component
EMC2104-BP-TR
Public Made by Adomby adom
Microchip Tech Motor Driver ICs, QFN-20-EP(4x4). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownEMC2104-BP-TR
Microchip Tech · Motor Driver ICs · QFN-20-EP(4x4)
EMC2104-BP-TR from Microchip Tech, in a QFN-20-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DN1 / VIN1 | bidirectional | DN1 is the negative (cathode) analog input for External Diode 1 (default) or VIN1 thermistor voltage input, and must not be exposed to any voltage greater than 2V. |
| 2 | DP1 / VREF_T1 | bidirectional | DP1 is the positive (anode) analog input for External Diode 1 (default) or the VREF_T1 reference output for a thermistor driving VIN1, and must not be exposed to any voltage greater than 2V. |
| 3 | GND | power_in | Ground connection for the device. |
| 4 | VDD | power_in | Power supply pin for the device, specified for a 3.3V supply. |
| 5 | ALERT# | output | Active low interrupt open-drain output that requires an external pull-up resistor and is 5V tolerant. |
| 6 | CLK_IN / GPIO1 | bidirectional | CLK_IN is a 32.768 kHz clock input, or GPIO1 is a general purpose input or push-pull/open-drain output; the pin is 5V tolerant. |
| 7 | SYS_SHDN# | output | Active low critical system shutdown open-drain output that is 5V tolerant. |
| 8 | SMDATA | bidirectional | SMBus data input/output that requires an external pull-up resistor and is 5V tolerant. |
| 9 | SMCLK | bidirectional | SMBus clock input that requires an external pull-up resistor and is 5V tolerant. |
| 10 | PWM2 / GPIO3 | bidirectional | PWM2 is an open-drain PWM drive output for Fan 2 (default), or a push-pull PWM output or GPIO3; the pin is 5V tolerant. |
| 11 | TACH2 / GPIO2 | bidirectional | TACH2 is the tachometer input for Fan 2 (default), or GPIO2 as a general purpose input or push-pull/open-drain output; the pin is 5V tolerant. |
| 12 | TACH1 | input | Tachometer input for Fan 1 that is 5V tolerant. |
| 13 | PWM1 | output | PWM1 is an open-drain PWM drive output for Fan 1 (default) or a push-pull PWM output, and is 5V tolerant. |
| 14 | n/c | unconnected | Not internally connected. |
| 15 | TRIP_SET / VIN4 | input | Analog input that sets the hardware thermal shutdown temperature through an external 1% resistor to GND, or measures VIN4 when SHDN_SEL is high; it must not be exposed to more than 2V. |
| 16 | SHDN_SEL | bidirectional | Strappable input read at power-up with three states (tied to GND, tied to 3.3V, or High-Z) that selects the external diode configuration for critical/thermal shutdown. |
| 17 | DN3 / DP4 / VIN3 | bidirectional | DN3 is the negative (cathode) analog input for External Diode 3 and DP4 the positive (anode) input for External Diode 4 (default), or VIN3 thermistor voltage input; it must not be exposed to more than 2V. |
| 18 | DP3 / DN4 / VREF_T3 | bidirectional | DP3 is the positive (anode) analog input for External Diode 3 and DN4 the negative (cathode) input for External Diode 4 (default), or the VREF_T3 reference output for a thermistor driving VIN3; it must not be exposed to more than 2V. |
| 19 | DN2 / VIN2 | bidirectional | DN2 is the negative (cathode) analog input for External Diode 2 (default) or VIN2 thermistor voltage input, and must not be exposed to more than 2V. |
| 20 | DP2 / VREF_T2 | bidirectional | DP2 is the positive (anode) analog input for External Diode 2 (default) or the VREF_T2 reference output for a thermistor driving VIN2, and must not be exposed to more than 2V. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-20-EP(4x4) |
| Category | Power Supply Chip |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 3 | 3.3 | 3.6 | V | 14 | |
| Voltage on 5V tolerant pins | -0.3 | 6.5 | V | 14 | |||
| Voltage on VDD pin | -0.3 | 4 | V | 14 | |||
| Voltage on 2V tolerant pins | -0.3 | 2.5 | V | 14 | |||
| Voltage on any other pin to GND | -0.3 | V | Maximum is VDD + 0.3 V | 14 | |||
| Package Power Dissipation | 1 | W | Up to TA = 85°C; see Note 3.2 | 14 | |||
| Operating Ambient Temperature Range | -40 | 85 | °C | 14 | |||
| Storage Temperature Range | -55 | 150 | °C | 14 | |||
| Supply Current (active) | IDD | 2 | 3 | mA | 4 Conversions / second - Dynamic Averaging Enabled; Fan Driver enabled at max PWM frequency | 14 | |
| Supply Current | IDD | 500 | 750 | uA | 1 Conversions / second - Dynamic Averaging disabled, Fan Driver disabled. | 14 | |
| Temperature Accuracy | TDIODE | -1 | 0.25 | 1 | °C | 60°C < TDIODE < 110°C; 30°C < TDIE < 85°C | 14 |
| Temperature Accuracy | TDIODE | -2 | 0.5 | 2 | °C | 0°C < TDIODE < 125°C, 0°C < TDIE < 115°C | 15 |
| Diode decoupling capacitor | CFILTER | 2200 | 2700 | pF | Connected across external diode, CPU, GPU, or AMD diode | 15 | |
| Resistance Error Corrected | RSERIES | 100 | Ohm | Sum of series resistance in both DP and DN lines | 15 | ||
| Internal Temperature Monitor Accuracy | TDIE | -2 | 1 | 2 | °C | 15 | |
| PWM Duty Cycle | DUTY | 0 | 100 | % | 15 | ||
| Tachometer Range | TACH | 480 | 16000 | RPM | 15 | ||
| Tachometer Setting Accuracy | ΔTACH | -2 | 1 | 2 | % | External oscillator 32.768kHz | 15 |
| Tachometer Setting Accuracy | ΔTACH | -5 | 2.5 | 5 | % | Internal Oscillator 40°C < TDIE < 100°C | 15 |
| Input High Voltage | VIH | 2 | V | 15 | |||
| Junction to Ambient | θJA | 40 | °C/W | See Note 3.2 | 14 | ||
| Supply Current from VDD_5V | IDD_5 | 100 | uA | Fan Driver enabled, No load current | 15 | ||
| SMBus Delay | tSMB | 15 | ms | Delay from power to first SMBus communication | 15 | ||
| Time to First Round Robin | 300 | ms | 15 | ||||
| Temperature Resolution | 0.125 | °C | 15 | ||||
| Internal Temperature Monitor Resolution | 0.125 | °C | 15 | ||||
| Total Unadjusted Error | TUE | 1 | % | Measured at 3/4 full scale | 15 | ||
| Reference Voltage | VREF | 800 | mV | 15 | |||
| Reference Accuracy | ΔVREF | 1 | % | 15 | |||
| PWM Resolution | PWM | 256 | Steps | 15 |
CAD (KiCad official)
- Symbol:
EMC2104-BP-TR - Footprint:
Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm - 3D model: QFN-20-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
emc2104-bp-tr-etched.step/emc2104-bp-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);emc2104-bp-tr.step/emc2104-bp-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (99 pp, sha256
e00bd67e1384c45b, retrieved 2026-11-02, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).