component
EG6599S
Public Made by Adomby adom
EG Micro AC-DC Controllers & Regulators, SOP-16. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
Ray
Publish 0.1.0
1f33d80
EG6599S
EG Micro · AC-DC Controllers & Regulators · SOP-16
EG6599S from EG Micro, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CSS | passive | Soft-start capacitor pin, discharged when VCC is below UVLO, LINE is below 1.25V or above 6V, DIS is above 1.85V, ISEN is above 1.5V, or DELAY is above 3.5V. |
| 2 | DELAY | passive | Overcurrent delay pin; above 2V the soft-start capacitor fully discharges and the switching frequency goes to maximum, the IC shuts off above 3.5V and restarts once the voltage falls below 0.3V. |
| 3 | CF | passive | External oscillator capacitor pin. |
| 4 | RFMIN | passive | Minimum oscillator frequency setting pin that provides a 2V reference voltage. |
| 5 | STBY | input | Burst mode pin; below 1.25V the IC enters low-power standby, above 1.25V it operates normally, and it must be tied to RFMIN if burst mode is not used. |
| 6 | ISEN | input | Current sense input; above 0.8V the soft-start capacitor discharges, and above 1.5V the IC enters low-power state and needs a power restart to clear the latch. |
| 7 | LINE | input | High-side line voltage detection; below 1.25V the IC enters low-power state, and if unused the pin must be biased between 1.25V and 6V. |
| 8 | DIS | input | Latched shutdown input; above 1.85V the IC enters low-power state and needs a power restart to clear the latch, and if unused it must be connected to GND. |
| 9 | PFC_STOP | output | Open-collector PFC drive control output that is pulled low when DIS > 1.85V, ISEN > 1.5V, LINE > 6V, STBY < 1.25V or DELAY > 2V, and is left floating if unused. |
| 10 | GND | power_in | Chip ground pin. |
| 11 | LVG | output | Low-side gate driver output with 0.3A source and 0.8A sink current capability. |
| 12 | VCC | power_in | Chip operating power supply input; the VCC on-voltage is 9.5V to 11.5V and the absolute maximum is 19V. |
| 13 | NC | unconnected | No connection; leave floating. |
| 14 | OUT | power_in | High-side driver floating ground reference. |
| 15 | HVG | output | High-side gate driver output with 0.3A source and 0.8A sink current capability. |
| 16 | VBOOT | power_in | High-side driver floating supply input; the absolute maximum rating is 650V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | EG Micro |
| Package | SOP-16 |
| Category | Power Management |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VBOOT 自举高端电源 | VBOOT | -0.3 | 650 | V | 7 | ||
| LVG 低端输出 | LVG | -0.3 | V | 7 | |||
| VCC 电源 | VCC | -0.3 | 19 | V | 7 | ||
| VPFC_STOP 最高电压 | VPFC_STOP | -0.3 | V | 7 | |||
| IRFMIN 最大电流 | IRFMIN | 2 | mA | 7 | |||
