component
EMC1413-1-AIZL-TR
Public Made by Adomby adom
Microchip Tech Temperature Sensors, MSOP-10. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownEMC1413-1-AIZL-TR
Microchip Tech · Temperature Sensors · MSOP-10
EMC1413-1-AIZL-TR from Microchip Tech, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Power supply pin for the device; for the 5V-tolerant pins with pull-up resistors, the voltage difference between VDD and the pull-up voltage must never exceed 3.6V. |
| 2 | DP1 | passive | External diode 1 positive (anode) connection, an analog I/O pin. |
| 3 | DN1 | passive | External diode 1 negative (cathode) connection, an analog I/O pin. |
| 4 | DP2 / DN3 | passive | External diode 2 positive (anode) connection, which for the EMC1414 only is shared with External Diode 3 negative (cathode) for anti-parallel diodes; analog I/O pin. |
| 5 | DN2 / DP3 | passive | External diode 2 negative (cathode) connection, which for the EMC1414 only is shared with External Diode 3 positive (anode) for anti-parallel diodes; analog I/O pin. |
| 6 | GND | power_in | Ground connection for the device. |
| 7 | THERM / ADDR | bidirectional | THERM is the critical temperature output that requires a pull-up resistor and is 5V tolerant open drain; ADDR selects the SMBus address based on the pull-up resistor value and is 5V tolerant. |
| 8 | ALERT | output | Active low digital ALERT output that requires a pull-up resistor, is open drain, and is 5V tolerant. |
| 9 | SMDATA | bidirectional | SMBus data input/output that requires a pull-up resistor, is open drain when used as an output, and is 5V tolerant. |
| 10 | SMCLK | input | SMBus clock input that requires a pull-up resistor and is 5V tolerant. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-10 |
| Category | Sensors |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 3 | 3.3 | 3.6 | V | 11 | |
| Supply Voltage (absolute maximum) | VDD | -0.3 | 4 | V | 10 | ||
| Voltage on 5V tolerant pins | V5VT_pin | -0.3 | 5.5 | V | 10 | ||
| Voltage on 5V tolerant pins vs VDD | /V5VT_pin - VDD/ | 0 | 3.6 | V | see Note 4.1 | 10 | |
| Voltage on any other pin to Ground | -0.3 | V | 10 | ||||
| Operating Temperature Range | TA | -40 | 125 | °C | 10 | ||
| Storage Temperature Range | TSTG | -55 | 150 | °C | 10 | ||
| ESD Rating, All pins HBM | 2000 | V | HBM | 10 | |||
| Thermal Resistance (j-a), MSOP-10 | θJA | 132.2 | °C/W | Package Thermal Characteristics for MSOP-10 | 10 | ||
| Supply Current | IDD | 430 | 850 | μA | 1 conversion / sec, dynamic averaging disabled | 11 | |
| Supply Current | IDD | 930 | 1200 | μA | 4 conversions / sec, dynamic averaging enabled | 11 | |
| Supply Current | IDD | 1120 | μA | > 16 conversions / sec, dynamic averaging enabled | 11 | ||
| Standby Supply Current | IDD | 170 | 230 | μA | Device in Standby mode, no SMBus communications, ALERT and THERM pins not asserted. | 11 | |
| Internal Temperature Monitor Temperature Accuracy | -1 | 0.25 | 1 | °C | -5°C < TA < 100°C | 11 | |
| Internal Temperature Monitor Temperature Accuracy | -2 | 2 | °C | -40°C < TA < 125°C | 11 | ||
| External Temperature Monitor Temperature Accuracy | -1 | 0.25 | 1 | °C | +20°C < TDIODE < +110°C, 0°C < TA < 100°C | 11 | |
| External Temperature Monitor Temperature Accuracy | -2 | 0.5 | 2 | °C | -40°C < TDIODE < 127°C | 11 | |
| Output Low Voltage | VOL | 0.4 | V | ISINK = 8mA | 11 | ||
| Leakage Current (ALERT and THERM pins) | ILEAK | -5 | 5 | μA | Device powered or unpowered; TA < 85°C; pull-up voltage < 3.6V | 11 | |
| Capacitive Filter (across external diode) | CFILTER | 2.2 | 2.7 | nF | Connected across external diode | 11 | |
| Input High Voltage | VIH | 2 | V | 5V Tolerant | 12 | ||
| Input Low Voltage | VIL | -0.3 | 0.8 | V | 5V Tolerant | 12 | |
| Leakage Current (SMBus) | ILEAK | -5 | 5 | μA | Powered or unpowered; TA < 85°C | 12 | |
| Output Low Sink Current | IOL | 8.2 | 15 | mA | SMDATA = 0.4V | 12 | |
| Clock Frequency | fSMB | 10 | 400 | kHz | 12 | ||
| Spike Suppression | tSP | 50 | ns | 12 | |||
| Clock/Data Fall time | tFALL | 300 | ns | Min = 20+0.1CLOAD ns | 12 | ||
| Clock/Data Rise time | tRISE | 300 | ns | Min = 20+0.1CLOAD ns | 12 | ||
| Capacitive Load | CLOAD | 400 | pF | per bus line | 12 | ||
| Bus Free Time Stop to Start | tBUF | 1.3 | μs | 12 | |||
| Hold Time: Start | tHD:STA | 0.6 | μs | 12 | |||
| Setup Time: Start | tSU:STA | 0.6 | μs | 12 | |||
| Setup Time: Stop | tSU:STO | 0.6 | μs | 12 | |||
| Data Hold Time | tHD:DAT | 0 | μs | When transmitting to the master | 12 | ||
| Data Hold Time | tHD:DAT | 0.3 | μs | When receiving from the master | 12 | ||
| Data Setup Time | tSU:DAT | 100 | ns | 12 | |||
| Clock Low Period | tLOW | 1.3 | μs | 12 | |||
| Clock High Period | tHIGH | 0.6 | μs | 12 | |||
| Input Capacitance | CIN | 5 | pF | 12 | |||
| Hysteresis | 420 | mV | 12 | ||||
| Conversion Time, all channels | tCONV | 150 | ms | default settings | 11 | ||
| Internal Temperature Resolution | 0.125 | °C | 11 | ||||
| External Temperature Resolution | 0.125 | °C | 11 |
CAD (KiCad official)
- Symbol:
EMC1413-1-AIZL-TR - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
emc1413-1-aizl-tr-etched.step/emc1413-1-aizl-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);emc1413-1-aizl-tr.step/emc1413-1-aizl-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (54 pp, sha256
59cf383eb07ca8b0, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).