component
ETA9638E8A
Public Made by Adomby adom
ETA(钰泰) Battery Management, ESOP-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
2bc6a41
ETA9638E8A
ETA(钰泰) · Battery Management · ESOP-8
ETA9638E8A from ETA(钰泰), in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ACIN | power_in | Charger input pin that connects to an AC adaptor or USB charger output; the absolute maximum ACIN voltage is 6.0V and the miniUSB input voltage range is 4.5V to 6.0V. |
| 2 | BAT | power_in | Battery input pin that must be bypassed to GND with a 10uF or greater ceramic capacitor. |
| 3 | EN | input | Enable pin for the IC: drive high to enable, low or floating to disable. |
| 4 | SW | passive | Switching node of the switching regulator; connect a 1uH to 4.7uH inductor between SW and the positive terminal of the battery. |
| 5 | OUT | power_out | Boost output pin that must be bypassed closely to ground with a 22uF or larger ceramic capacitor; the absolute maximum OUT voltage is 5.0V. |
| 6 | GP | power_in | Power ground pin. |
| 7 | STAT | output | Open-drain charge status output that goes low while the battery is charging and becomes high-impedance when the charge cycle completes. |
| 8 | ISET | passive | Charge current set pin: connect a resistor Rset from ISET to GND, setting the fast charge current as Icharge = 1000/Rset (A). |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ETA(钰泰) |
| Package | ESOP-8 |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output USB Voltage Range | 4.8 | 5 | 5.2 | V | 2 | ||
| Charge Termination Voltage | 4.15 | 4.2 | 4.24 | V | 2 | ||
| Charging Current | 0.85 | 1 | 1.15 | A | Charging current =1000/R1, when R1=1K | 2 | |
| Switching Frequency | 1.2 | 1.8 | 2.4 | MHz | 2 | ||
| Quiescent Current from battery | 100 | μA | VBAT=3.6V, No load | 2 | |||
| Maximum Duty Cycle | 90 | % | 2 | ||||
| ACIN Voltage | -0.3 | 6 | V | 2 | |||
| OUT Voltage | -0.3 | 5 | V | 2 | |||
| Operating Temperature Range | -40 | 85 | °C | 2 | |||
| Storage Temperature Range | -55 | 150 | °C | 2 | |||
| Thermal Resistance junction-to-case | θJC | 10 | °C/W | ESOP-8 | 2 |
CAD (KiCad official)
- Symbol:
ETA9638E8A - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
eta9638e8a-etched.step/eta9638e8a-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);eta9638e8a.step/eta9638e8a.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: ETA(钰泰) datasheet (5 pp, sha256
26e3ae895e6b9d2d, retrieved 2026-11-07, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ETA9638E8A
**ETA(钰泰)** · Battery Management · ESOP-8
ETA9638E8A from ETA(钰泰), in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ACIN | power_in | Charger input pin that connects to an AC adaptor or USB charger output; the absolute maximum ACIN voltage is 6.0V and the miniUSB input voltage range is 4.5V to 6.0V. |
| 2 | BAT | power_in | Battery input pin that must be bypassed to GND with a 10uF or greater ceramic capacitor. |
| 3 | EN | input | Enable pin for the IC: drive high to enable, low or floating to disable. |
| 4 | SW | passive | Switching node of the switching regulator; connect a 1uH to 4.7uH inductor between SW and the positive terminal of the battery. |
| 5 | OUT | power_out | Boost output pin that must be bypassed closely to ground with a 22uF or larger ceramic capacitor; the absolute maximum OUT voltage is 5.0V. |
| 6 | GP | power_in | Power ground pin. |
| 7 | STAT | output | Open-drain charge status output that goes low while the battery is charging and becomes high-impedance when the charge cycle completes. |
| 8 | ISET | passive | Charge current set pin: connect a resistor Rset from ISET to GND, setting the fast charge current as Icharge = 1000/Rset (A). |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | ETA(钰泰) |
| Package | ESOP-8 |
| Category | Power Management (PMIC) |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output USB Voltage Range | | 4.8 | 5 | 5.2 | V | | 2 |
| Charge Termination Voltage | | 4.15 | 4.2 | 4.24 | V | | 2 |
| Charging Current | | 0.85 | 1 | 1.15 | A | Charging current =1000/R1, when R1=1K | 2 |
| Switching Frequency | | 1.2 | 1.8 | 2.4 | MHz | | 2 |
| Quiescent Current from battery | | | | 100 | μA | VBAT=3.6V, No load | 2 |
| Maximum Duty Cycle | | | | 90 | % | | 2 |
| ACIN Voltage | | -0.3 | | 6 | V | | 2 |
| OUT Voltage | | -0.3 | | 5 | V | | 2 |
| Operating Temperature Range | | -40 | | 85 | °C | | 2 |
| Storage Temperature Range | | -55 | | 150 | °C | | 2 |
| Thermal Resistance junction-to-case | θJC | | 10 | | °C/W | ESOP-8 | 2 |
## CAD (KiCad official)
- Symbol: `ETA9638E8A`
- Footprint: `Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm`
- 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files: `eta9638e8a-etched.step` / `eta9638e8a-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `eta9638e8a.step` / `eta9638e8a.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [ETA(钰泰) datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8604434023691268096) (5 pp, sha256 `26e3ae895e6b9d2d`, retrieved 2026-11-07, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/eta9638e8a-datasheet.pdf)