| TA 环境温度 | TA | -40 | 125 | ℃ | 7 | ||
| Tstr 储存温度 | Tstr | -55 | 150 | ℃ | 8 | ||
| TL 焊接温度 | TL | 300 | ℃ | T=10S | 8 | ||
| 电源 | VCC | 8.8 | 15 | 17 | V | 8 | |
| VCC 开启电压 | Vcc(on) | 9.5 | 10.5 | 11.5 | V | 8 | |
| VCC 关断电压 | Vcc(off) | 7 | 7.9 | 8.8 | V | 8 | |
| 启动电流 | Istart-up | 200 | 300 | uA | VCC=VCC-0.2V | 8 | |
| 静态电流 | IQ | 1.4 | 2 | mA | VSTBY=1V | 8 | |
| 工作电流 | IOP | 2 | 5 | mA | VSTBY=VRFMIN | 8 | |
| 关闭电流 | IQ | 270 | 400 | uA | VDIS>1.85V or VDELAY>3.5V or VLINE<1.25V or VLINE=Vclamp | 8 | |
| 高侧浮动栅极驱动电源 VBOOT 漏电流 | ILKBOOT | 5 | uA | VBOOT=580V | 8 | ||
| VOUT 漏电流 | ILKOUT | 5 | uA | VOUT=562V | 8 | ||
| 过流比较器 输入偏置电流 | IISEN | -1 | uA | VISEN=0 | 8 | ||
| 频移开启电压 | VISEN | 0.76 | 0.8 | 0.84 | V | 8 | |
| 锁存关闭电压 | VISENDIS | 1.44 | 1.5 | 1.56 | V | 8 | |
| 输出延时 | TD(H-L) | 300 | 400 | nS | 8 | ||
| 母线检测 检测开启 | VTH | 1.2 | 1.25 | 1.3 | V | 8 | |
| 母线检测 迟滞电流 | IHYST | 12 | 15 | 18 | uA | VCC>5V,VLINE=0.3V | 8 |
| 母线检测 钳位电压 | Vclamp | 6 | 8 | V | ILINE=1 mA | 8 | |
| DIS 功能 输入偏置电流 | IDIS | -1 | uA | VDIS=0 | 8 | ||
| 关闭电压门限 | VTH | 1.71 | 1.85 | 1.93 | V | 9 | |
| 振荡器 占空比 | D | 48 | 50 | 52 | % | HVG 和 LVG | 9 |
| 振荡器 频率 | FOSC | 56 | 60 | 64 | KHZ | 9 | |
| 振荡器 频率 | FOSC | 240 | 250 | 260 | KHZ | RRFMIN=2.7K | 9 |
| 振荡器 推荐最大频率 | 500 | KHZ | 推荐最大 | 9 | |||
| 振荡器 死区 | TD | 0.2 | 0.3 | 0.4 | Us | 9 | |
| 基准 | VREF | 1.93 | 2 | 2.07 | V | 9 | |
| 电阻范围 | RFMIN | 1 | 100 | KΩ | 9 | ||
| PFC_STOP 功能 漏电流 | Ileak | 1 | uA | VPFC_STOP=VCC | 9 | ||
| PFC_STOP 功能 低电平电压 | VL | 0.2 | V | IPFC_STOP=1mA DIS=2V | 9 | ||
| 软启动 漏电流 | Ileak | 0.5 | uA | VCSS=2V | 9 | ||
| 猝发模式 偏置电流 | IDIS | -1 | uA | VDIS=0 | 9 | ||
| 猝发模式 门限电压 | VTH | 1.2 | 1.25 | 1.3 | V | 9 | |
| 过流延时 漏电流 | Ileak | 0.5 | uA | 9 | |||
| 过流延时 电流源 | ICHARGE | 100 | 150 | 200 | uA | VDELAY=1V, VISEN=0.85V | 9 |
| 过流延时 门限 1 | VTH1 | 1.93 | 2 | 2.07 | V | 9 | |
| 过流延时 门限 2 | VTH2 | 3.3 | 3.5 | 3.7 | V | 9 | |
| 过流延时 门限 3 | VTH3 | 0.25 | 0.3 | 0.35 | V | 9 | |
| 低端驱动 输出低电平 | VLVGL | 1.5 | V | ISINK=200mA | 9 | ||
| 低端驱动 输出高电平 | VLGH | 12.8 | 13.3 | V | ISOURCE=5mA | 9 | |
| 低端驱动 峰值拉电流 | ISORUCEPK | -0.3 | A | 10 | |||
| 低端驱动 峰值灌电流 | ISINKPK | 0.8 | A | 10 | |||
| 高端驱动 输出低电平 | VHVGL | 1.5 | V | ISINK=200mA | 10 | ||
| 高端驱动 输出高电平 | VHGH | 12.8 | 13.3 | V | ISOURCE=5mA | 10 | |
| 高端驱动 峰值拉电流 | ISORUCEPK | -0.3 | A | 10 | |||
| 高端驱动 峰值灌电流 | ISINKPK | 0.8 | A | 10 |
CAD (KiCad official)
- Symbol:
EG6599S - Footprint:
Package_SO:SOIC-16_3.9x9.9mm_P1.27mm - 3D model: SOP-16 (KiCad packages3D, STEP)
- 3D model files:
eg6599s-etched.step/eg6599s-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);eg6599s.step/eg6599s.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: EG Micro datasheet (22 pp, sha256
db687e6488d7add7, retrieved 2026-11-04, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# EG6599S
