main
History Download
Ray Publish 0.1.0 574ce41

F1478NLGA8

RENESAS · RF Amplifiers · QFN-16(3x3)

F1478NLGA8 from RENESAS, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Internally grounded; this pin must be grounded with a via as close to the pin as possible.
2 RFIN input RF input internally matched to 50Ω; an external DC block must be used.
3 GND power_in Internally grounded; this pin must be grounded with a via as close to the pin as possible.
4 VCC-RF power_in Pulled up to Vcc through an inductor with bypass capacitors placed as close to the pin as possible; it also carries an RF signal.
5 NC unconnected No internal connection; may be left unconnected or connected to ground (recommended) using a via placed as close to the pin as possible.
6 NC unconnected No internal connection; may be left unconnected or connected to ground (recommended) using a via placed as close to the pin as possible.
7 NC unconnected No internal connection; may be left unconnected or connected to ground (recommended) using a via placed as close to the pin as possible.
8 NC unconnected No internal connection; may be left unconnected or connected to ground (recommended) using a via placed as close to the pin as possible.
9 GND power_in Internally grounded per Table 1; this pin must be grounded with a via as close to the pin as possible.
10 RFOUT output RF output that is pulled up to Vcc through an inductor and requires an external DC block.
11 RFOUT output RF output that is pulled up to Vcc through an inductor and requires an external DC block.
12 GND power_in Internally grounded; this pin must be grounded with a via as close to the pin as possible.
13 BIAS_1 passive Connected via a resistor to a common Vcc with bypass capacitors placed as close to the pin as possible, as shown in the Typical Application Circuit.
14 BIAS_2 passive Connected via an inductor to ground.
15 RSET passive Connected via a resistor to ground; the resistor value sets the device into its low or high power mode.
16 STBY input Standby pin, 1.8V logic compatible: logic LOW powers the amplifier off, while logic HIGH or an unconnected pin gives full operation.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer RENESAS
Package QFN-16(3x3)
Category RF & Radio
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VCC to GND VCC -0.3 6 V 9
STBY voltage VCTL -0.3 V max printed as lower of (5.0, VCC + 0.25) 9
BIAS_1 current into pin IBIAS_1 20 mA BIAS_1 (into pin) 9
BIAS_2 current out of pin IBIAS_2 10 mA BIAS_2 (out of pin) 9
RFIN externally applied DC voltage VRFIN -0.5 0.5 V 9
RFOUT externally applied DC voltage VRFOUT -0.5 5.5 V 9
Maximum CW input power, Standby ON PMAX_IN_ON 21 dBm 24 hours, VCC = 5V, TEPAD = 115°C, VSWR < 2:1, Standby = logic HIGH ON state 9
Maximum CW input power, Standby OFF PMAX_IN_OFF 21 dBm 24 hour, VCC = 5V, TEPAD = 115°C, VSWR < 2:1, Standby = logic LOW OFF state 9
Continuous power dissipation PDISS 1.8 W 9
Storage temperature range Tst -65 150 °C 9
Lead temperature (soldering) 260 °C soldering, 10 s 9
ESD HBM VESDHBM 500 V JEDEC/ESDA JS-001-2012 (Class 1B) 9
ESD CDM VESDCDM 1000 V JEDEC 22-C101F (Class C3) 9
Power supply voltage VCC 3.15 5.25 V 10
Operating temperature range (exposed paddle) TEPAD -40 115 °C Exposed paddle 10
Junction temperature, amplifier Tj 150 °C 10
RF frequency range, Band 2p0 tuning set fRF 1.8 2.2 GHz Band 2p0 Tuning Set 10
RF frequency range, Band 2p5 tuning set fRF 2.3 2.7 GHz Band 2p5 Tuning Set 10
RF frequency range, Band 3p5 tuning set fRF 3.3 3.8 GHz Band 3p5 Tuning Set 10
