component

ET60T-S03-5-05-000-S-R1-S

Public Made by Adom

Samtec Samtec ET60T series board connector (R1 right-angle), Samtec_ET60T-S03-5-05-000-S-R1-S. KiCad symbol, footprint and 3D as used on Adom boards; pin functions from the manufacturer datasheet.

Verified ET60T-S03-5-05-000-S-R1-S

by Claude, at Caleb Taylor's request · last 27 Oct 2026 · 1 record · files match

SymbolFootprint3D modelPins

Verification log 5 records

27 Oct 2026Claude, at Caleb Taylor's requestValidated against Samtec ET60T print Revision Y and recommended PCB layout ET60T-XXX-X-XX-XXX-X-RX-X-X-FOOTPRINT Revision Pfiles match

SymbolFootprint3D modelPinsfor all variants

✓Datasheet: the page already carries Samtec's current ET60T print (Revision Y, sheet date 8/30/2023); sha256 bdd47d4c matches suddendocs.samtec.com/prints/et60t-xxx-x-xx-xxx-x-rx-x-x-mkt.pdf fetched 2026-10-27. Recommended layout checked against et60t-xxx-x-xx-xxx-x-rx-x-x-footprint.pdf Revision P (sheets 1, 3, 8)
✓Part number decoded from the sheet 1 callout: S03 = split power, 3 positions, on the left; 5 signal rows; 05 positions per row; 000 = no power on the right; S = 30 µin gold; R1 = tail for .062 in PCB; S = side guide post; no -H (hot swap)
✓Signal numbering per Fig 4 (p.3), Fig 18 (p.11) and footprint Fig 14: 01 at the left end of the row nearest the board front edge, left to right, rows away from the edge (01 / 03 / 15 labels). Footprint pads 1-25 follow that order (pad 1 at x 11.14, y 3.49 nearest the edge). Renamed signal pins from the board symbol's 31-55 to 01-25
✓Split power per Fig 18 (p.11) and footprint Fig 14: P01L, P01R, P02L, P02R, P03L, P03R left to right, 3.50 mm between the halves, 8.00 mm between positions, 5 tails per half. Pads P1_1-5 / P1_6-10 / P2_1-5 / P2_6-10 / P3_1-5 / P3_6-10 renamed from 1-30 to P01L / P01R / P02L / P02R / P03L / P03R
✓Pin types: all passive (connector contacts); power tails were power_in
✓Footprint vs recommended layout: signal 5 x 5 at 2.00 mm pitch, drill 0.70 (Samtec 0.70 +-0.05 finished PTH), pad 1.00 vs 0.93; power drill 1.02 (Samtec 1.02 +-0.05), pad 1.53 vs 1.25, rows at 2.50 mm; left peg to P01L 5.50, P03R to the first signal column 5.64, last signal column to right peg 5.57, peg centreline to the signal row nearest the edge 4.99, peg centreline on the middle power row; PCB-edge line on Dwgs.User 7.90 mm from the peg centreline as Samtec sheet 1: all match
✓3D body 51.21 x 29.25 x 14.48 mm against the print: envelope 3.32 / 3.68 REF outside the pegs (51.21), depth 29.25 REF, overhang 15.75 REF beyond the front edge (model: 22.15 - (-1.5) - 7.90 = 15.75), 10.00 above the board and 4.48 below vs 4.46 REF
•DigiKey and Mouser do not list this configuration
✓Guide-post holes set to Samtec's 3.20 mm NPTH (2 places, recommended PCB layout rev P); the source board used 3.40 mm
✓Symbol Datasheet / MPN / Manufacturer / DigiKey / Mouser / LCSC properties agree with page.json; footprint Datasheet property points at the manufacturer datasheet URL
✓component-page-verify 0.2.0: all checks pass

Evidenceproduct print (Samtec)recommended PCB layout (Samtec)

Verified files✓ et60t-s03-5-05-000-s-r1-s.kicad_sym✓ et60t-s03-5-05-000-s-r1-s.kicad_mod✓ et60t-s03-5-05-000-s-r1-s.step

9 Oct 2026Claude (AI build)Datasheet pins not matched to a symbol pin: P01L, P01R, P02L, P02R, P03L, P03Rsuperseded

reviewfor all variants

•Datasheet pins not matched to a symbol pin: P01L, P01R, P02L, P02R, P03L, P03R

9 Oct 2026Claude (AI build)Footprint: a "PCB Edge" line on Dwgs.User marks the board front edge 7.90 mm from the peg ...superseded

reviewfor all variants

•Footprint: a "PCB Edge" line on Dwgs.User marks the board front edge 7.90 mm from the peg centreline (Samtec recommended PCB layout ET60T-XXX-X-XX-XXX-X-RX-X-X-FOOTPRINT rev P, sheet 1); documentation only, nothing is cut.

9 Oct 2026Claude (AI build)Datasheet is the Samtec ET60T series print, not a part-specific drawing; confirm the S03-5...superseded

reviewfor all variants

•Datasheet is the Samtec ET60T series print, not a part-specific drawing; confirm the S03-5-05-000-S-R1-S options against its ordering tables.

9 Oct 2026Claude (AI build)Automated build checks (awaiting human validation)superseded

SymbolFootprint3D modelPinsfor all variants

✓Footprint extracted pad-for-pad from the source board and normalized to the footprint frame (back-side parts un-mirrored)
✓3D model seated z=0 at footprint origin (placement inverse; method centroid-matched to KiCad library models on 59 cases)
✓adom-lbr generate + lint passed
✓55 of 55 pins described from the datasheet (adom-ds2sf, page-cited)
•Not yet checked by a person: land pattern vs datasheet, pin-1/orientation, 3D body vs drawing

Evidencedatasheet

Verified files! et60t-s03-5-05-000-s-r1-s.kicad_sym! et60t-s03-5-05-000-s-r1-s.kicad_mod✓ et60t-s03-5-05-000-s-r1-s.step

Spot something wrong? Report it as an issue · Propose a fix Records are signed by members of adom.

Overview Files Discover Packages Releases Dependencies Issues Breadcrumbs Pull Requests Activity

Pull Requests

Open 0 Merged 0 Closed 0

No open pull requests.

Open one from a checkout with adom-wiki pr create adom/et60t-s03-5-05-000-s-r1-s (it carries the diff), or from the Files tab via "Propose a change".