**EG Micro** · AC-DC Controllers & Regulators · SOP-16
EG6599S from EG Micro, in a SOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CSS | passive | Soft-start capacitor pin, discharged when VCC is below UVLO, LINE is below 1.25V or above 6V, DIS is above 1.85V, ISEN is above 1.5V, or DELAY is above 3.5V. |
| 2 | DELAY | passive | Overcurrent delay pin; above 2V the soft-start capacitor fully discharges and the switching frequency goes to maximum, the IC shuts off above 3.5V and restarts once the voltage falls below 0.3V. |
| 3 | CF | passive | External oscillator capacitor pin. |
| 4 | RFMIN | passive | Minimum oscillator frequency setting pin that provides a 2V reference voltage. |
| 5 | STBY | input | Burst mode pin; below 1.25V the IC enters low-power standby, above 1.25V it operates normally, and it must be tied to RFMIN if burst mode is not used. |
| 6 | ISEN | input | Current sense input; above 0.8V the soft-start capacitor discharges, and above 1.5V the IC enters low-power state and needs a power restart to clear the latch. |
| 7 | LINE | input | High-side line voltage detection; below 1.25V the IC enters low-power state, and if unused the pin must be biased between 1.25V and 6V. |
| 8 | DIS | input | Latched shutdown input; above 1.85V the IC enters low-power state and needs a power restart to clear the latch, and if unused it must be connected to GND. |
| 9 | PFC_STOP | output | Open-collector PFC drive control output that is pulled low when DIS > 1.85V, ISEN > 1.5V, LINE > 6V, STBY < 1.25V or DELAY > 2V, and is left floating if unused. |
| 10 | GND | power_in | Chip ground pin. |
| 11 | LVG | output | Low-side gate driver output with 0.3A source and 0.8A sink current capability. |
| 12 | VCC | power_in | Chip operating power supply input; the VCC on-voltage is 9.5V to 11.5V and the absolute maximum is 19V. |
| 13 | NC | unconnected | No connection; leave floating. |
| 14 | OUT | power_in | High-side driver floating ground reference. |
| 15 | HVG | output | High-side gate driver output with 0.3A source and 0.8A sink current capability. |
| 16 | VBOOT | power_in | High-side driver floating supply input; the absolute maximum rating is 650V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | EG Micro |
| Package | SOP-16 |
| Category | Power Management |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VBOOT 自举高端电源 | VBOOT | -0.3 | | 650 | V | | 7 |
| LVG 低端输出 | LVG | -0.3 | | | V | | 7 |
| VCC 电源 | VCC | -0.3 | | 19 | V | | 7 |
| VPFC_STOP 最高电压 | VPFC_STOP | -0.3 | | | V | | 7 |
| IRFMIN 最大电流 | IRFMIN | | | 2 | mA | | 7 |
| TA 环境温度 | TA | -40 | | 125 | ℃ | | 7 |
| Tstr 储存温度 | Tstr | -55 | | 150 | ℃ | | 8 |
| TL 焊接温度 | TL | | | 300 | ℃ | T=10S | 8 |
| 电源 | VCC | 8.8 | 15 | 17 | V | | 8 |
| VCC 开启电压 | Vcc(on) | 9.5 | 10.5 | 11.5 | V | | 8 |
| VCC 关断电压 | Vcc(off) | 7 | 7.9 | 8.8 | V | | 8 |
| 启动电流 | Istart-up | | 200 | 300 | uA | VCC=VCC-0.2V | 8 |
| 静态电流 | IQ | | 1.4 | 2 | mA | VSTBY=1V | 8 |
| 工作电流 | IOP | | 2 | 5 | mA | VSTBY=VRFMIN | 8 |
| 关闭电流 | IQ | | 270 | 400 | uA | VDIS>1.85V or VDELAY>3.5V or VLINE<1.25V or VLINE=Vclamp | 8 |
| 高侧浮动栅极驱动电源 VBOOT 漏电流 | ILKBOOT | | | 5 | uA | VBOOT=580V | 8 |
| VOUT 漏电流 | ILKOUT | | | 5 | uA | VOUT=562V | 8 |
| 过流比较器 输入偏置电流 | IISEN | | | -1 | uA | VISEN=0 | 8 |
| 频移开启电压 | VISEN | 0.76 | 0.8 | 0.84 | V | | 8 |
| 锁存关闭电压 | VISENDIS | 1.44 | 1.5 | 1.56 | V | | 8 |
| 输出延时 | TD(H-L) | | 300 | 400 | nS | | 8 |
| 母线检测 检测开启 | VTH | 1.2 | 1.25 | 1.3 | V | | 8 |
| 母线检测 迟滞电流 | IHYST | 12 | 15 | 18 | uA | VCC>5V,VLINE=0.3V | 8 |
| 母线检测 钳位电压 | Vclamp | 6 | | 8 | V | ILINE=1 mA | 8 |
| DIS 功能 输入偏置电流 | IDIS | | | -1 | uA | VDIS=0 | 8 |
| 关闭电压门限 | VTH | 1.71 | 1.85 | 1.93 | V | | 9 |
| 振荡器 占空比 | D | 48 | 50 | 52 | % | HVG 和 LVG | 9 |
| 振荡器 频率 | FOSC | 56 | 60 | 64 | KHZ | | 9 |
| 振荡器 频率 | FOSC | 240 | 250 | 260 | KHZ | RRFMIN=2.7K | 9 |
| 振荡器 推荐最大频率 | | | | 500 | KHZ | 推荐最大 | 9 |
| 振荡器 死区 | TD | 0.2 | 0.3 | 0.4 | Us | | 9 |
| 基准 | VREF | 1.93 | 2 | 2.07 | V | | 9 |
| 电阻范围 | RFMIN | 1 | | 100 | KΩ | | 9 |
| PFC_STOP 功能 漏电流 | Ileak | | | 1 | uA | VPFC_STOP=VCC | 9 |
| PFC_STOP 功能 低电平电压 | VL | | | 0.2 | V | IPFC_STOP=1mA DIS=2V | 9 |
| 软启动 漏电流 | Ileak | | | 0.5 | uA | VCSS=2V | 9 |
| 猝发模式 偏置电流 | IDIS | | | -1 | uA | VDIS=0 | 9 |
| 猝发模式 门限电压 | VTH | 1.2 | 1.25 | 1.3 | V | | 9 |
| 过流延时 漏电流 | Ileak | | | 0.5 | uA | | 9 |
| 过流延时 电流源 | ICHARGE | 100 | 150 | 200 | uA | VDELAY=1V, VISEN=0.85V | 9 |
| 过流延时 门限 1 | VTH1 | 1.93 | 2 | 2.07 | V | | 9 |
| 过流延时 门限 2 | VTH2 | 3.3 | 3.5 | 3.7 | V | | 9 |
| 过流延时 门限 3 | VTH3 | 0.25 | 0.3 | 0.35 | V | | 9 |
| 低端驱动 输出低电平 | VLVGL | | | 1.5 | V | ISINK=200mA | 9 |
| 低端驱动 输出高电平 | VLGH | 12.8 | 13.3 | | V | ISOURCE=5mA | 9 |
| 低端驱动 峰值拉电流 | ISORUCEPK | -0.3 | | | A | | 10 |
| 低端驱动 峰值灌电流 | ISINKPK | 0.8 | | | A | | 10 |
| 高端驱动 输出低电平 | VHVGL | | | 1.5 | V | ISINK=200mA | 10 |
| 高端驱动 输出高电平 | VHGH | 12.8 | 13.3 | | V | ISOURCE=5mA | 10 |
| 高端驱动 峰值拉电流 | ISORUCEPK | -0.3 | | | A | | 10 |
| 高端驱动 峰值灌电流 | ISINKPK | 0.8 | | | A | | 10 |
## CAD (KiCad official)
- Symbol: `EG6599S`
- Footprint: `Package_SO:SOIC-16_3.9x9.9mm_P1.27mm`
- 3D model: SOP-16 (KiCad packages3D, STEP)
- 3D model files: `eg6599s-etched.step` / `eg6599s-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `eg6599s.step` / `eg6599s.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [EG Micro datasheet](docs/eg6599s-datasheet.pdf) (22 pp, sha256 `db687e6488d7add7`, retrieved 2026-11-04, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/eg6599s-datasheet.pdf)