CMPSS DAC static INL | | -16 | | 16 | LSB | corrected endpoints | 142 |
| CMPSS DAC static DNL | | -1 | | 4 | LSB | corrected endpoints | 142 |
| CMPSS DAC output interference error | | -100 | | 100 | LSB | | 142 |
| VDAC reference load | VDAC | 6 | 8 | 10 | kΩ | When VDAC is used as reference | 142 |
| Buffered DAC midpoint offset error | | -10 | | 10 | mV | Midpoint | 146 |
| Buffered DAC gain error | | -2.5 | | 2.5 | FSR 百分比 | | 146 |
| Buffered DAC DNL | | -1 | | 1 | LSB | corrected endpoints | 146 |
| Buffered DAC INL | | -5 | | 5 | LSB | corrected endpoints | 146 |
| Buffered DAC load regulation | | -1 | | 1 | mV/V | | 146 |
| Buffered DAC reference input resistance | VDAC or VREFHI | 160 | 200 | 240 | kΩ | VDAC or VREFHI | 146 |
| Buffered DAC valid output voltage range | VOUT | 0.3 | | | V | RL = 5kΩ | 146 |
| Buffered DAC valid output voltage range | VOUT | 0.6 | | | V | RL = 1kΩ | 146 |
## CAD (KiCad official)
- Symbol: `F280036PMRQ1`
- Footprint: `Package_QFP:LQFP-64_10x10mm_P0.5mm`
- 3D model: LQFP-64(10x10) (KiCad packages3D, STEP)
- 3D model files: `f280036pmrq1-etched.step` / `f280036pmrq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `f280036pmrq1.step` / `f280036pmrq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com.cn/cn/lit/ds/symlink/tms320f280036-q1.pdf?ts=1738808441451&ref_url=https%253A%252F%252Fwww.ti.com.cn%252Fsitesearch%252Fzh-cn%252Fdocs%252Funiversalsearch.tsp%253FlangPref%253Dzh-CN%2526nr%253D23%2526searchTerm%253DF280036PMRQ1) (285 pp, sha256 `4385cb7a74ef5d7f`, retrieved 2026-11-13, tier: manufacturer)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/f280036pmrq1-datasheet.pdf)