RF frequency range, Band 4p7 tuning set fRF 4.4 5 GHz Band 4p7 Tuning Set 10
Logic input high VIH 1.17 V maximum printed as VCC 11
Logic input low VIL -0.3 0.63 V 11
Logic current ISTBY -10 10 µA STBY 11
Quiescent current, low power mode ICC_QL 100 130 mA Low Power Mode: R3 = 16kΩ 11
Quiescent current, high power mode ICC_QH 140 178 mA High Power Mode: R3 = 10kΩ 11
Standby current ICC_STBY 1.5 mA STBY = LOW 11
Standby switching time, on tON 270 ns 50% STBY control to within 0.5dB of the on-state final gain value 11
Standby switching time, off tOFF 60 ns 50% STBY control to 30dBc below nominal gain value 11
Noise figure, Band 2p0 low power NF 1.7 dB 12
Output third order intercept point, Band 2p0 low power OIP3 32 dBm POUT = +2dBm / tone, 1MHz tone separation 12
Output 1dB compression point, Band 2p0 low power OP1dB 23.3 dBm 12
Noise figure, Band 2p0 high power NF 1.8 dB 13
Output 1dB compression point, Band 2p0 high power OP1dB 24 dBm 13
Noise figure, Band 2p5 low power NF 1.7 dB 14
Output third order intercept point, Band 2p5 low power OIP3 32.2 dBm POUT = +2dBm / tone, 1MHz tone separation 14
Output 1dB compression point, Band 2p5 low power OP1dB 22.8 dBm 14
Noise figure, Band 2p5 high power NF 1.6 dB 15
Output third order intercept point, Band 2p5 high power OIP3 35.7 dBm POUT = +2dBm / tone, 1MHz tone separation 15
Output 1dB compression point, Band 2p5 high power OP1dB 23.6 dBm 15
Noise figure, Band 3p5 low power NF 1.7 2.5 dB 16
Output third order intercept point, Band 3p5 low power OIP3 31.2 32.3 dBm POUT = +2dBm / tone, 1MHz tone separation 16
Output third order intercept point, Band 3p5 low power, VCC range OIP3 29.3 dBm POUT = +2dBm / tone, VCC = 4.75V to 5.25V, TEPAD = -40°C to +115°C 16
Output 1dB compression point, Band 3p5 low power OP1dB 21.2 22.4 dBm 16
Output 1dB compression point, Band 3p5 low power, VCC range OP1dB 19.3 dBm VCC = 4.75V to 5.25V, TEPAD = -40°C to +115°C 16
Noise figure, Band 3p5 high power NF 1.8 2.5 dB 17
Output third order intercept point, Band 3p5 high power OIP3 35.3 37 dBm POUT = +2dBm / tone, 1MHz tone separation 17
Output third order intercept point, Band 3p5 high power, VCC range OIP3 33.3 dBm POUT = +2dBm / tone, VCC = 4.75V to 5.25V, TEPAD = -40°C to +115°C 17
Output 1dB compression point, Band 3p5 high power OP1dB 22.5 24 dBm 17
Output 1dB compression point, Band 3p5 high power, VCC range OP1dB 21.5 dBm VCC = 4.75V to 5.25V, TEPAD = -40°C to +115°C 17
Noise figure, Band 4p7 low power NF 1.9 dB 18
Output third order intercept point, Band 4p7 low power OIP3 37 dBm POUT = +2dBm / tone, 1MHz tone separation 18
Output 1dB compression point, Band 4p7 low power OP1dB 24.5 dBm 18
Noise figure, Band 4p7 high power NF 1.9 dB 19
Output third order intercept point, Band 4p7 high power OIP3 42.1 dBm POUT = +2dBm / tone, 1MHz tone separation 19
Output 1dB compression point, Band 4p7 high power OP1dB 25.1 dBm 19
Junction to ambient thermal resistance θJA 67.9 °C/W Junction to ambient 20
Junction to case thermal resistance θJC_BOT 22.9 °C/W Case defined as the exposed paddle 20

CAD (KiCad official)

  • Symbol: F1478NLGA8
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
  • 3D model files: f1478nlga8-etched.step / f1478nlga8-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); f1478nlga8.step / f1478nlga8.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: RENESAS datasheet (49 pp, sha256 34f1b35d4eb8c0a6, retrieved 2026-11-02, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF